TE CONNECTIVITY 7526S1664-9CS3078

SPECIFICATION CONTROL DRAWING 7526S1664 Date 6-6-08 75 OHM, AWG 26, 19 STRANDS OF AWG 38, CHEMINAX DATA BUS CABLE, MIL-STD-1553, OUTER SPACE USE Revision B THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS ELECTRICAL CHARACTERISTICS DIMENSIONS ARE NOMINAL VALUES IN INCHES UNLESS OTHERWISE CHARACTERISTIC IMPEDANCE 75 ± 5 ohms, Method C at 1 MHz DESIGNATED. MUTUAL CAPACITANCE 30.0 pF/ft. (maximum) CONDUCTOR ATTENUATION 1.5 dB/100 ft. (maximum) at 1 MHz AWG 26, 19 Strands of AWG 38, Silver-Coated .0200 High Strength Copper Alloy DIELECTRIC ADDITIONAL REQUIREMENTS .039 Radiation-Crosslinked, ± .003 COMPONENT WIRE PRIOR TO CABLING (Test Procedures per SAE AS22759) Modified ETFE Color - Light Blue/White CROSSLINK PROOF 300 ± 3°C for 1 hour, .500 inch mandrel, .250 lb., 2.5 kV dielectric test INSULATION (DIELECTRIC) ELONGATION 50% (minimum) 2 TENSILE STRENGTH 5000 lbf/in (minimum) INSULATION FLAWS SPARK TEST 3.0 kV (rms) IMPULSE TEST 8.0 kV (peak) INSULATION RESISTANCE 5000 megohms for 1000 ft. (minimum) LOW TEMPERATURE-COLD BEND -65 ± 2°C for 4 hours, .500 inch mandrel, .500 lb., 2.5 kV dielectric test SHIELD SHRINKAGE 200 ± 3°C for 1 hour, .095 AWG 38, .125 inch (maximum) in 12 inches Silver-Coated Copper FINISHED CABLE (Test Procedures per NEMA WC 27500, unless otherwise specified) BLOCKING 200°C for 6 hours CABLE LAY LENGTH .75 inch (minimum), 1.25 inches (maximum) CROSSLINKED VERIFICATION 300 ± 5°C for 6 hours, 3.00 inch mandrel FLAMMABILITY 3 seconds (maximum); 3 inch (maximum); (Method B of Spec 1200) no flaming of facial tissue JACKET JACKET ELONGATION 50% (minimum) .111 2 Radiation-Crosslinked, TENSILE STRENGTH 5000 lbf/in (minimum) Modified ETFE JACKET FLAWS SPARK TEST 1.0 kV (rms) IMPULSE TEST 6.0 kV (peak) JACKET THICKNESS .008 inch (nominal) LOW TEMPERATURE-COLD BEND -55 ± 5°C for 4 hours, 3.00 inch mandrel SHIELD COVERAGE 90% (minimum) VOLTAGE WITHSTAND 1500 volts (rms) (DIELECTRIC) WEIGHT 9.3 lbs/1000 ft. (nominal) OUTER SPACE REQUIREMENTS RADIATION RESISTANCE 500 megarads/3.25 inch mandrel 1.0 kV dielectric test Outer jacket color will be white (designated by a “-9" appended VACUUM STABILITY to the part number, e.g. 7526S1664-9) unless otherwise TOTAL MASS LOSS (TML) 1.00% (maximum) specified. VOLATILE CONDENSABLE 0.10% (maximum) Designate outer jacket color with a dash number in accordance MATERIAL (VCM) with MIL-STD-681. Other codes and suffixes may be added to WEIGHT LOSS: (Test per Spec 55/) 0.45% (maximum) the part number, as necessary, to capture any additional requirements imposed by the purchase order. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. The TE logo, Tyco Electronics, Cheminax and Raychem are trademarks. Raychem Wire & Cable THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS 501 Oakside Avenue Redwood City, California 94063-3800 REFERENCED HEREIN. REFERENCED DOCUMENTS SHALL BE OF THE 1-800-227-8816 Fax: 1-650-361-6297 ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. © 2006-2008 Tyco Electronics Corporation. All rights reserved.