Signal Relays AXICOM P2 Relay V23079 n Standard telecom relay (ringing and test access) n Slim line 15x7.5mm (.590x.295”) n Max. switching current 5A n 2 form C bifurcated contacts (2 changeover contacts, 2 CO) n Immersion cleanable n High sensitivity for low power consumption 140mW/ 70mW n Single coil version with surge voltage resistance between contact and coil: 2.5kV (2/10μs) meets the Telcordia Requirement GR-1089, 1.5kV (10/160μs) meets FCC Part 68 Typical applications AXICOM Communications equipment linecard application (ringing and test access), Telecom-, Signal and RF Relays 108-98002 Rev. E PABX, voice over IP, office equipment, measurement and control equipment, automotive equipment as CAN bus, keyless entry, speaker switch, medical P2 V23079 Relay Z equipment, consumer electronics, set top boxes, HiFi Coil Operating Range Approvals Coil Data UL 508 File No. E 111441, UL 60950, Magnetic system polarized IEC/EN60950 IEC Ref. Cert. No. 327 Coil voltage range 2 to 24VDC 3.4 70 mW Technical data of approved types on request Max. coil temperature 125°C U = Nominal coil voltage 3.2 nom 3 Thermal resistance < 125K/W Umax. at 0 A 2.8 Umax. at 2 x 1 A U = Upper limit of the operative range of Contact Data max. 2.6 Umax. at 2 x 2 A Contact arrangement 2 form C (CO) Coil versions, monostable the coil voltage (limiting voltage) when coils are 2.4 Max. switching voltage 220VDC, 250VAC Coil Rated Operate Limiting Release Coil Rated coil 2.2 continously energized Rated current 2A code voltage voltage Voltage voltage resistance power 2 Limiting continuous current, 85°C 2A 1.8VDC VDC VDC VDC Ω±10% mW U = Lower limit of the operative range of op. min. 1.6 Switching Power 60W, 62.5VA 008 3.00 2.25 6.50 0.30 64 140 the coil voltage (reliable operate voltage) 1.4 Contact material AgNi, gold-covered 016 4.00 3.00 8.70 0.40 114 140 1.2 Contact style bifurcated contact 011 4.50 3.38 9.80 0.45 145 140 Unom. nominal coil voltage 1 For latching relays U resp. U set min. reset min. Minimum switching voltage 100μV 001 5.00 3.75 10.90 0.50 178 140 0.8 Uop. min. Thermoelectrical potential <10µV 002 0.66.00 4.50 13.00 0.60 257 140 U = Lower limit of the operative range of rel. min. 0.4 Initial contact resistance <50mΩ at 10mA, 20mV 006 9.00 6.75 19.60 0.90 578 140 the coil voltage (reliable release voltage) 0.2 Frequency of operation, without load 50 operations/s 003 12.00 9.00 26.15 1.20 1029 140 0 Operate time typ. 2ms, max. 4ms 005* 24.00 18.00 52.30 2.40 4114 140 -40-30 -20-10 0102030405060708090 100 110 120 130 140 Set/reset time typ. 2ms, max. 4ms All figures are given for coil without pre-energization, at ambient temperature +23°C. Ambient Temperature [°C] Other coil voltages on request. Release time * Available only in standard coil configurations without diode in parallel typ. 2ms, max. 4ms with diode in parallel typ. 4ms, max. 6ms 2.8 140 mW Bounce time typ. 1ms, max. 3ms 2.6 Umax. at 0 A Electrical endurance 2.4 Umax. at 2 x 1 A 7 at 12V / 