PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver Product Facts ■ Complies with IEEE Standard 802.3z Gigabit Ethernet 1000BASE-SX PMD requirements ■ Complies with Small Form-factor Pluggable (SFP) Multi-Source Agreement (MSA) ■ High density MT-RJ connector interface ■ Operates to 550 m with 50/125 µm or 275 m with 62.5/125 µm fiber ■ Hot Pluggable ■ Single +3.3-volt power supply ■ PECL and LVPECL AC-coupled data Interface ■ Transmitter uses 850nm vertical cavity surface emitting laser (VCSEL) ■ Class 1 Laser Safe per FDA/CDRH and IEC 60825-1 ■ UL 60950 recognized Tyco Electronics, recognizing the multimode optical fibers. The ■ Compatible with standard Gigabit market need for higher optical port module, which operates from a Ethernet chipsets. density, is developing an entire single +3.3V power supply, contains ■ Units are supplied with dust plugs product platform of Tyco Electronics’ separate AC-coupled transmitter ■ Mates to MSA compliant Host Small Form-factor Pluggable (SFP) and receiver sections that have Connector and Cage Assembly transceivers with the popular MT-RJ PECL/LVPECL compatible data connector. These transceivers are interfaces. Tyco Electronics also Applications less than half the width of the offers a wide variety of Small Form functionally similar GBICs and simply Factor (SFF) and Small Form-factor ■ Switches plug into a SFP compatible surface Pluggable (SFP) transceivers for ■ Repeaters mount connector and cage on the both singlemode and multimode ■ Network Interface cards customer board. The smaller size applications. ■ Hubs and 0.64-inch port-to-port centerline spacing enables equipment The Tyco Electronics’ Gigabit ■ Routers manufacturers to cost-effectively Ethernet SFP MT-RJ Transceiver double the fiber optic port density has been extensively tested to of a given product. comply with the Gigabit Ethernet industry standard. The VCSEL- The Tyco Electronics’ Gigabit based transmitter is certified to be Ethernet SFP MT-RJ Transceiver Class 1 laser safe, as defined by 1382350-1 is a short wavelength U.S. and international standards. fiber optic transceiver module for The module has been designed use in 1.25 Gb/s Gigabit Ethernet with grounding and shielding and high-speed proprietary link features that minimize EMI applications. The transceiver sends susceptibility and radiated emis- and receives pre-encoded data sions. Units are supplied with over a pair of 62.5µm or 50µm core dust plugs. Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 1 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Gigabit Ethernet Multimode Transmitter Performance Specifications: SFP MT-RJ Transceiver (T =0 to 70°C, V -V =3.135 to 3.465V DC) C CC EE Parameter Symbol Notes Min Typ Max Units Operating Data Rate – – 1.25 Gb/s Part Number 1382350-1 Optical Output (avg.) P 1,2 -9.5 – -4 dBm OUT Extinction Ratio – 3 9 – – dB Transmit Disabled P – – – -30 dBm OUT DIS Optical Output (avg.) Center Wavelength λ 4 770 845 860 nm OUT Spectral Width (RMS) ∆λ 4 – – 0.85 nm Relative Intensity Noise RIN 5 – -117 dB/Hz 12 Deterministic Jitter DJ 6 – – 80 ps Total Jitter TJ 6 – – 227 ps Output Rise Time t 7,8 – – 260 ps TLH Output Fall Time t 7,8 – – 260 ps THL Pk-Pk Differential Input V 9 500 – 2000 mV DIFF Voltage Transmit Fault Voltage Levels Tx_Fault_On 10 2 – V +.3 V CC Tx_Fault_Off 10 0 – 0.8 V Transmit Disable Voltage Levels Tx Disabled – 2.0 – 3.465 V Tx Enabled – 0 – 0.8 V Power Supply Voltage V - V – 3.135 3.3 3.465 V CC EE Supply Current I ––– 60 mA CC Operating Temperature T –0– 70 °C C Note: All optical measurements made through a short patch cable, between 2 and 5 meters in length, using 62.5 µm multimode fiber unless stated otherwise. 