POWER μMP Series GEN II Data Sheet Up to 1800 Watts with New Product Enhancements Total Power: Up to 1800 Watts Peak* Input Voltage: 85 - 264 Vac 120 - 300 Vdc # of Outputs: Up to 12 SPECIAL FEATURES ƒ Full Medical EN60601 approval ƒ PMBus monitor/control of input functions ƒ High efficiency Electrical Specifications ƒ Constant current limit protection Input ƒ High power density. - μMP04: 10.8 W/cu-in Input ra nge 85 - 264 Vac, 120 - 350 Vdc (limited to 300 Vdc in medical applications) - μMP09: 18.5 W/cu-in Frequency 47 - 440 Hz - μMP10: 15.1 W/cu-in Inrush current 40 A peak max. (soft start) - μMP16: 22.9 W/cu-in Efficiency Up to 91.5% @ full case load ƒ Low noise intelligent fan (speed Power factor 0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz) control/fault status), 36% reduction from GEN I Standby power uMP10/16 < 13 W uMP04/09 < 6 W ƒ Downloadable GUI from website Turn-on time AC on 2 sec for μMP16/10 and 1.5 sec for μMP04/09, inhibit/enable 250 ms typical ƒ Optional conformal coating ƒ Industrial temp range (-40 ºC to 70 ºC) EMI: CISPR 22/EN55022 Level “B” (Both Conducted and Radiated) ƒ No preload required Leakage current <200 uA using center-tapped xfmr measurement method. (<400 uA @ 264 VAC input) ƒ Military STD shock/vibration (40G’s) Holdover storage 16.7 ms minimum (independent of input Vac, 0 °C to 50 °C) ƒ Low cost At 1200 W for μMP16 ƒ IEC, terminal block or barrier strip input AC OK Signal goes low indicating loss of AC input. Hold up = Full cycle ride thru (50 Hz); Open collector connection options Harmonic current emission Meets EN61000-3-2 ƒ Low profile 1U size ƒ Superior aesthetics over GEN I Isolation Meets EN60950 and EN60601 Global inhibit/enable TTL, Logic “1” and Logic “0”; fan off when unit is inhibited CERTIFICATIONS Input fuse (internal) μMP16/10: 16 A, 500 Vac, 400 Vdc, μMP04/09: 10 A / 250 V. (both lines fused) ƒ UL UL60950-1 / CSA 22.2 Warranty 2 years No.60950-1/ Output ES60601-1 / CSA 22.2 Factory set point accuracy ± 1% No.60601-1 Margining / V-Program ± 3 - 7% nominal analog (single output module only). Contact factory for simple ƒ TUV EN60950-1 / EN60601-1 V-program modification (i.e. 0-5 V input = 0-100% output voltage). ƒ CB Certificate and Report Overall regulation 0.4% or 30 mV which ever is greater ƒ CE Compliance to LVD and Ripple RMS: 0.1% or 10 mV, whichever is greater RoHS Directives Pk-Pk: 1.0% or 50 mV, whichever is greater. Bandwidth limited to 20 MHz ƒ CQC Approved Dynamic response < ± 5% or 250 mV, with 50% step load ƒ Medical 2x MOPP Recovery time To within 1% in < 300 μsec Reverse voltage protection 100% of rated output current * Max output power for μMP16: 1000 W 90 - 100 VAC; 1200 W 100 - 180 VAC; 1600 W 180 - 200 W; 1800 W 200 - 264 VAC. Operational specs for EMI and Hold-up are valid to 1600 W max. µMP Series Data Sheet Electrical Specifications Output Thermal protection (OTP) All outputs disabled when internal temp exceeds safe operating range Remote sense Up to 0.5 V total drop (not available on triple output module) Single wire parallel Current share to within 5% of total rated current from 20% to 100% rated load DC OK ± 5% of nominal Open collector Minimum load Not required Housekeeping standby 5 Vdc @ 2.0 A max whenever AC input is applied. 