10mA typ. 5x10 operations Umax. at 2 x 2 A 2.2 7 at 6V / 100mA typ. 1x10 operations 2 5 at 60V / 500mA typ. 5x10 operations 1.8 6 at 30V / 1000mA typ. 1x10 operations 1.6 5 at 30V / 2000mA typ. 2x10 operations 1.4 Contact ratings, UL 110VDC / 0.3A - 33W 1.2 30VDC / 2.0A - 60W Unom. nominal coil voltage 1 120VAC / 0.5A - 60VA 0.8 240VAC / 0.25A -60VA 0.6 125VAC / 1A NO Side Uop. min. 0.4 Urel. min. 125VDC / 0.5A NO Side 0.2 6 Mechanical endurance typ. 100x10 operations 0 Max. DC load breaking capacity -40-30 -20-10 0102030405060708090 100 110 120 130 140 Ambient Temperature [°C] 200 mW 2.8 2.6 Umax. at 0 A Umax. at 2 x 1 A 2.4 Umax. at 2 x 2 A 2.2 2 1.8 1.6 1.4 1.2 DC current [A] Unom. nominal coil voltage 1 0.8 1 0.6 Uop. min. 05-2018, Rev.0518 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- 0.4 www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, applica Ution notes and all specifica rel. min. tions 0.2 © 2015 Tyco Electronics Corporation, only together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company http://relays.te.com/definitions 0 -40-30 -20-10 0102030405060708090 100 110 120 130 140 Ambient Temperature [°C] All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 15 DC voltage [VDC] Coil Voltage [U/Unom] Coil Voltage [U/Unom] Coil Voltage [U/Unom] Signal Relays AXICOM P2 Relay V23079 (Continued) Coil Data (continued) Insulation Data Standard HDV Initial dielectric strength Coil versions, bistable between open contacts 1000V 1500V rms rms Coil Rated Set Limiting Reset Coil Rated coil between contact and coil 1500V 1500V rms rms code voltage voltage Voltage voltage resistance power between adjacent contacts 1000 V 1500V rms rms VDC VDC VDC VDC Ω±10% mW Initial surge withstand voltage Bistable, 1 coil according to Telcordia TR-NWT-001089 (2/10μs) AXICOM 108 3.00 2.25 9.2 -2.25 128 70 between open contacts 2000V 2500V Telecom-, Signal and RF Relays 108-98002 Rev. E 111 4.50 3.38 13.85 -3.38 289 70 between contact and coil 2500V 2500V 101 5.00 3.75 15.33 -3.75 357 70 between adjacent contacts 2500V 2500V P2 V23079 Relay 102 6.00 4.50 18.5 -4.50 514 70 according to (10/700 μs IEC 60950) 106 9.00 6.75 27.75 -6.75 1157 70 between open contacts 2000V 2500V 103 12.00 9.00 37 -9.00 2057 70 between contact and coil 2500V 2500V 105* Coil Ope 24.00 ra18.00 ting Range 74 -18.00 8228 70 between adjacent contacts 2500V 2500V 9 Bistable, 2 coil Initial insulation resistance at 500 Vdc > 10 Ω 219 2.00 1.50 4.33 1.50 28 140 Capacitance 3.4 218 2.40 1.80 5.2 1.80 41 140 between open contacts max. 1pF 70 mW U = Nominal coil voltage 3.2 nom 208 3.00 2.25 6.5 2.25 64 140 between contact and coil max. 2pF AXICOM 3 Umax. at 0 A 211 4.50 3.38 9.8 3.38 145 140 between adjacent contacts max. 1.5pF 2.8 Telecom-, Signal and RF Relays U = Upper limit of the operative range of Umax. at 2 x 1 A 108-98002 Rev. E max. 201 5.00 3.75 10.9 3.75 178 140 Clearance /creepage 2.6 Umax. at 2 x 2 A the coil voltage (limiting voltage) when coils