1. Meets Class 1 laser safety requirements of IEC 60825-1 and IEC 60825-2 and U.S. Department of Health Services 21 CFR 1040.10 and 1040.11 when operated within the specified temperature and power supply ranges. 2. Transmitter optical output power measured per TIA/EIA 455-95. Transmitter modulated with a valid 8b/10b data pattern. Specification applies for both 50 µm and 62.5 µm core multimode fiber. 3. Extinction ratio measured per TIA/EIA 526-4A with a repeating K28.7 data pattern. 4. Center wavelength and spectral width measured per TIA/EIA 455-127 using optical spectrum analyzer with a valid 8b/10b data pattern. 5. RIN measured per ANSI X.230-1994 annex A with valid 8b/10b data pattern. RF power meter and current meter test set replaced with microwave spectrum analyzer and calibrated high-speed photoreceiver. Single mode fiber in test procedure replaced with multimode patch cable. Polarization rotator omitted. 6. DJ and TJ measured per IEEE 802.3Z Gigabit Ethernet Standard. 7. Measured from 20% to 80% points on rising and falling edge of transmitted waveform. 8. Transmitter optical waveform characteristics including rise time, fall time, pulse undershoot, pulse overshoot, and ringing comply with the eye diagram shown in this document. These characteristics are controlled to help prevent excessive degradation of the receiver sensitivity. The eye mask test is performed using a receiver with a fourth-order Bessel Thompson filter. 9. Compatible with 10 K, 10 KH and 100 K ECL, PECL and LVPECL. 10. Open Collector/Drain output Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 2 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Gigabit Ethernet Multimode Receiver Performance Specifications: SFP MT-RJ Transceiver (TC=0 to 70°C, V -V =3.135 to 3.465V DC) CC EE Parameter Symbol Notes Min Typ Max Units Operating Data Rate – – 1.25 Gb/s Part Number 1382350-1 Average Receive Power P – – 0 dBm IN Receive Sensitivity 1 -17 – – dBm Stressed Receive Sensitivity 50 µm Fiber – 2 -13.5 – – dBm 62.5 µm Fiber – 2 -12.5 – – dBm Electrical 3 dB Cut-Off 3 dB f 2 – – 1.5 GHz c Optical wavelength λ – 770 – 860 nm IN Deterministic Jitter DJ 5 – – 170 ps Total Jitter TJ 5 – – 266 ps Return Loss – 3 12 – – dB Receiver Loss of Signal LOS Output Voltage Assert VA 4 2 – V + .3 V CC Deassert VD 4 0 – 0.8 V Rx LOS Power Levels (avg.) Assert P – -30 – – dBm A Deassert P – – – -17 dBm D Hysteresis – – 0.5 – – dB Power Supply Voltage V - V – 3.135 3.3 3.465 V CC EE Supply Current I – – – 100 mA CC C Operating Temperature T –0– 70 °C Note: All optical measurements made through a short patch cable, between 2 and 5 meters in length, using 62.5 µm multimode fiber unless stated otherwise. 1. Minimum average optical input power (receive sensitivity) at which the BER is less than 10E-12 measured with a 1.25 G Baud Rate 2E7 - 1 NRZ PRBS data pattern. 2. Per IEEE 802.3Z Gigabit Ethernet Standard. 3. Return loss measured per TIA/EIA 455-107. 4. This is an open drain output that should be pulled up with a 4.7K ohm - 10K ohm resistor on the host board. Pull-up voltage level should be between 2.0 V and Vcc + 0.3 V per the SFP MSA. 5. DJ and TJ measured per IEEE 802.3Z Gigabit Ethernet Standard. Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 3 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Timing Requirements of Control and Status I/O Parameter Symbol Min Max Unit Condition TX Disable Assert Time T_Off 10 µs Time from rising edge of TX Disable to when the optical output falls below 10% of nominal TX Disable Negate Time T_On 1 ms Time from falling edge of TX Disable to when the modulated optical output rises above 90% of nominal Time to initialize, including T_Init 300 ms From power on or negation of TX_Fault using reset of TX_Fault TX Disable TX_Fault Assert Time TX_Fault 100 µs Time from fault to TX-Fault on. TX Disable to reset T_Reset 10 µs