MINT1065D 65W Single Output Series rd Medical, 3 Edition Certified Universal Input Power Supply 3 Year Warranty •65W Convection Cooled AC-DC Power Supply •Universal Input 90-264 VAC •Class I or Class II input versions •Less 0.5W No Load Power Dissipation •Rugged EMC Compliant Design •2” x 4” x 1.2” Package •ANSI AAMI ES/CSA/EN/IEC 60601-1, 3rd Edition Certified •Meets Efficiency Level IV Efficiency • Compliant (LVD, RoHS) •Optional Chassis/Cover RoHS Specifications All Specifications are typical at nominal input, full load at 25C unless otherwise stated. AC Input Turn On Time 100-240VAC +/- 10%, 47-63 Hz single phase. Less than 1 second under all rated load conditions. Input Current Hold-up Time 115VAC: 0.7A, 230VAC: 1.5A. <17 ms at 65W, nominal input (120VAC). Inrush Current Overvoltage Protection The inrush at 264VAC, at a cold start, will not exceed 40A. Built-in Input Fuses Overload Protection F1, F2: 2.5A, 250VAC fuses provided on all models. Hiccup Mode Efficiency Short Circuit Protection Up to 90% typical. Hiccup Mode Earth Leakage Current Isolation <300μA @ 264Vac, 60Hz, normal; <500μA SFC. Touch Current is Input-Output: 4000Vac/2 MOOP <100µA NC, <500µA SFC @ 264Vac, 60Hz, measured from output to Input-Ground: 1500Vac/1 MOOP ground Output Power Medical Safety Standards 65W continuous. ANSI AAMI ES/CSA/EN/IEC 60601-1, 3rd Edition Ripple and Noise Switching Frequency 1% pk-pk max., 20MHz BW, differential mode. Measured with noise Variable 50-75kHz typical. probe directly across output terminals. Output Voltage Operating Temperature See chart. 0 to 70C (derate from full rated power above 40C). Voltage Adjustability Cooling Voltage pre-set by fixed resistance. Convection Minimum Load Output Power Derating Not required. See derating chart Total Regulation Storage Temperature +/- 2%. See chart. -40 to +85C. Transient Response Relative Humidity 500μs max., 50% load step, typical. 5% to 95%, non-condensing ______________________________________________________________________________________________________________________________ 1 of 3 SL Power Electronics Corp 6050 King Drive Ventura, CA 93003 Phone 805.486.4565 Fax 858.712.2040 Email: info@slpower.com www.slpower.com MINT1065D 65W Single Output Series rd Medical 3 Edition Certified Universal Input Power Supply 3 Year Warranty Output Parameters Model Output Current Ripple Total OVP Number Volts (V) Open Frame w/cover & Noise Regulation Threshold MINT1065D1275K01 12V 5.25A 4.00A 120mV ±2% 15.0 ± 1.5V MINT1065D1375K01 13.2V 4.80A 3.63A 140mV ±2% 16.0 ± 1.5V MINT1065D1575K01 15V 4.33A 3.20A 150mV ±2% 18.0 ± 1.5V MINT1065D1875K01 18V 3.50A 2.66A 180mV ±2% 21.0 ± 2.0V MINT1055D2075K01 20V 3.25A 2.40A 200mV ±2% 23.0 ± 2.0V MINT1065D2475K01 24V 2.70A 2.00A 240mV ±2% 27.0 ± 2.0V MINT1065D4875K01 48V 1.35A 1.00A 480mV ±2% 55.0 ± 4.0V Specifications (continued) Vibration Shock 2 Operating: 0.003 g /Hz, 1.5 g overall, 3 axes, 10 min. / axis Operating: Half-sine, 20 g , 10 ms, 3 axes, 6 shocks total rms pk 2 Non-Operating: 0.026 g /Hz, 5.0 g overall, 3 axes, 1 hr. / axis Non-Operating: Half-sine, 40 g , 10 ms, 3 axes, 6 shocks total rms pk Pollution Degree Overvoltage Category 2 OVCII (2500V for Mains), OVCI (1500V for Secondary) Dimensions Operating Altitude W 2.0” x L 4.0” x H 1.17”. See outline drawing. Up to 4000m. Weight Non-operating Altitude 150 grams -500 to 40,000 ft. EMI/EMC Compliance Conducted Emissions EN55011 Class B, FCC Part 15, Class B. Radiated Emissions EN55011 Class A, FCC Part 15, Class A. Static Discharge Immunity EN61000-4-2, 6kV Contact Discharge, 8kV air discharge Radiated RF Immunity EN61000-4-3, 3V/m. EFT/Burst Immunity EN61000-4-4, 2kV/5kHz.. Line Surge Immunity EN61000-4-5, 1kV differential, 2kV common-mode Conducted RF Immunity EN61000-4-6, 3Vrms Power Frequency Magnetic Field Immunity EN61000-4-8, 3A/m Voltage Dip Immunity EN61000-4-11 240VAC, 0%/0.5 cycle, 40%/5cycles, 70%/25 cycles Model Number Key MINT 1 065 X 12 75 K 01 Model: "01" = Standard Model, 02 and higher indicates a modified model. Input Connector: "K" = 3 pin Header (class I input); "C" = 2 pin Header (class II input). Output Connector: "75" = Output Connector, 4 pin header. Other options available, consult factory. Output Voltage: "12" = 12V, "24" = 24V, etc. Configuration: "D" = EN60601-1 3rd Edition Certified, "C" = Optional chassis & cover (class I only). Output Pow er: "065" = 65W # of Outputs: "1" = Single output Product Family: "M" = Medical, "I" = Internal, "NT" = New Technology ______________________________________________________________________________________________________________________________ 2 of 3 SL Power Electronics Corp 6050 King Drive Ventura, CA 93003 Phone 805.486.4565 Fax 858.712.2040 Email: info@slpower.com www.slpower.com MINT1065D 65W Single Output Series rd Medical 3 Edition Certified Universal Input Power Supply 3 Year Warranty Mechanical Drawings and Connector Information MINT1065 Series Connectors INPUT: J1 AMP P/N 641937-1 PIN 1) AC LINE PIN 2) AC NEUTRAL OUTPUT: J2 AMP P/N 640445-4 PIN 1) +Vout PIN 3) -Vout PIN 2) +Vout PIN 4) -Vout MATING CONNECTORS: P1 Molex 09-50-3031 P2 Molex 09-50-3041 Pins: Molex 08-50-0105 GND CONNECTION (Class I version) 0.187" FASTON TAB Output Power Derating Curve Data Sheet © 2012 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication. Rev. 12-19-12 However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice. ______________________________________________________________________________________________________________________________ 3 of 3 SL Power Electronics Corp 6050 King Drive Ventura, CA 93003 Phone 805.486.4565 Fax 858.712.2040 Email: info@slpower.com www.slpower.com