are 202 2.6.00 4 4.50 13 4.50 257 140 according to IEC / EN 60950 1.3/2.5mm P2 V23079 Relay 2.2 continously energized 206 9.00 6.75 19.6 6.75 578 140 2 203 12.00 9.00 26.15 9.00 1029 140 1.8 U = Lower limit of the operative range of 205* 24.00 18.00 52.3 18.00 4114 140 op. min. Other Data 1.6 Coil Operating Range All figures are given for coil without pre-energization, at ambient temperature +23°C. the coil voltage (reliable operate voltage) 1.4 Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content Other coil voltages on request. 1.2 refer to the Product Compliance Support Center at Unom. nominal coil voltage * Available only in standar 1 d coil configurations For latching relays U resp. U www set min. .te.com/customersupport/r reset min. ohssupportcenter 3.4 0.8 70 mW Ambient temperature -40 to +85°C U = Nominal coil voltage 3.2 Uop. min. nom 0.6 U = Lower limit of the operative range of rel. min. 3 Category of environmental protection Umax. at 0 A 0.4 2.8 U = Upper limit of the operative range of Umax. at 2 x 1 A IEC 61810 the coil voltage (reliable release voltage) RT III - wash tight 0.2 max. 2.6 Umax. at 2 x 2 A 0 Vibration resistance (functional) 35g, 10 to 1000Hz the coil voltage (limiting voltage) when coils are 2.4 -40-30 -20-10 0102030405060708090 100 110 120 130 140 Shock resistance (functional) 2.2 continously energized Ambient Temperature [°C] 2 IEC 60068-2-27 (half sine) 100g 1.8 Terminal type PCB-THT, U = Lower limit of the operative range of op. min. 1.6 SMT long and short terminals the coil voltage (reliable operate voltage) 1.4 2.8 Weight max. 2.8 g 140 mW 1.2 2. U 6 nom. nominal coil voltage 1 Resistance to soldering heat THT For latching relays U resp. U Umax. at 0 A set min. reset min. 0.8 2.4 Umax. at 2 x 1 A IEC 60068-2-20 265°C/10s Uop. min. 0.6 Umax. at 2 x 2 A U = Lower limit of the operative range of 2.2 Moisture sensitive level, JEDEC J-Std-020D MSL3 rel. min. 0.4 2 related only to SMT relays the coil voltage (reliable release voltage) 0.2 0 1.8 packed in orginal dry-packs -40-30 -20-10 0102030405060708090 100 110 120 130 140 1.6 Ultrasonic cleaning not recommended Ambient Temperature [°C] Packaging/unit 1.4 Coil versions, high dielectric version, monostable, overmolded THT box/2000 pcs. 1.2 Unom. nominal coil voltage Coil Rated 1 Operate Limiting Release Coil Rated coil SMT reel/2000 pcs. or 2500 pcs. 2.8 140 mW code voltage 0.8 voltage Voltage Voltage resistance power 2.6 Umax. at 0 A VDC 0.6 VDC VDC VDC Ω±10% mW Uop. min. 2.4 Umax. at 2 x 1 A 008 3.00 0.4 2.25 6.1 0.30 45 200 Urel. min. Umax. at 2 x 2 A 2.2 001 5.00 3.75 10.1 0.50 125 200 0.2 2 002 6.00 4.50 12.1 0.60 180 200 0 1.8 -40-30 -20-10 0102030405060708090 100 110 120 130 140 006 9.00 6.75 18.2 0.90 405 200 1.6 Ambient Temperature [°C] 003 12.00 9.00 24.2 1.20 720 200 1.4 All figures are given for coil without pre-energization, at ambient temperature +23°C. 1.2 Other coil voltages on request. Unom. nominal coil voltage 1 200 mW 0.8 