1.0 A (2.0 A for μMP04) max convection cooled (when output is inhibited off) Module inhibit Logic - output on with low or open. Different logic options available Output/Output isolation > 1 Megohm, 500 V Environmental Specifications Operating temperature -40 °C to 70 °C ambient. Derate each output 2.5% per degree from 50 °C to 70 °C. Cold start soak -20 °C, allow 10 min warm-up before all outputs are within specification. Reverse air to 40 °C Max due to fan derating. Storage temperature -40 °C to +85 °C Electromagnetic susceptibility Designed to meet EN61000-4:-3,-5,-6,-11 Class 3 Performance Criteria A Humidity Operating; non-condensing 10% to 95% RH Vibration MIL-STD-810E MTBF demonstrated > 350,000 hours at full load, one μMP04 case + two modules, Telcordia SR-332 calculated MTBF Altitude Up to 10 K feet; derate linear to 50% from 10 K - 30 K feet Vout Full load (A) OVP trip max (V) OCP trip typ (Iout%) SCP trip max (Iout%) Overshoot (max mV) Peak Deviation (max mV) 3 V 3 Module 0.9 40 2.00 V 130% 160% 150 ± 250 3.3 40 5.96 V 130% 160% 250 ± 250 3.6 40 6.31 V 130% 160% 250 ± 250 5 V Module 3.2 36 5.76 V 130% 160% 250 ± 250 5 36 9.0 V 130% 160% 250 ± 250 6 30 10.80 V 130% 160% 300 ± 300 12 V Module 6 25 10.80 V 130% 160% 300 ± 300 12 20 15.60 V 130% 160% 600 ± 600 15 16 19.50 V 130% 160% 750 ± 750 24 V Module 12 13 15.60 V 130% 160% 600 ± 600 24 10 31.20 V 130% 160% 120 ± 1200 30 8 39.00 V 130% 160% 1500 ± 1500 48 V Module 28 7 36.40 V 130% 200% 1400 ± 1400 48 5 62.40 V 130% 160% 2400 ± 2400 60 4 78.00 V 130% 200% 3000 ± 3000 µMP Series Data Sheet Case Line-Up Max Output Case Dimensions Connections Max Continous Current 85-180 VAC 180-263 VAC 256.9 x 88.9 x 40.0 IEC, Terminal-Block, μMP04 - 4 Slot 400 W 600 W 9.91 (10.11” x 3.5” x 1.57”) Barrier-Strip 256.9 x 88.9 x 40.0 IEC, Terminal-Block, μMP09 - 4 Slot 550 W 1100 W 9.91 (10.11” x 3.5” x 1.57”) Barrier-Strip 256.9 x 127 x 40.0 IEC, Terminal-Block, μMP10 - 6 Slot 1000 W 1200 W 13.87 (10.11” x 5.0” x 1.57”) Barrier-Strip 256.9 x 127 x 40.0 IEC, Terminal-Block, μMP16 - 6 Slot 1000 W 1800 W 13.87 (10.11” x 5.0” x 1.57”) Barrier-Strip Output Module Line-Up S2* Output Range (Vdc) Max Current (Amps) Max Power (Watts) Module Codes Standard Outputs 0.9 - 3.6 40 144 A, B, C, D - 2, 2.2, 3, 3.3 3.2 - 6.0 36 180 E, F, G, H - 5, 5, 2, 5.5, 6.0 6.0 -15.0 25 240 I, J, K, L, M, N - 8, 10, 11, 12, 14, 15 12.0 - 30.0 13 240 O, P, Q, R, S - 18, 20, 24, 28, 30 33.0 - 60.0 7 240 T, U, V, W, X, Y - 33, 36, 42, 48, 54, 60 3.3 - 30.0 4/4 96/96 