OP215, OP216 Features:  Hermetically sealed package OP216  Mechanically and spectrally matched to other OPTEK devices  Designed for direct mount to PCBoard  Enhanced temperature range OP215 Description: Each OP215 and OP216 device is an 890 nm gallium aluminum arsenide infrared emitting diode (GaAIAs), mounted in a hermetically sealed “pig tale” package with an enhanced temperature range and a narrow irradiance pattern that provides high on-axis intensity for excellent coupling efficiency. These devices offer significantly higher power output than GaAs at equivalent drive currents and have a wavelength that is matched to silicon’s peak response. Their small package size permits high device density mounting. The OP216A device provide an additional mounting tab connected to the Cathode/Case. these LEDs are mechanically and spectrally matched to the OP300 series, OP516, OP600 series and OP640 series devices. Please refer to Application Bulletins 208 and 210 for additional design information and reliability (degradation) data, and to Application Bulletin 202 for pill-type soldering to PCBoard. Ordering Information Part LED Peak Optical Power mW/ Total Beam Applications: 2 Number Wavelength cm (Min) Angle  Non-contact reflective object sensor OP215A OP216A 890 mm 1.20 24°  Assembly line automation  Machine automation  Machine safety  End of travel sensor 1 Pin # LED 1 Anode Cathode 2 2 RoHS General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue C 04/2018 Page 1 © TT electronics plc Electrical Specifications Absolute Maximum Ratings (T = 25° C unless otherwise noted) A o o Storage Temperature Range -65 C to +150 C o o Operating Temperature Range -65 C to +125 C Reverse Voltage 2.0 V Continuous Forward Current 100 mA Peak Forward Current (2µs pulse with 0.1% duty cycle) 1.0 A (1)(2) Lead Soldering Temperature [1/16 inch (1.6 mm) from case for 5 seconds with soldering iron] 260° C (3) Power Dissipation 150 mW Electrical Characteristics (T = 25° C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode Apertured Radiant Incidence (3) 2 (4) E - - mW/cm I = 50 mA E (APT) F OP216A 1.20 V Forward Voltage - - 1.80 V I = 50 mA F F I Reverse Current - - 100 µA V = 2.0 V R R λ Wavelength at Peak Emission - 890 - nm I = 10 mA P F Spectral Bandwidth between B - 80 - nm I = 10 mA F Half Power Points ∆λ /∆T Spectral Shift with Temperature - +0.18 - nm/°C I = Constant F θ Emission Angle at Half Power Points 24 Degree I = 50 mA HP F - - t Output Rise Time - 500 - ns r I =100 mA, PW=10 µs, and F(PK) D.C.=10.0% t Output Fall Time - 250 - ns f Notes: 1. Refer to Application Bulletin 202 which reviews proper soldering techniques for pill-type devices. 2. No clean or low solids. RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. 3. Derate linearly 1.50 mW/° C above 25° C. 4. For OP216, E is a measurement using a 0.180” (4.57 mm) diameter apertured sensor placed 0.653” (16.59 mm) from the lens tip. E is not E(APT) E(APT) necessarily uniform within the measured area. General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue C 04/2018 Page 2 © TT electronics plc Performance OP215 & OP216 Forward Voltage vs Forward Current vs Optical Power vs I vs Temperature F Temperature 2.0 1.8 Normalized at 50 mA and 20° C 1.8 1.7 -60° C 1.6 -40° C 1.6 -20° C 0° C 1.4 20° C 40° C 1.5 60° C 1.2 80° C 100° C 1.4 120° C 1.0 1.3 0.8 -60° C 0.6 1.2 -40° C -20° C 0° C 0.4 1.1 20° C 40° C 60° C 0.2 1.0 80° C 100° C 120°C 0.0 0.9 0 5 10 15 20 25 30 35 40 45 50 0 5 10 15 20 25 30 35 40 45 50 Forward Current I (mA) F Forward Current (mA) Normalized Intensity vs Beam Angle Distance vs Output Power vs Forward Current 1.1 6 1.0 Normalized at 1" and 50 mA 5 0.9 0.8 Forward Current 10 mA 4 20 mA 0.7 30 mA 40 mA 0.6 50 mA 60 mA 3 70 mA 0.5 80 mA 90 mA 100 mA 0.4 2 0.3 0.2 1 0.1 0 0.0 -45 -35 -25 -15 -5 5 15 25 35 45 0.2 '' 0.4 '' 0.6 '' 0.8 '' 1.0 '' 1.2 '' 1.4 '' 1.6 '' 1.8 '' 2.0 '' Normalized Intensity Distance (inches) Angular Displacement (˚Degrees) General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specification without 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 notice or liability. All information is subject to TT Electronics’ own data and is www.optekinc.com | www.ttelectronics.com considered accurate at time of going to print. Issue C 04/2018 Page 3 © TT electronics plc Normalized Output Power Typical Forward Voltage (V) Angular Displacement (° Degrees) Normalized Intensity Normalized Optical Power