2.8 0.6 Uop. min. 2.6 Umax. at 0 A 0.4 Urel. min. Umax. at 2 x 1 A 2.4 0.2 Umax. at 2 x 2 A 2.2 0 2 -40-30 -20-10 0102030405060708090 100 110 120 130 140 Ambient Temperature [°C] 1.8 1.6 1.4 1.2 200 mW 2.8 Unom. nominal coil voltage 1 2.6 Umax. at 0 A 0.8 Umax. at 2 x 1 A 2.4 0.6 Uop. min. Umax. at 2 x 2 A 2.2 0.4 Urel. min. 2 0.2 1.8 0 1.6 -40-30 -20-10 0102030405060708090 100 110 120 130 140 1.4 Ambient Temperature [°C] 1.2 2 Unom. nominal coil voltage 1 05-2018, Rev. 0518 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- 0.8 www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications 0.6 © 2015 Tyco Electronics Corporation, only together with the Uop. min. ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. 0.4 All specifications subject to change. Consult T U yco Electronics for latest specifications. rel. min. 5 of 15 a TE Connectivity Ltd. company http://relays.te.com/definitions 0.2 0 -40-30 -20-10 0102030405060708090 100 110 120 130 140 Ambient Temperature [°C] All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 15 Coil Voltage [U/Unom] Coil Voltage [U/Unom] Coil Voltage [U/Unom] Coil Voltage [U/Unom] Coil Voltage [U/Unom] Coil Voltage [U/Unom] Signal Relays AXICOM P2 Relay V23079 (Continued) Terminal assignment TOP view on component side of PCB Monostable version Bistable version, 1-coil Bistable version, 2-coils Contacts are shown in reset condition. Both coils can be used as either set or reset coils. Contact position might change during transportation and must be reset before use. PCB layout TOP view on component side of PCB THT version SMT, long terminals SMT, short terminals 0,9 ±0,1 Dimensions Standard coil 14.5±0.1 7.2±0.1 14.5±0.1 7.2±0.1 14.5±0.1 7.2±0.1 THT version SMT, long terminals SMT, short terminals 14.5±0.1 7.2±0.1 14.5±0.1 7.2±0.1 14.5±0.1 7.2±0.1 0.5±0.05 5.52±0.15 5.52 0.5±0.05 0.5±0.05 9.4±0.15 7.4±0.15 0.5±0.05 5.52±0.15 0.5±0.05 5.52 0.5±0.05 9.4±0.15 7.4±0.15 Overmolded coil, high dielectric version THT version SMT, long terminals SMT, short terminals 14.6±0.1 7.2±0.1 14.6±0.1 7.2±0.1 14.6±0.1 7.2±0.1 14.6±0.1 7.2±0.1 14.6±0.1 7.2±0.1 14.6±0.1 7.2±0.1 0.5±0.05 5.52 0.5±0.05 5.52 0.5±0.05 9.4±0.15 7.4±0.15 0.5±0.05 5.52 5.52 0.5±0.05 0.5±0.05 9.4±0.15 7.4±0.15 3 05-2018, Rev.0518 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications © 2015 Tyco Electronics Corporation, only together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company http://relays.te.com/definitions 0.45 0.45 0.55-0.15 0.55-0.15 9.5±0.19.5±0.1 9.8±0.19.8±0.1 3.25-0.25 3.25-0.25 3.25-0.25 3.25-0.25 9.9±0.1 9.9±0.1 10.4±0.15 10.4±0.15 9.9±0.15 9.9±0.15 10.4±0.15 10.4±0.15 Signal Relays AXICOM P2 Relay V23079 (Continued) Processing Recommended soldering conditions Vapour phase soldering 20 to 40s full line: typical dotted line: process limits 240°C 180°C forced cooling 130°C external preheating 100°C Vapour phase soldering temperature/time profile (lead and housing peak temp.) Time [s] Recommended reflow