SCD 44AM115+ SPECIFICATION CONTROL DRAWING Title Date Revision FIVE CONDUCTOR CABLE, SHIELDED, JACKETED, 8-15-16 G GENERAL PURPOSE, 600 VOLT This specification sheet forms a part of the latest issue of Raychem Specification 44 and NEMA WC 27500, as applicable. SHIELD - COPPER, COATING SAME AS ON CONDUCTOR, EXCEPT TIN-COATED SHIELD WITH SILVER-COATED HIGH-STRENGTH ALLOY CONDUCTOR COMPONENT WIRES - 44A011+ JACKET - RADIATION-CROSSLINKED, MODIFIED PVDF FILAMENT BINDER AS REQUIRED TABLE I. CABLE CONSTRUCTION DETAILS JACKET THICKNESS OUTSIDE DIAMETER CONDUCTOR SHIELD MAXIMUM PART NUMBER SIZE SIZE (inch) (inch) WEIGHT 1/ (AWG) (AWG) (lbs/1000 ft.) MINIMUM MAXIMUM NOMINAL MAXIMUM 44AM115+-26-* 26 38 .005 .010 .125 .142 15.0 44AM115+-24-* 24 38 .005 .010 .141 .161 19.8 44AM115+-22-* 22 38 .005 .010 .160 .183 26.0 44AM115+-20-* 20 38 .006 .012 .184 .210 35.8 44AM115+-18-* 18 38 .006 .012 .211 .242 50.1 44AM115+-16-* 16 38 .007 .014 .231 .266 61.9 44AM115+-14-* 14 38 .007 .014 .277 .319 91.0 44AM115+-12-* 12 36 .007 .014 .333 .383 139. TABLE II. CABLE PERFORMANCE DETAILS BEND TESTING MANDREL DIAMETER WEIGHT PART NUMBER (inch) (± 3%) (lb) (± 3%) 1/ IMMERSION AND COLD IMMERSION AND COLD CROSSLINKED VERIFICATION BEND CROSSLINKED VERIFICATION BEND 44AM115+-26-* 3.00 3.00 .625 3.75 44AM115+-24-* 6.00 6.00 .938 3.75 44AM115+-22-* 6.00 6.00 .938 7.50 44AM115+-20-* 6.00 6.00 .938 7.50 44AM115+-18-* 6.00 6.00 1.25 7.50 44AM115+-16-* 6.00 6.00 1.25 7.50 44AM115+-14-* 10.0 10.0 2.50 22.5 44AM115+-12-* 10.0 10.0 2.50 22.5 Nominal values are for information only. Nominal values are not requirements. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: "901/902..." MAY BE REPLACED BY "Axxx".) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Raychem Wire & Cable 501 Oakside Avenue DIMENSIONS ARE IN INCHES AND, UNLESS OTHERWISE DESIGNATED, ARE NOMINAL Page 1 of 2 Redwood City, CA 94063-3800 Phone: 1-800-522-6752 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. Fax: 1-650-361-6297 REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2006-2016 Tyco Electronics Corporation. All rights reserved. SCD Page Revision SPECIFICATION CONTROL DRAWING 2 of 2 G 44AM115+ CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level BLOCKING: 150 ± 3°C for 6 hours CROSSLINKED VERIFICATION: 200 ± 5°C for 6 hours DIELECTRIC WITHSTAND: 1500 volts (rms), 60 Hz, 15 seconds (minimum), 30 seconds (maximum) FLAMMABILITY: 30 seconds (maximum), 3 inches (maximum); no flaming of facial tissue IMMERSION: Diameter increase 5% (maximum); no cracking, no dielectric breakdown JACKET COLOR: White preferred JACKET CONCENTRICITY: 70% (minimum) JACKET ELONGATION AND TENSILE STRENGTH: Elongation, 200% (minimum) 2 Tensile Strength, 4000 lbf/in (minimum) JACKET FLAWS: Spark Test, 1.5 kV (rms) Impulse Dielectric Test, 6.0 kV (peak) LOW TEMPERATURE-COLD BEND: -55 ± 5°C for 4 hours SHIELD COVERAGE: 85% (minimum) VOLTAGE WITHSTAND (Post Environmental): 1000 volts (rms), 60 Hz, 1 minute 1/ PART NUMBER: The "+" in the part numbers in Tables I and II shall be replaced with a conductor material designator as follows: 1 tin-coated copper 2 silver-coated copper 3 nickel-coated copper 4 silver-coated high-strength copper alloy (AWG 26-16 only) 6 nickel-coated high-strength copper alloy (AWG 26-20 only) The "*" in the part numbers in Tables I and II shall be replaced by color code designators with a slash separating the component wire colors and a dash separating the component wire colors from the jacket color. Colors shown do not necessarily reflect the sequence of manufacturing. Example: AWG 20, tin-coated copper conductors; red, orange, green, blue, and white component wires; white jacket: 44AM1151-20-2/3/5/6/9-9 1 See footer section on page 1