44B413X SPECIFICATION CONTROL DRAWING TITLE Date Revision THREE CONDUCTOR CABLE, JACKETED, GENERAL PURPOSE, 600 VOLT 1-14-07 B This specification sheet forms a part of the latest issue of Raychem Specification 55A. JACKET - RADIATION-CROSSLINKED, COMPONENT WIRES - 44A011X MODIFIED ETFE CABLE CONSTRUCTION DETAILS JACKET OUTSIDE MAXIMUM CONDUCTOR THICKNESS DIAMETER PART NUMBER WEIGHT SIZE (in.) (in.) (lbs/1000 ft.) 1/ (AWG) MINIMUM NOMINAL NOMINAL MAXIMUM 44B413X-26-* 6.1 26 .006 .008 .089 .094 44B413X-24-* 24 .008 .102 .108 8.6 .006 44B413X-22-* 22 .006 .008 .118 .123 12.0 44B413X-20-* 20 .008 16.9 .006 .135 .142 44B413X-18-* 18 .008 .156 .164 24.8 .006 44B413X-16-* 30.9 16 .006 .008 .172 .180 44B413X-14-* 14 .008 .208 .219 47.0 .006 44B413X-12-* 12 .007 .009 .251 .264 72.5 CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C PART NUMBER: Maximum continuous conductor temperature The " X " in the part numbers above shall be replaced by the applicable VOLTAGE RATING: 600 volts (rms) at sea level conductor material designator as follows: ACCELERATED AGING: 300 ± 3°C for 7 hours 1 tin-coated copper BLOCKING: 150 ± 3°C for 6 hours 2 silver-coated copper DIELECTRIC WITHSTAND: 2500 volts (rms), 60 Hz, 1 minute 3 nickel-coated copper FLAMMABILITY: 3 seconds (maximum); 4 silver-coated high strength copper alloy (AWG's 26-16 only) 3 in. (maximum); no flaming of facial tissue 6 nickel-coated high strength copper alloy (AWG's 26-20 only) JACKET COLOR: White preferred JACKET ELONGATION AND TENSILE STRENGTH: The "*" in the part numbers above shall be replaced by color code Elongation, 50% (minimum) designators with a slash separating component wire colors and a 2 Tensile Strength, 5000 lbf/in (minimum) dash separating the component wire colors from the jacket color. LIFE CYCLE: 200 ± 3°C for 168 hours Colors shown do not necessarily reflect the sequence of LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours manufacturing. 1/ Example: AWG 12, tin-coated copper, black, brown and red component wires; white jacket: 44B4131-12-0/1/2-9 NOTE: Nominal values are for information only. Nominal values are not requirements. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. R Wire & Cable DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. 501 Oakside Avenue Redwood City, CA 94063-3800 Page 1 of 1 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. Phone: 1-800-227-8816 REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Fax: 1-650-361-6297 © 2007 Tyco Electronics Corporation. All rights reserved.