soldering profile Infrared soldering temperature/time profile (lead and housing peak temp.) Time [s] Packing Reel dimensions 4 05-2018, Rev. 0518 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications © 2015 Tyco Electronics Corporation, only together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company http://relays.te.com/definitions Temperature [°C] Temperature [°C] max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° max. 3° Signal Relays AXICOM P2 Relay V23079 (Continued) USED ON - A-A USED ON - D A-A A 4±0.2 A D A 4±0.2 2:1 A 10±0.2 12±0.2 12.2±0.2 2:1 10±0.2 12.2±0.2 12±0.2 roztec transportnich otvoru 1.5 C distance of transport holes 1.5 B (8) (48) 4x10=40±0.2mm roztec transportnich otvoru 1.5 C B distance of transport holes 1.5 1.5 0.1 ( 1.5) 4x11=44±0.2mm 4±0.1 2±0.1 (8) (48) 2:1 4x10=40±0.2mm 4x12=48±0.2mm 1.5 0.1 ( 1.5) 4x11=44±0.2mm 4±0.1 2±0.1 2:1 4x12=48±0.2mm USED ON - B-B B-B A-A USED ON - D A-A A USED ON B B - 4±0.2 A A-A D 2:1 10±0.2 D 4±0.2 +0.2 12±0.2 12.2±0.2 1.2 0 +0.2 1.2 0 4±0.2 B 16±0.15 1.5 0.1 DWN 30.3.2012 MATERIAL HEAT TREAT 2:1 -9 roztec transportnich otvoru 1.5 PS conductivity 10 S/m - Zdenek Curda 8±0.2 2:1 C B distance of transport holes 1.5 - B CHK (8) (48) 1.5 0.1 - 16±0.15 DIMENSIONS: TOLERANCES UNLESS DWN MATERIAL HEAT TREAT A OTHERWISE SPECIFIED: 30.3.2012 4x10=40±0.2mm 2:1 - -9 9±0.2 9.1±0.2 PS conductivity 10 S/m 8±0.2 mm 2:1 - Zdenek Curda 1.5 0.1 ( 1.5) 4x11=44±0.2mm - 30.03.2012 ZC PH APVD 30.3.2012 TE Connectivity 4±0.1 2±0.1 3 0 PLC - 2:1 - LOC CHK 1 PLC 0.1 Petr Hofman - 4x12=48±0.2mm 9±0.2 9.1±0.2 DIMENSIONS: TOLERANCES UNLESS A roztec transportnich otvoru 2 PLC 0.01 1.5 2 - 17.06.2011 PH 9122 OTHERWISE SPECIFIED: NAME 1.5 0.1 3 PLC 0.001 - - B mm distance of transport holes 4 PLC 0.0001 1.5 APVD P2L3 - Blister tape long terminals TE Connectivity USED ON DIST 3 - 1 - 30.03.2012 ZC 25.05.1998 PH roztec transportnich otvoru PH 9122 ANGLES - 1.5 30.3.2012 0 PLC - 1.5 0.1 4x10=40±0.2mm SCALE SIZE DRAWING NO SHEET REV C - LOC B B-B P LTR REVISION RECORD DATE distance of transport holes DWN APVD 1 PLC - 1.5 0.1 Petr Hofman OF 4±0.1 2±0.1 SURFACE TEXTURE 4:1 C23303-A079-C121 1 1 3 - 0.01 A3 - 17.06.2011 PH 9122 2 PLC 4x11=44±0.2mm 2 4x10=40±0.2mm NAME C - 3306-7 (3/11) 3 PLC 0.001 4±0.1 2±0.1 8 7 4x11=44±0.2mm 4 PLC 4x12=48±0.2mm 0.0001 6 5 4 P2L3 - Blister tape long terminals 3 2 1 DIST 1 - 25.05.1998 PH 9122 ANGLES - 4x12=48±0.2mm A-A SCALE SIZE DRAWING NO SHEET REV P LTR REVISION RECORD DATE DWN APVD - OF SURFACE TEXTURE - 4:1 C23303-A079-C121 1 1 3 A3 B-B 3306-7 (3/11) B-B 8 7 6 5 4 3 2 1 B D A A 4±0.2 B B +0.2 1.2 0 A A B 2:1 16±0.15 1.5 0.1 DWN MATERIAL HEAT TREAT 30.3.2012 +0.2 -9 8±0.2 PS conductivity 10 S/m - 2:1 1.2 0 Zdenek Curda +0.2 - 1.2 CHK 0 - TOLERANCES UNLESS DIMENSIONS: A OTHERWISE SPECIFIED: - 1.5 0.1 9±0.2 9.1±0.2 mm 30.03.2012 APVD 30.3.2012 TE Connectivity 3 - ZC PH 0 PLC - B 1.5 0.1 LOC 12±0.15 1 PLC 0.1 Petr Hofman DWN MATERIAL HEAT TREAT 17.06.2011 