Time TX Disable must be held high to reset TX-Fault LOS Assert Time T_Loss_On 100 µs Time from LOS state to LOS assert LOS Deassert Time T_Loss_Off 100 µs Time from non-LOS state to LOS deassert Serial ID Clock Rate F_Serial_Clock 100 kHz NOTE: For details on timing requirements of control and status I/O parameters, and module interface and data field descriptions, please refer to the SFP MSA, Appendix B Electrical Interface guidelines. Absolute Maximum Ratings: Parameter Symbol Units Min Max Storage Temperature T °C -40 85 S Data Input Voltage V V -0.5 V INPUT CC Differential Input Voltage V V – 2.4 DIFF Supply Voltage V -V V -0.2 5.0 CC EE Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 4 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Regulatory Compliance: Agency Test Method Listing Document FDA CDRH 21-CFR 1040 Class 1 Accession Number: 9122051-08 TUV EN60825-1:1994+A11:1996 TUV Product Services EN60825-2:1994+A1 Laser Class I EN60950:1992+A1+A2+A3+A4+A11 Protection Class III TUV Certificate Number: B020546940003 UL / UL60950 E208513 ESD Testing: Test Test Method Procedure ESD1 JEDEC/EIA JESD22-A-114-A Pulses applied to each pin and Ground at 1 KV (C=100 pF, R=1500 ohm - Human body model) ESD2 25 KV maximum air discharge 40 discharges are applied per DUT (10 at each of the top, (simulates human body discharge into nose, right, and left). Each module is tested with both a DUT) power ON and OFF All products which contain a laser must comply with government regulations for laser safety. In the U.S., the applicable standard is FDA 21 CFR 1040. In other parts of the world, IEC 60825-1 applies. These transceivers were designed and tested to the requirements of the above standards and found to be in compliance with class 1 laser safety limits. When operated within the limits specified in this document, this product conforms to IEC 60825-1: 1993 + A1 : 1997 + A2: 2001, class 1 laser product, requirements. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 5 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Pad Description: Symbol Pad # Function VEET 1 Signal Ground. Directly connect to ground. [SEE NOTE 1]. Tx_Fault 2 Transmitter Fault. This is an open collector output that should be pulled up with a 4.7K - 10KΩ resistor on the host board. [SEE NOTE 2]. Tx_Disable 3 Transmitter Disable Input. Module disables on high or open. The input is pulled up within the module with a 4.7K - 10KΩ resistor. Its states are: Low (0 - 0.8V) : Transmitter on (>0.8, <2.0V) : Undefined High (2.0 - 3.465V) : Transmitter Disabled Open: Transmitter Disabled. MOD-DEF2 4 Module Definition 2. This is the data line of two wire serial interface for serial ID. This pad should be pulled up with a 4.7K - 10KΩ resistor on the host board. [SEE NOTE 2]. MOD-DEF1 5 Module Definition 1. This is the clock line of two wire serial interface for serial ID. This pad should be pulled up with a 4.7K - 10KΩ resistor on the host board. [SEE NOTE 2]. MOD-DEF0 6 Module Definition 0. MOD-DEF0 is grounded by the module to indicate that the module is present. The pad should be pulled up with a 4.7K - 10KΩ resistor on the host board. [SEE NOTE 2]. Rate Select 7 This function is not implemented and the pad is floating. Per the SFP MSA, this is an optional input used to control the receiver bandwidth for multiple data rate operation. LOS 8 Loss of Signal. This is an open collector output that should be pulled up with a 4.7K - 10KΩ resistor on the host board. [SEE NOTE 2]. Normal operation is when LOS is Deasserted. Abnormally low receive signal level is indicated by LOS Asserted. VEER 9 Signal Ground. Directly connect to ground. [SEE NOTE 1]. VEER 10 Signal Ground. Directly connect to ground. [SEE NOTE 1]. VEER 11 Signal Ground. Directly connect to ground. [SEE NOTE 