3.0X1.5mm INFRARED EMITTING DIODE Part Number: APL3015SF4C-F01 Features Description z 3.0mmx1.5mm SMT LED, 1.4mm thickness. SF4 Made with Gallium Aluminum Arsenide Infrared Emit- z Mechanically and spectrally matched to the phototransistor. ting diodes. z Package : 2000pcs / reel. z Moisture sensitivity level : level 3. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.2(0.008") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAF1076 REV NO: V.3B DATE: JUN/25/2014 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001613 Selection Guide Po (mW/sr) [2] Viewing @ 20mA Angle [1] Part No. Dice Lens Type Min. Typ. 2θ1/2 APL3015SF4C-F01 SF4 (GaAIAs) Water Clear 0.8 2 70° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Radiant Intensity/ luminous flux: +/-15%. 3. Radiant intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Parameter P/N Symbol Typ. Max. Units Test Conditions Forward Voltage [1] SF4 VF 1.3 1.6 V IF=20mA Reverse Current SF4 IR 10 uA VR = 5V Capacitance SF4 C 90 pF VF=0V;f=1MHz Peak Spectral Wavelength SF4 λP 880 nm IF=20mA Spectral Bandwidth SF4 Δλ1/2 50 nm IF=20mA Note: 1. Forward Voltage: +/-0.1V. 2. Wavelength value is traceable to the CIE127-2007 compliant national standards. Absolute Maximum Ratings at TA=25°C Parameter Symbol SF4 Units Power dissipation PD 80 mW F 50 mA DC Forward Current I Peak Forward Current [1] iFS 1.2 A Reverse Voltage VR 5 V Operating Temperature TA -40 To +85 °C Storage Temperature TSTG -40 To +85 °C Note: 1. 1/100 Duty Cycle, 10μs Pulse Width. SPEC NO: DSAF1076 REV NO: V.3B DATE: JUN/25/2014 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001613 APL3015SF4C-F01 SPEC NO: DSAF1076 REV NO: V.3B DATE: JUN/25/2014 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001613 APL3015SF4C-F01 Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern Reel Dimension (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAF1076 REV NO: V.3B DATE: JUN/25/2014 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001613 PACKING & LABEL SPECIFICATIONS APL3015SF4C-F01 Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF1076 REV NO: V.3B DATE: JUN/25/2014 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Y.Liu ERP: 1203001613