2 PLC 0.01 26.3.2012 -9 2 - PH 9122 roztec transportnich otvoru NAME PS conductivity 10 S/m - 3 PLC 0.001 1.5 B - 12±0.15 Zdenek Curda 1.5 0.1 4 PLC 0.0001 - P2L3 - Blister tape long terminals CHK DWN MATERIAL HEAT TREAT DIST B 25.05.1998 - - 26.3.2012 -9 1 - PH 9122 ANGLES distance of transport holes 1.5 DIMENSIONS: TOLERANCES UNLESS A S/m SCALE SIZE DRAWING NO SHEET REV PS conductivity 10 - OTHERWISE SPECIFIED: Zdenek Curda OF - P LTR REVISION RECORD DATE DWN APVD - SURFACE TEXTURE 4:1 C23303-A079-C121 1 1 3 mm - - 4x10=40±0.2mm A3 APVD CHK C 8 - 26.3.2012 ZC PH 26.3.2012 TE Connectivity - 0 PLC - TOLERANCES UNLESS 3306-7 (3/11) LOC DIMENSIONS: A 1 PLC 0.1 Petr Hofman OTHERWISE SPECIFIED: 4±0.1 2±0.1 - 8 7 6 5 4x11=44±0.2mm 4 3 2 - 13.12.2005 9193 9121 2 PLC 0.01 mm 1 7 NAME - 3 PLC 0.001 APVD TE Connectivity 8 - 26.3.2012 ZC PH 26.3.2012 0.0001 0 PLC - 4 PLC 4x12=48±0.2mm LOC P2L2/P2L3/FU2 - Blister tape short terminals DIST 1 - 25.05.1998 9188 9151 ANGLES - 1 PLC 0.1 Petr Hofman SCALE SIZE DRAWING NO SHEET REV 2 PLC 0.01 7 - 13.12.2005 9193 9121 OF P LTR REVISION RECORD DATE DWN APVD - NAME - - SURFACE TEXTURE 4:1 3 PLC C23303-A079-C120 0.001 1 1 8 A3 4 PLC 0.0001 3306-7 (3/11) P2L2/P2L3/FU2 - Blister tape short terminals DIST - 25.05.1998 9188 9151 - 1 ANGLES 8 7 SCALE SIZE DRAWING NO SHEET REV 6 5 4 3 2 1 OF B-B P LTR REVISION RECORD DATE DWN APVD - SURFACE TEXTURE C23303-A079-C120 1 1 - 4:1 A3 8 3306-7 (3/11) 8 7 6 5 4 3 2 1 A B A +0.2 1.2 0 1.5 0.1 B 12±0.15 DWN MATERIAL HEAT TREAT 26.3.2012 -9 PS conductivity 10 S/m - Zdenek Curda - CHK - DIMENSIONS: TOLERANCES UNLESS A OTHERWISE SPECIFIED: - mm APVD TE Connectivity 8 - 26.3.2012 ZC PH 26.3.2012 0 PLC - LOC 1 PLC 0.1 Petr Hofman 13.12.2005 2 PLC 0.01 7 - 9193 9121 NAME - 3 PLC 0.001 4 PLC 0.0001 P2L2/P2L3/FU2 - Blister tape short terminals DIST - 25.05.1998 9188 9151 - 1 ANGLES SCALE SIZE DRAWING NO SHEET REV OF P LTR REVISION RECORD DATE DWN APVD - SURFACE TEXTURE 1 1 - 4:1 C23303-A079-C120 8 A3 3306-7 (3/11) 8 7 6 5 4 3 2 1 5 05-2018, Rev.0518 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications © 2015 Tyco Electronics Corporation, only together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company http://relays.te.com/definitions max. R0.3 max. R0.3 max. R0.3 max. R0.3 max. R0.3 max. R0.3 max. 3° max. 3° max. 3° max. R0.3 max. R0.3 max. R0.3 max. R0.3 max. R0.3 max. R0.3 max. max. 3° 3° max. 3° max. 3° max. 3° max. 3° THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT DWG NO AUTHORIZATION FROM TE (www.TE.com). THIS DRAWING IS A CONTROLLED DOCUMENT C23303-A079-C121 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES +0.3 AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, 24±0.3 10.4 0 OTHER THAN TE PERSONNEL, WITHOUT DWG NO AUTHORIZATION FROM TE (www.TE.com). THIS DRAWING IS A CONTROLLED DOCUMENT C23303-A079-C120 11.5±0.1 1.75±0.1 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES OTHER THAN TE PERSONNEL, WITHOUT AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, DWG NO AUTHORIZATION FROM TE (www.TE.com). OTHER THAN TE PERSONNEL, WITHOUT THIS DRAWING IS A CONTROLLED DOCUMENT DWG NO AUTHORIZATION FROM TE (www.TE.com). THIS DRAWING IS A CONTROLLED DOCUMENT C23303-A079-C120 C23303-A079-C121 +0.3 24±0.3 24±0.3 10.4 0 11.5±0.1 1.75±0.1 11.5±0.1 1.75±0.1 +0.3 10.9 0 24±0.3 +0.3 11.5±0.1 1.75±0.1 10.9 0 0.6 15.4±0.2 0.6 1.3±0.2 2.2±0.2 0.6 0.6 15.4±0.2 15.4±0.2 15.4±0.2 1.3±0.2 1.3±0.2 1.3±0.2 2.2±0.2 2.2±0.2 2.2±0.2 (3.6) (3.6) 1.9±0.2 1.9±0.2 4.5±0.2 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT DWG NO AUTHORIZATION FROM TE (www.TE.com). THIS DRAWING IS A CONTROLLED DOCUMENT (3.6) (3.6) C23303-A079-C120 (3.6) (3.6) (3.6) (3.6) 1.9±0.2 1.9±0.2 1.9±0.2 1.9±0.2 1.9±0.2 1.9±0.2 4.4±0.2 4.5±0.2 4.4±0.2 THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE, OTHER THAN TE PERSONNEL, WITHOUT DWG NO AUTHORIZATION FROM TE (www.TE.com). THIS DRAWING IS A CONTROLLED DOCUMENT 24±0.3 C23303-A079-C121 +0.3 24±0.3 10.4 0 +0.3 11.5±0.1 1.75±0.1 11.5±0.1 1.75±0.1 10.9 0 0.6 0.6 15.4±0.2 15.4±0.2 1.3±0.2 1.3±0.2 2.2±0.2 2.2±0.2 (3.6) (3.6) 1.9±0.2 1.9±0.2 4.4±0.2 (3.6) (3.6) 1.9±0.2 1.9±0.2 4.5±0.2 Signal Relays AXICOM P2 Relay V23079 (Continued) Product code structure Typical product code V23079 A 1 001 B 301 Type V23079 Signal Relay P2 Series Version A THT, monostable D SMT, monostable, long term. G SMT, monostable, short term. B THT, latching, 2 coils E SMT, latching, 2 coils long term. H SMT, latching, 2 coils short term. C THT, latching, 1 coil F SMT, latching, 1 coil long term. J SMT, latching, 1 coil short term. Coil design 1 Standard coil (not for high dielectric version) 2 Overmolded coil Coil Coil code: please refer to coil versions table Version B Standard version X High dielectric version Contacts for standard versions 301 2 form C contacts (2 CO), AgNi +Au 201 2 form C contacts (2 CO), AgPd +Au; on request only Contacts for dielectric versions X07* 2 form C contacts (2 CO), AgNi +Au Product code Version Coil design Coil type Coil voltage Part number V23079-A1006-B301 9VDC 2-1393788-0 V23079-A1005-B301 24VDC 1-1393788-6 V23079-A2008-B301 Overmolded 3VDC 6-1419120-6 V23079-A2011-B301 4.5VDC 3-1393789-9 V23079-A2001-B301 5VDC 3-1393789-5 V23079-A2002-B301 6VDC 3-1393789-6 V23079-A2006-B301 9VDC 3-1393789-8 V23079-A2003-B301 12VDC 3-1393789-7 V23079-B1218-B301 Standard Bistable, 2 coils 2.4VDC 1422002-8 V23079-B1208-B301 3VDC 4-1393788-1 V23079-B1211-B301 4.5VDC 4-1393788-2 V23079-B1201-B301 5VDC 3-1393788-3 V23079-B1202-B301 6VDC 3-1393788-5 V23079-B1206-B301 9VDC 3-1393788-9 V23079-B1203-B301 12VDC 3-1393788-6 V23079-B1205-B301 24VDC 3-1393788-7 V23079-B2219-B301 Overmolded 2VDC 1-1422002-2 V23079-B2218-B301 2.4VDC 1-1422002-1 V23079-B2208-B301 3VDC 1-1422002-0 V23079-B2201-B301 5VDC 1422002-9 V23079-C1108-B301 Standard Bistable, 1 coils 3VDC 5-1393788-3 V23079-C1111-B301 4.5VDC 5-1393788-4 V23079-C1101-B301 5VDC 4-1393788-5 V23079-C1102-B301 6VDC 