44B5131 SPECIFICATION CONTROL DRAWING Date Revision TITLE THREE CONDUCTOR CABLE, SPIRALLY SHIELDED, JACKETED, GENERAL PURPOSE, 600 VOLT 4-20-07 G This specification sheet forms a part of the latest issue of Raychem Specification 55A. JACKET - RADIATION-CROSSLINKED, SHIELD - TIN-COATED COPPER COMPONENT WIRES - 44A0111 MODIFIED ETFE CABLE CONSTRUCTION DETAILS JACKET THICKNESS OUTSIDE DIAMETER CONDUCTOR SHIELD MAXIMUM PART NUMBER (in.) (in.) SIZE SIZE WEIGHT 1/ (AWG) (AWG) (lbs/1000 ft.) MINIMUM NOMINAL NOMINAL MAXIMUM 44B5131-26-* 26 36 .006 .008 .100 .105 9.4 44B5131-24-* 24 36 .006 .008 .113 .119 12.4 44B5131-22-* 22 36 .006 .008 .129 .135 16.3 44B5131-20-* 20 36 .006 .008 .146 .153 22.0 44B5131-18-* 18 36 .006 .008 .167 .176 30.6 44B5131-16-* 16 36 .006 .008 .183 .192 37.4 44B5131-14-* 14 36 .007 .009 .221 .232 55.5 44B5131-12-* 12 36 .007 .009 .262 .275 82.0 CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150°C LIFE CYCLE: 200 ± 3°C for 168 hours Maximum continuous conductor temperature LOW TEMPERATURE-COLD BEND: -65 ± 2°C for 4 hours VOLTAGE RATING: 600 volts (rms) at sea level SHIELD COVERAGE: 85% (minimum) ACCELERATED AGING: 300 ± 3°C for 7 hours VOLTAGE WITHSTAND TEST (Post Environmental): BLOCKING: 150 ± 3°C for 6 hours 1000 volts (rms), 60 Hz, 1 minute DIELECTRIC WITHSTAND: 2500 volts (rms), 60 Hz, 1 minute FLAMMABILITY (Procedure 1): 3 seconds (maximum); PART NUMBER: 3 in. (maximum); no flaming of facial tissue The “*” in the part numbers above shall be replaced by color code JACKET COLOR: White preferred designators with a slash separating the component wire colors and a JACKET ELONGATION AND TENSILE STRENGTH: dash separating the component wire colors from the jacket color. Elongation, 50% (minimum) Colors shown do not necessarily reflect the sequence of manufacturing. Tensile Strength, 5000 lbf/in² (minimum) JACKET FLAWS: 1/ Example: AWG 20, black, brown and red component wires; Spark Test, 1.0 kV (rms) white jacket: 44B5131-20-0/1/2-9 Impulse Dielectric Test, 6.0 kV (peak) NOTE: Nominal values are for information only. Nominal values are not requirements. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE: “901/902...” MAY BE REPLACED BY “Axxx”.) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. R Wire & Cable DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL 501 Oakside Avenue Redwood City, CA 94063-3800 Page 1 of 1 Phone: 1-800-227-8816 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. Fax: 1-650-361-6297 REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2007 Tyco Electronics Corporation. All rights reserved.