Dual Output Module. Each output is rated to 96 W (192 Watts total). Wide range is adjustable. Output Module Line-Up SK* Output Range (Vdc) Max Current (Amps) Max Power (Watts) Module Codes Standard Outputs 18.0 - 30.0 42 1000 O, P, Q, R, S (18, 20, 24, 28, 30 Volts) 33.0 - 60.0 21 1000 T, U, V, W, X, Y (33, 36, 42, 48, 54, 60 Volts) Internal Part Number Reference Table Part # Where X = Description Module Code 73-951-0001X-G2 T, C, S μMP10 Cases μMP10 73-956-0001X-G2 T, C, S μMP16 Cases μMP16 73-963-XXXX 0012, 0024, 0048, 04XX uMP 1000W Module SKL - SKZ 73-963-00XX-G2 0012, 0024, 0048, 04XX uMP 1000W Module SKL - SKZ Ordering Information µ MPXY - SKW - S2E - S2Q - ILL - 00 - A - ### Case Size Module/Voltage Case Option Codes Software Code Hardware Code 1-Phase Input where X = Module Codes: First digit Factory assigned 4 = 1.57” x 3.5” x 10.0”; 400W - 600W 4 Slots* S2 = 200 W Single O/P (1 Slot) 0-9 = Parallel Code for modified standards 04 = 1.57” x 3.5” x 10.0”; 400W - 600W 4 Slots SK = 1000 W Single O/P (3 Slot) I = 96 W Dual O/P ISO GND (1 Slot) Second Digit 09 = 1.57 x 3.5 x 10.0, 550W-1100W 4 Slots 1 = 1.57 x 5.0” x 10.0”, 1000W-1200W, 6 Slots* 0 = No Options 10 = 1.57 x 5.0” x 10.0”, 1000W-1200W, 6 Slots Voltage Codes: See voltage code 1 = Reverse Air 16 = 1.57” x 5.0” x 10.0”, 1200W-1800W**, 6 Slots table 2 = Not Used 3 = Global Enable * Not Recommended for new designs 5 = Opt 1 + Opt 3 ** See Input Derating table below for uMP16 Input Type where Y = T = Terminal Block C = IEC Connector C14 S = Barrier Strip μMP16 INPUT POWER DERATING Paramater 85 - 99 Vac 100 - 140 Vac 180 - 199 Vac 200 - 264 Vac Designed For 1000 W 1200 W 1600 W 1800 W QAV Evaluation 1000 W 1200 W 1600 W 1800 W Safety Label and Evaluation 1000 W 1000 W 1600 W 1600 W µMP Series Data Sheet Parallel Codes Code Slots in Parallel Code Slots in Parallel Code Slots in Parallel Code Slots in Parallel 1 1&2 6 1&2&3 A 1&2; 3&4 0 no module in parallel 2 2&3 7 1,2,3&4 B 1,2&3; 4&5 H 3,4&5 3 3&4 8 1,2,3,4&5 C 1,2,3&4; 5&6 J 3,4,5&6 4 4&5 9 1,2,3,4,5&6 D 1&2; 3&4; 5&6 K 4,5&6 5 5&6 E 1,2&3; 4,5&6 Notes: Parallel between SK* (1000 W Modules) and S2* (240 W Modules) will use the codes as follows Code 3 to parallel 2 SK* modules Code 3 to parallel 1 SK* module and 1 S2* module Code H to parallel 1 SK* module and 2 S2* modules Voltage Codes Derating Curves - μMP10 Standard Output Ratings Standard Fan (12 V/24 V/48 V) Single Single Output 85 VAC 100 VAC 110 VAC 200 VAC 264 VAC Module Output Output One Dual Output One Slot Standard Fan (12 V/24 V/48 V) Three Slots Voltage Code Slot 240 96 Watts 1000 Watts 1200 Watts Max 85 VAC 100 VAC 110 VAC 200 VAC 264 VAC Max 1100 1200 Module S2 SK I Identification 1000 1100 900 Output Current Output Output 1000 Code Volts Current Current 800 V1 V1 V1 V2 900 700 800 A 2.0 40.0 - NA 600 B 2.2 40.0 - NA 700 500 C 3.0 40.0 - NA 600 400 D 3.3 40.0 - 4.0 