1]. RD- 12 Received Data Out Bar. Output is internally AC coupled. Use SerDes chip IC manufacturer's termination recommendation to achieve a 50 Ω termination impedance. RD+ 13 Received Data Out. Output is internally AC coupled. Use SerDes chip IC manufacturer's termination recommendation to achieve a 50 Ω termination impedance. VEER 14 Signal Ground. Directly connect to ground. [SEE NOTE 1]. VCCR 15 Receiver Power Supply. Connect as shown in the Recommended Host Board Supply Filtering Network. [SEE NOTE 3]. VCCT 16 Transmitter Power Supply. Connect as shown in the Recommended Host Board Supply Filtering Network. [SEE NOTE 3]. VEET 17 Signal Ground. Directly connect to ground. [SEE NOTE 1]. TD+ 18 Transmitter Data In. Input is internally AC coupled. There is an internal 100 Ω resistor across TD+ and TD-, which provides a 50 Ω termination for each data input. TD- 19 Transmitter Data In Bar. Input is internally AC coupled. There is an internal 100 Ω resistor across TD+ and TD-, which provides a 50 Ω termination for each data input. VEET 20 Signal Ground. Directly connect to ground. [SEE NOTE 1]. NOTE 1: Transmitter and receiver grounds are connected together inside the transceiver module. NOTE 2: Pull-up voltage between 2.0V and VccT + 0.3V NOTE 3: VCCT and VCCR are separate inside the transceiver module. Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 6 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Figure 2:Transceiver Pad Descriptions Figure 2:Transceiver Outline Descriptions Note: All dimensions are in mm. IMPORTANT: PLEASE REFER TO THE TYCO ELECTRONICS CUSTOMER DRAWING 1382350-1 FOR TRANSCEIVER HOUSING DIMENSIONS AND TOLERANCES. CALL 1-800-522-6752 FOR 24HR FAX OR ON LINE AT: http://www.tycoelectronics.com. Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 7 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Figure 4: SFP MSA Recommended Circuit Board Layout Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 8 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Figure 5: SFP MSA Recommended Bezel Opening Note: Minimum pitch illustrated. All dimensions are in mm only. Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 9 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Figure 6: Recommended Termination and Power Supply Filtering *Use SERDES IC manufacturer's termination recommendation. C1=C4 = 10 µF C2=C3=C5 = 0.1 µF Note: X7R or better MLC types are recommended for all capacitors L1=L2 = 1 µH .... 4.7 µH, max 1.0 Ω [Ferrite inductors may be used] Rup = 4.7 KΩ …. 10 KΩ NOTE: TO IMPROVE EMI,THE SIGNALS TO THE CONNECTOR SHOULD BE SHUT OFF WHEN THE TRANSCEIVER IS REMOVED. Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 10 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications. PDF Datasheet 1654843 Revised 11-03 Only available as PDF at: http://www.tycoelectronics.com/fiberoptics Gigabit Ethernet Multimode SFP MT-RJ Transceiver (Continued) Related Products: Related Documents: SFP Connector & Cage Assembly Application Specification 114-13017 Gigabit Ethernet Multimode SFP MT-RJ Transceiver Application Specification 114-13081 FOR DETAILED INFORMATION ON ALL TYCO ELECTRONICS FIBER OPTIC TRANSCEIVERS, PLEASE VISIT OUR WEB-SITE AT: http://www.tycoelectronics.com/fiberoptics Copyright 2003 by Tyco Electronics Corporation. All Rights Reserved. AMP and Tyco are trademarks. Dimensions are in millimeters with inches © (if shown) in brackets. Other products, logos, and Company names mentioned herein may be trademarks of their respective owners. 11 For drawings, technical data or samples, contact your Tyco Electronics sales engineer, call 1-800-522-6752, or visit our Website at: http://www.tycoelectronics.com/fiberoptics. Specifications subject to change. Consult Tyco Electronics for latest specifications.