TE CONNECTIVITY 7724C3864-0

SPECIFICATION CONTROL DRAWING 7724C3864 8-19-14 77 OHM, AWG 24, 19 STRANDS OF AWG 36, Date: OPTIMIZED DOUBLE SHIELDS, DATA BUS CABLE, MIL-STD-1553 CHEMINAX E Revision: THIS SPECIFICATION SHEET FORMS A PART OF THE LATEST ISSUE OF RAYCHEM SPECIFICATION 1200. CONSTRUCTION DETAILS ELECTRICAL CHARACTERISTICS DIMENSIONS ARE NOMINAL VALUES IN INCHES, UNLESS OTHERWISE CHARACTERISTIC IMPEDANCE 77 ± 5 ohms, Method C at 1 MHz DESIGNATED. MUTUAL CAPACITANCE 30.0 pF/ft. (maximum) ATTENUATION 1.4 dB/100 ft. (maximum) at 1 MHz CONDUCTORS SURFACE TRANSFER IMPEDANCE 10 milliohms/meter (maximum) AWG 24, at 30 MHz 19 Strands of AWG 36, .0250 Silver-Coated High- Strength Copper Alloy ADDITIONAL REQUIREMENTS DIELECTRICS .048 COMPONENT WIRE PRIOR TO CABLING Radiation-Crosslinked, Modified ETFE (Test procedures per SAE AS22759) Colors - Light Blue/White CONDUCTOR RESISTANCE 26.5 ohms/1000 ft. (nominal) .032 FILLERS CROSSLINKING PROOF TEST 300 ± 3°C for 1 hour, .625 inch mandrel, Radiation-Crosslinked, .375 lb, 2.5 kV dielectric test Modified ETFE INSULATION (DIELECTRIC) ELONGATION 50% (minimum) 2 TENSILE STRENGTH 5000 lbf/in (minimum) INSULATION FLAWS SPARK TEST 3.0 kV (rms) IMPULSE TEST 8.0 kV (peak) INSULATION RESISTANCE 5000 megohms for 1000 ft. (minimum) 1st SHIELD LOW TEMPERA TURE-COLD BEND -65 ± 3°C for 4 hours, .750 inch mandrel, AWG 38, .113 1.00 lb, 2.5 kV dielectric test Tin-Coated Copper, Optimized SHRINKAGE 200 ± 3°C for 1 hour, .125 inch (maximum) in 12 inches 2nd SHIELD AWG 38, FINISHED CABLE .130 Tin-Coated Copper, Optimized CABLE LAY LENGTH .75 inch (minimum), 1.25 inches (maximum) FLAMMABILITY Method B, except 45 seconds (maximum) HEAT SHOCK 225°C JACKET ELONGATION 150% (minimum) 2 TENSILE STRENGTH 1200 lbf/in (minimum) JACKET FLAWS JACKET SPARK TEST 1.0 kV (rms) .190 Zerohal IMPULSE TEST 6.0 kV (peak) JACKET THICKNESS .030 inch (nominal) LOW TEMPERATURE-COLD BEND -30°C/5.00 inch mandrel VOLTAGE WITHSTAND 1500 volts (rms) (DIELECTRIC) VOLTAGE WITHSTAND 1000 volts (rms), 1 minute (Post Environmental) Designate outer jacket color with a dash number in accordance with MIL-STD-681. Unless otherwise specified, outer jacket color will be black (designated by a "-0" appended to the part number, WEIGHT 28.3 lbs/1000 ft. (nominal) e.g. 7724C3864-0). ENGINEERING REFERENCE Other codes and suffixes may be added to the part number, as necessary, to capture any additional requirements imposed by the TEMPERATURE RATING 105°C (maximum) purchase order. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. Page 1 of 1 Zerohal, Cheminax, Raychem, TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Raychem Wire & Cable THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. 501 Oakside Avenue REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. Redwood City, California 94063-3800 © 2007-2014 Tyco Electronics Corporation. All rights reserved. Phone: 1-800-227-8816 Fax: 1-650-361-6297