4.0 500 0 10 20 30 40 50 60 70 E 5.0 36.0 - 4.0 4.0 Temperature 400 0 10 20 30 40 50 60 70 F 5.2 34.0 - 4.0 4.0 Temperature G 5.5 32.0 - 4.0 4.0 Reverse FAN (12 V/24 V/48V) H 6.0 30.0 84.0 4.0 4.0 85 VAC 100 VAC 110 VAC 200 VAC 264 VAC Reverse FAN (12 V/24 V/48V) I 8.0 25.0 84.0 4.0 4.0 1200 85 VAC 100 VAC 110 VAC 200 VAC 264 VAC J 10.0 24.0 84.0 4.0 4.0 1100 1200 K 11.0 22.0 84.0 4.0 4.0 1000 1100 L 12.0 20.0 84.0 4.0 4.0 900 1000 M 14.0 17.0 71.4 4.0 4.0 800 900 N 15.0 16.0 66.7 4.0 4.0 700 800 O 18.0 13.0 42.0 4.0 4.0 600 700 P 20.0 12.0 42.0 4.0 4.0 500 600 Q 24.0 10.0 42.0 4.0 4.0 400 500 0 10 20 30 40 50 60 7 0 R 28.0 8.6 35.7 3.4 3.4 Temperature 400 S 30.0 8.0 33.3 3.2 3.2 0 10 20 30 40 50 60 7 0 Temperature T 33.0 7 21.0 NA U 36.0 6.7 21.0 NA V 42.0 5.7 21.0 NA W 48.0 5.0 21.0 NA X 54.0 4.4 18.5 NA Y 60.0 4.0 16.7 NA Output Power Output Power Output Power Output Power µMP Series Data Sheet μMP04/09 (AC input on opposite side) μMP10/16 (AC input on opposite side) S S S S S S S S S S J2 J2 L L L L L L L L L L O O O O O O O O O O T T T T T T T T T T J1 4 21 J1 3 6 5 4 3 1 2 Input Input 85 - 264 Vac 200 - 264 Vac 85 - 264 Vac 200 - 264 Vac µMP04 = 4 available slots 400 W max. 600 W max. µMP10 = 6 available slots 1000 W max. 1200 W max. µMP09 = 4 available slots 550 W max. 1100 W max. µMP16 = 6 available slots 1200 W max. 1800 W max. Pin Connectors Figure 1. AC Input J2 2 I C Bus Output Connector AC Input Pin Function Pin Function IEC Connector Mates with 1 5 Vcc bus 1 AC neutral Landwin 2050S1000 Housing 2 Serial data signal (SDA) 2 AC line (hot) 2053T011V Pin 3 Secondary return (COM) 3 Chassis (earth) ground or Terminal Block 4 Serial clock signal (SCL) JST PHDR-10VS Housing PEN L 5 Address bit 2 (A2) JST SPHD-002T-P0.5 (28-24) J1 PFC Input Connector 6 No connection JST SPHD-001T-P0.5 (26-22) (control & signals) 7 Address bit 1 (A1) Connector Kit Part No.: Pin Function 8 No connection 70-841-023 1 Input AC OK - “emitter” 9 Address bit 0 (A0) 2 Input AC OK - “collector” 10 No connection 3 Global DC OK - “emitter” 4 Global DC OK - “collector” 5 Spare 6 Global inhibit/optional enable logic “1” 7 Global inhibit/optional enable logic “0” 1 9 8 Global inhibit/optional enable return 2 10 9 +5 VSB housekeeping Figure 2. Connector J1 & J2 10 +5 VSB housekeeping return S2 Module 240 W DC Output Control & Signals (Single output) Pin Function 1 No connection 2 No connection 3 Current share 4 Module inhibit return 5 Module ISO inhibit V ADJ 5.3±0.5 1.0±0.25 6 SCOM 7 -RMT sense 29.8±0.2 37.5±0.3 8 Margin 36.5±0.3 32.5±0.3 V+ 36.5±0.3 9 Remote margin / V prog. V- 10 +RMT sense CAPS HEIGHT 4.5±0.3 12.5 MAX 3.0 MAX 0.8 - 1.5 1.6±0.16 1 9 2 10 130.0±1.5 µMP Series Data Sheet SK Module 1000 W 12/24 Volt Output: 48 V Output: DC Output Control & Signals (Single output) Pin Function 1 No connection 122.00 0.5 2 No connection 3 Current share 4 Module inhibit