SPECIFICATION CONTROL DRAWING 5022W0809 4-21-16 150 OHM, AWG 22, SOLID CONDUCTORS, DATA PAIR CABLE, Date: WATERTIGHT, MIL-DTL-24643/62, LSPB2SDOSW-1 CHEMINAX P Revision: THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS ELECTRICAL CHARACTERISTICS DIMENSIONS ARE NOMINAL VALUES IN INCHES, UNLESS OTHERWISE DESIGNATED. CHARACTERISTIC IMPEDANCE 150 ± 15 ohms at 0.2 to 20 MHz using IFT-TDR measurement MUTUAL CAPACITANCE 3.0 nF/100 m (maximum) at 1 kHz CONDUCTORS AWG 22, Solid, VELOCITY OF PROPAGATION 77% (nominal) .0258 Bare Copper SURFACE TRANSFER IMPEDANCE 700 milliohms/meter (maximum) DIELECTRICS (Outer Shield) at 0.1 to 100 MHz. Radiation-Crosslinked, .110 60 dB (minimum) EMP Response Foamed PE per MIL-DTL-24643. Colors - Red/Green ATTENUATION 1.0 (maximum) at 0.2 MHz FILLERS (dB/100 m) 2.5 (maximum) at 4.0 MHz Waterblocking material as 5.0 (maximum) at 16 MHz needed for watertightness 7.2 (maximum) at 31.25 MHz ADDITIONAL REQUIREMENTS WATERBLOCK LAYER ELECTRICAL .236 DRAIN WIRE CONDUCTOR RESISTANCE 16.6 ohms/1000 ft. (maximum) AWG 24, 19 Strands of (Finished Cable) AWG 36, Tin-Coated INSULATION RESISTANCE 10,000 megohms (minimum) for 1000 ft. Copper (helically laid) .275 JACKET FLAWS 1st SHIELD SPARK TEST 3.0 kV (rms) AWG 32, Tin-Coated Copper VOLTAGE WITHSTAND .315 Conductor to Conductor and Shield 1500 volts (rms) 1st JACKET + .005 Shield to Shield 1000 volts (rms) Zerohal -.010 Color - Black ENVIRONMENTAL .331 WATERBLOCK LAYER OPERATING TEMPERATURE 110°C Other testing as required by MIL-DTL-24643/62. 2nd SHIELD PHYSICAL AWG 30, .372 Tin-Coated Copper, INSULATION (DIELECTRIC) Optimized ELONGATION 160% (minimum) 2 TENSILE STRENGTH 700 lbf/in (minimum) JACKET (each) ELONGATION 160% (minimum) WATERBLOCK LAYER .388 2 TENSILE STRENGTH 1300 lbf/in (minimum) JACKET THICKNESS .450 1st JACKET .020 inch (nominal) (minimum) 2nd JACKET .040 inch (minimum), 2nd JACKET .496 .054 inch (nominal) Zerohal (nominal) SHIELD COVERAGE (1st) 90% (minimum) .530 3 (maximum) WATERTIGHTNESS 4 in (maximum) in ASTM D 1141 solution MARKER TAPE RAYCHEM-REDWOOD CITY, CA- (under outer jacket) Yr of Mfr-MIL-DTL-24643-* (* = Serial marker) Outer jacket color will be black designated by a "-0" in JACKET MARK RAYCHEM LSPB2SDOSW-1 accordance with MIL-STD-681 appended to the part number, M24643/62-04 Yr of Mfr XLPOLYO (e.g. 5022W0809-0). Other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the purchase order. WEIGHT 163. lbs/1000 ft. (nominal) Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. Page 1 of 1 Zerohal, Cheminax, Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Raychem Wire & Cable THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. 501 Oakside Avenue REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Redwood City, California 94063-3800 © 2006-2016 Tyco Electronics Corporation. All rights reserved. Phone: 1-800-227-8816 Fax: 1-650-361-6297