Direct Discrimination Unit E63-WF CSM_E63-WF_DS_E_4_2 Detects the Rotary Encoder Direction • Input phase difference signal from the Encoder to detect the direction of rotation. High-speed response at 120 kHz. Mounts to DIN Track. Thin design enables superb mounting efficiency. Front-panel switch enables reversing phase Z logic. Enables connecting either voltage outputs or open-collector outputs. Be sure to read Safety Precautions on page 3. Ordering Information Power supply voltage Output configuration Model 12 to 24 VDC Open-collector output E63-WF5C Ratings and Specifications Direct Discrimination Unit [Refer to Dimensions on page 4.] Item Model E63-WF5C Power supply voltage 12 VDC −10% to 24 VDC +15%, ripple (p-p): 5% max. Current consumption 50 mA max. Input signal Phases A, B, and Z (phase difference signals) Phase difference 90° ±45° max. ON 6 mA max. at 0 to 2 V Input OFF 1.5 mA max. at 8 to 24 V Input short current 9 mA Max. applied voltage 30 V max. Input impedance Approx. 1 Ω Output signal UP/DOWN (direction detection), COUNTS output (count), OUT Z Output configuration Open-collector output Output Applied voltage: 30 VDC max. Sink current: 80 mA max. Output capacity Residual voltage: 1 V max. (at sink current of 80 mA) Residual voltage: 0.4 V max. (at sink current of 20 mA) Maximum response 120 kHz frequency Output response time 2 μs max. Indicators Power indicator (red), Phase Z output indicator (green) Ambient temperature range Operating: −10 to 55°C (with no icing), Storage: −25 to 80°C (with no icing) Ambient humidity range Operating/Storage: 35% to 85% (with no condensation) Vibration resistance Destruction: 10 to 55 Hz, 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions 2 Shock resistance Destruction: 300 m/s 3 times each in X, Y, and Z directions Connection method Terminal block Material Case: ABS Weight (packed state) Approx. 100 g Accessories Instruction manual (S3D8 Connector is not provided.) 1 E63-WF I/O Circuit Diagrams Input Circuits (IN A, IN B, IN Z) Operate Terminal Signal No. E63 Phase ZZ IN (A, B, Z) 1 0 V (common) main switch circuit 2 Encoder power supply: 12 to 24 VDC 9 mA (Top: Z, Bottom: Z) 3IN A 0 V 4IN B Power indicator 5 0 V (common) Output Circuits (UP/DOWN, COUNTS, OUT Z) (red) 6 Power supply: 12 to 24 V Phase Z 7 COUNTS output output +12 to 24 V indicator 8UP/DOWN Output (UP/DOWN, (green) COUNTS, 9OUT Z E63 OUT Z) main 10 IN Z circuit 30 VDC 80 mA max. Note: Terminals 2 and 6 are connected internally. 0 V Timing Charts Relation between Inputs (phase A and phase B) and Outputs (COUNTS, UP/DOWN) Encoder CW CCW CW CCW CW CCW CW CCW CW direction ON Phase A OFF IN ON Phase B OFF ON COUNTS OFF OUTPUT OUT ON UP/DOWN OFF Relation between IN Z and OUT Z Using a Rotary Encoder with an Open-collector Output Using a Rotary Encoder with a Voltage Output Phase ZZ Switch Phase ZZ Switch Phase ZZ Switch Z Z Z Z Z Z ON ON H IN Z IN Z IN Z OFF OFF L ON ON ON OUT Z OUT Z OUT Z OFF OFF OFF ON ON ON COUNTS COUNTS COUNTS OUTPUT OUTPUT OUTPUT OFF OFF OFF ON ON ON Phase Z Phase Z Phase Z OF OF OFF Note: The output from a Rotary output output output indicator indicator indicator Encoder with a Voltage *Set the phase ZZ switch to Z. *Set the phase ZZ switch to Z. *Set the phase ZZ switch to Z. Output can switch 9 mA. Connection Rotary Encoder Connection Example +12 to 24 V 5 6 E63-WF5C 7 8 COUNTS OUTPUT UP/DOWN 9 OUT Z 10 3 4 1 2 Brown 12 to 24 V Black (phase A) White (phase B) Orange (phase Z) Note 1: Used only to reset the counter using phase Z. When doing so, set the phase ZZ switch to Z Blue (0 V) Rotary Encoder and use a Rotary Encoder with an Open-collector Output. Shield 2: When using phase Z, be sure that the width of phase Z is the same as or wider than the width of phase A. 3. Use one of the following Rotary Encoders: E6A2-CW3C, E6A2-CW5C, E6A2-CWZ3C, E6B2- CWZ6C, E6H-CWZ6C, E6C2-CWZ6C, or E6D-CWZ2C. 2 E63-WF Safety Precautions Refer to Warranty and Limitations of Liability. WARNING This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Precautions for Correct Use Do not use the Encoder under ambient conditions that exceed the ratings. ● Mounting • Removal from DIN Track • Mount to DIN Track as shown in the following diagram. Pull down on the track stopper (C) with a flat-blade screwdriver and • Hook part (A) at the top of the E63-WF on the DIN Track first and then remove the E63-WF from the DIN Track. When using DIN then press in on the E63-WF in the direction indicated by (B). standard 35 track, keep other devices on the track separated from the E63-WF by at least 30 mm to facilitate mounting and removal. 30 mm min. (B) DIN Track (DIN standard 35) (PFP-100N or Track stopper PFP-100N2) (yellow) (A) (C) 30 mm min. • Do not place the connection cable together with high-voltage cables. Keep it isolated from other cables whenever possible. • The response speed of the E63-WF is 120 kHz. Do not allow the Rotary Encoder to exceed this speed. ● Connection Spurious pulses may be generated when power is turned ON and OFF. Wait at least 0.1 s after turning ON the power to the Encoder before using the connected device, and stop using the connected device at least 0.1 s before turning OFF the power to the Encoder. Also, turn ON the power to the load only after turning ON the power to the Encoder. 3 E63-WF (Unit: mm) Dimensions Tolerance class IT16 applies to dimensions in this datasheet unless otherwise specified. E63-WF Mounting Hole 7.5 75 Two, M4 screw mounting holes 4.5 Dimensions Two, 4.5-dia. or M4 mounting holes 62.5 66 64 75 50 26.5 * 22.5 65 12.5 12.7 72.5 13 80 DIN Track mounting location *: Detail 12.5 13 4 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranty and Limitations of Liability WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. LIMITATIONS OF LIABILITY OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR. Application Considerations SUITABILITY FOR USE OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:  Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.  Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations.  Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. PROGRAMMABLE PRODUCTS OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIONS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual specifications of purchased products. DIMENSIONS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability. ERRORS AND OMISSIONS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. 2012.8 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2012 All Right Reserved.