4-1393788-7 V23079-C1106-B301 9VDC 5-1393788-1 V23079-C1103-B301 12VDC 4-1393788-8 V23079-C1105-B301 24VDC 5-1393788-0 6 05-2018, Rev. 0518 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications © 2015 Tyco Electronics Corporation, only together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company http://relays.te.com/definitions Signal Relays AXICOM P2 Relay V23079 (Continued) Product code Version Coil design Coil type Coil voltage Part number V23079-D1006-B301 9VDC 5-1393788-9 V23079-D1005-B301 24VDC 5-1393788-8 V23079-D2008-B301 Overmolded 3VDC 4-1393789-7 V23079-D2011-B301 4.5VDC 4-1393789-8 V23079-D2001-B301 5VDC 4-1393789-3 V23079-D2002-B301 6VDC 4-1393789-4 V23079-D2006-B301 9VDC 4-1393789-6 V23079-D2003-B301 12VDC 4-1393789-5 V23079-E1219-B301 2VDC 1-1422007-0 Standard Bistable, 2 coils V23079-E1218-B301 2.4VDC 1422007-5 V23079-E1208-B301 3VDC 7-1393788-1 V23079-E1211-B301 4.5VDC 7-1393788-2 V23079-E1201-B301 5VDC 6-1393788-8 V23079-E1202-B301 6VDC 1393789-5 V23079-E1206-B301 9VDC 1393789-9 V23079-E1203-B301 12VDC 6-1393788-9 V23079-E1205-B301 24VDC 7-1393788-0 1422007-6 V23079-E2219-B301 Overmolded 2VDC V23079-E2201-B301 5VDC 1422007-7 V23079-E2208-B301 3VDC 1422007-8 V23079-E2218-B301 2.4VDC 1422007-9 V23079-F1108-B301 Standard Bistable, 1 coil 3VDC 7-1393788-5 V23079-F1111-B301 4.5VDC 1-1393789-4 V23079-F1101-B301 5VDC 7-1393788-3 V23079-F1102-B301 6VDC 1-1393789-0 1-1393789-2 V23079-F1106-B301 9VDC V23079-F1103-B301 12VDC 7-1393788-4 V23079-F1105-B301 24VDC 1-1393789-1 V23079-G1005-B301 SMT, short pins Monostable 24VDC 7-1393788-8 V23079-G2008-B301 Overmolded 3VDC 5-1393789-4 V23079-G2016-B301 4VDC 1393790-5 V23079-G2011-B301 4.5VDC 5-1393789-5 V23079-G2001-B301 5VDC 4-1393789-9 V23079-G2002-B301 6VDC 5-1393789-0 V23079-G2006-B301 9VDC 5-1393789-3 V23079-G2003-B301 12VDC 5-1393789-1 V23079-H1208-B301 3VDC 2-1393789-4 Standard Bistable, 2 coils V23079-H1211-B301 4.5VDC 8-1393788-4 V23079-H1201-B301 5VDC 2-1393789-0 V23079-H1202-B301 6VDC 2-1393789-1 V23079-H1206-B301 9VDC 2-1393789-3 V23079-H1203-B301 12VDC 8-1393788-3 V23079-H1205-B301 24VDC 2-1393789-2 V23079-J1108-B301 Bistable, 1 coil 3VDC 2-1393789-9 V23079-J1111-B301 4.5VDC 3-1393789-0 V23079-J1101-B301 5VDC 2-1393789-5 V23079-J1102-B301 6VDC 2-1393789-6 V23079-J1103-B301 12VDC 2-1393789-7 V23079-J1105-B301 24VDC 2-1393789-8 V23079-G2008-X079 High dielectric Monostable 3VDC 1422006-5 V23079-G2001-X071 Overmolded 5VDC 1422006-1 V23079-G2002-X072 6VDC 1422006-2 V23079-G2006-X073 9VDC 1422006-3 V23079-G2003-X074 12VDC 1422006-4 V23079-A2003-X074 12VDC 1422025-7 V23079-A2008-X079 3VDC 1-1422025-1 7 05-2018, Rev.0518 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, ‘Definitions’ sec- www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications © 2015 Tyco Electronics Corporation, only together with the ‘Definitions’ section. the ‘Definitions’ section, available at are subject to change. a TE Connectivity Ltd. company http://relays.te.com/definitions