return 5 Module ISO inhibit 6 SCOM 7 -RMT sense 8 Margin 9 Remote margin / V prog. 10 +RMT sense Dual Module DC Output Control & Signals (Dual output) Pin Function 1 -RMT sense V2 2 +RMT sense V2 3 No connection 4 Module inhibit rtn 5 Module ISO inhibit 6 SCOM 7 -RMT sense V1 8 No connection 9 No connection 10 +RMT sense V1 +0.30 52.40 -0.30 34.70±0.50 µMP Series Data Sheet μMP Series μMP04/09 (400/600; 550/1100 Watts Max) Case Size: μMP04/09: 10.11” x 3.5” x 1.57” (256.9 mm x 88.9 mm x 40.0 mm) Weight: μMP04/09 Case: 1.96 lbs • Single O/P: 0.22 lb. • Dual O/P: 0.16 lb. • Blank: 0.06 lb. Notes: 1. Input: IEC 60320 C13 (for IEC connector) Barrier Type DECA Switchlab MT300-50003 (for terminal block connector); Max Torque: 4.0 lb-in (0.4 - 0.5 Nm); Wire: 12 - 16 AWG; Wire Strip Length: 0.354” (9.0 mm) 2. Control Connectors (J1 and J2): 10-position housing, brass, matte tin-plated contacts. Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins or housing PHDR-IOVS (JST) and SPHD- 002T-PO.5 (JST) pins. 3. Output Module Connectors: All single O/P modules are M4 x 10 mm screws; tighten between 6.94 to 8.68 lb-in (8.0 to 10.0 kg-cm). Dual O/P module is PUSH IN conductor connector; Wire Strip Length: 0.315” (8.0 mm); Control signal connector: Refer to Item 2. 4. Chassis Material: Steel with chemical film coating (conductive). 5. Customer Mounting: Screw M4-type mounting holes; Max. Penetration is 0.138” (3.5 mm); Max. Torque: 8.85 lb-in (1.0 N-m) 6. All dimensions are in millimeters and inches, and are typical. µMP Series Data Sheet μMP10 (1000/1200 Watts Max) μMP16 (1200/1800 Watts Max) Case Size: μMP10/16: 10.11” x 5” x 1.57” (256.9 mm x 127 mm x 40.0 mm) Weight: μMP10/16 Case: 2.78 lbs • Single O/P: 0.22 lb. • Dual O/P: 0.16 lb. • Blank: 0.06 lb. Notes: 1. Input: IEC 60320 C13 (for IEC connector) Barrier Type DECA Switchlab MT300-50003 (for terminal block connector); Max Torque: 4.0 lb-in (0.4 - 0.5 Nm); Wire: 12 - 16 AWG; Wire Strip Length: 0.354” (9.0 mm) 2. Control Connectors (J1 and J2): 10-position housing, brass, matte tin-plated contacts.Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins or housing PHDR-IOVS (JST) and SPHD- 002T-PO.5 (JST) pins. 3. Output Module Connectors: All single O/P modules are M4 x 10 mm screws; tighten between 6.94 to 8.68 lb-in (8.0 to 10.0 kg-cm). Dual O/P module is PUSH IN conductor connector; Wire Strip Length: 0.315” (8.0 mm); Control signal connector: Refer to Item 2. 4. Chassis Material: Steel with chemical film coating (conductive). 5. Customer Mounting: Screw M4-type mounting holes; Max. Penetration is 0.138” (3.5 mm); Max. Torque: 8.85 lb-in (1.0 N-m) 6. All dimensions are in millimeters and inches, and are typical. WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. Specifications subject to change without notice. © 2017 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. μMP Series-DS 28Jun2017