POWER DS1100PED Data Sheet 1100 Watts Distributed Power System Front-end Bulk Power Total Output Power: 1100 W continuous Wide Input Voltage: 90 - 264 Vac SPECIAL FEATURES ƒ 1100 W output power ƒ High-power and short form factor ƒ 1U power supply 3 ƒ High-density design: 24 W/in Electrical Specifications ƒ Active Power Factor Correction Input ƒ EN61000-3-2 Harmonic compliance Input range 90 - 264 Vac ƒ Inrush current control Frequency 47 Hz to 63 Hz ƒ 80plus Platinum efficiency Efficiency 94.0% peak ƒ N+1 or N+N redundant Max input current 14.5 Arms ƒ Hot-pluggable ƒ Active current sharing Inrush current 55 Apk ƒ Full digital control Conducted EMI Class A ƒ PMBus compliant Radiated EMI Class A ƒ Accurate input power reporting Power factor > 0.9 beginning at 20% load ƒ Compatible with Artesyn’s ITHD 10% Universal PMBus GUI Leakage current 1.4 mA ƒ Reverse airflow option Hold-up time 10 ms at full load ƒ Two-year warranty Output Main DC Output Standby DC Output COMPLIANCE MIN NOM MAX MIN NOM MAX ƒ EMI Conducted/Radiated Class A Limits + 6 dB margin Nominal setting -0.20% 12 0.20% -1% 12 1% ƒ EN61000-4-11 Total output regulation range 11.4 V 12.6 V 11.4 V 12.6 V Dynamic load regulation range 11.4 V 12.6 V 11.4 V 12.6 V SAFETY Output ripple 120 mVp-p 120 mVp-p ƒ UL/cUL 60950 (UL Recognized) Adjustment range TBD 0.1 A 3.0 A ƒ DEMKO+ CB Report EN60950 1 Output current 2 A 91.76 A ƒ EN60950 Current sharing Within 3.7 A from 20% to 100% load N/A ƒ CE Mark Capacitive loading 2000 µF 40,000 µF 47 uF 680 µF ƒ China CCC Start-up from AC to output 2200 ms 1700 ms ƒ BSMI Output rise time 5 ms 50 ms 2 ms 60 ms 1 Minimum current for transient load response testing only. Unit is designed to operate and be within output regulation range at zero load. DS1100PED Data Sheet Electrical Specifications Protections Main Output MIN NOM MAX 2 Overcurrent protection 120% 150% 1 Overvoltage protection 13.5 V 15.0 V Undervoltage protection 10.5 V 11.0 V Overtemperature protection Yes Fan fault protection Yes Standby Output 3 Overcurrent protection 120% 150% 3 Overvoltage protection 13.5 V 15.0 V Undervoltage protection 10.0 V 11.0 V 1 Latch mode 2 Autorecovery if the overcurrent is less than 120% and last only for <500 ms 3 Standby protection is auto-recovery Power Derating DS1100PED-3 DS1100PED-3-001 1200 1100 1000 900 800 700 600 500 10 20 30 40 50 60 Ambient Temperature (degC) Ordering Information Model Number Nominal Main Output Standby Output Airflow Direction DS1100PED-3 12 V 12 V @ 3 A Std (forward) 1 DS1100PED-3-001 12 V 12 V @ 3 A Reverse 1 Derating may apply Output Power at 90Vac DS1100PED Data Sheet Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK PSKILL_L First break/last mate active LOW signal which enables/disables the main output. This signal will have to be pulled to ground at the system side with a 220 ohm resistor. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK Output Signals ACOK Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX V Input logic level LOW 0.6 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 10 kohm resistor. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK DS1100PED Data Sheet Control and Status Signals Output Signals PS_PRESENT_L Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is shorted to the standby return in the power supply. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. PS_INTERRUPT_L Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP, OCP, OTP, and fan fault. This signal can be cleared by a CLEAR_FAULT command. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin at low state 4 mA SINK BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX I Voltage Vshare at 100% load, stand-alone unit 7.75 8.25 SHARE Voltage at 50% load, stand-alone unit 3.85 4.15 Voltage at 0% load, stand-alone unit 0 0.3 I Current that may be sourced by this pin 160 mA SOURCE SCL, SDA 2 Clock and data signals defined as per I C requirements. It is recommended that these pins be pulled-up to a 2.2 kohm resistor to 3.3 V and a 100 pF decoupling capacitor at the system side. VL Input logic level LOW 0.8 V VH Input logic level HIGH 2.0 V 5.0 V Note: All signal noise levels are below 300 mVpk-pk from 0 - 100 MHz. 2 2 2 I C Addressing Table: Not applicable. This power supply has a fixed I C address. In order to support multiple addresses, the system will have to utilize a switcher or an I C expander. DS1100PED Data Sheet Electrical Specifications LED Indicators A single bi-color LED is used to indicate the power supply status. Status LED No AC input to PSU Off when stand-alone, blinking AMBER when in parallel Main output ON Solid GREEN Standby mode or Power supply failure (OCP, OVP, OTP, FAN FAULT) Blinking AMBER Firmware Reporting and Monitoring Accuracy Range Output loading 5 to 20% 20 to 50% 50 to 100% Input voltage ± 5% Input current ± 0.55 A fixed error ± 4% Input power ± 1.25 W at < 125 W input ± 1.25% Output voltage ± 2% Output current 0.3 A fixed error ± 2% Temperature ± 5 °C on the operating range E ± 15% from 10% to 20% load ± 5% IN Fan speed Actual RPM ± 250 RPM PMBus YES Remote ON/OFF YES Over-current limit trimming YES DS1100PED Data Sheet Electrical Specifications Timing Specifications Description Min Max Unit T Delay from AC being applied to standby output being within regulation 20 1700 ms sb_On T Delay from standby output to ACOK assertion See note below 20 ms sb_ACOK T Delay from standby output to main output voltage being within regulation 300 ms sb_Vout T Delay from AC being applied to main output being within regulation 2000 ms AC_On_Delay T Delay from output voltages within regulation limits to PWOK asserted 100 1000 ms PWOK_On T Delay from loss of AC to assertion of ACOK 6 ms ACOK_Delay T Delay from loss of AC to deassertion of PWOK 10 ms PWR_GOOD_Hold-up T Delay from loss of AC to main output being within regulation 11 ms Vout_Hold-up T Delay from loss of AC to standby output being within regulation 150 ms sb_Hold-up T Delay from deassertion of PWOK to output falling out of regulation 1 ms PWR_GOOD_Off T Delay from PSON assertion to output being within regulation 350 ms PSON_On_Delay T Duration of PWOK being in deasserted state during an ON/OFF cycle of PSU N/A N/A PWOK_Low Note: T : tested at 1A load on standby output Vout_hold-up T : ACOK can assert earlier than the standby output sb_ACOK Timing Diagram AC Input T T sb_Hold-up sb_On T ACOK_Delay Vout_stby T sb_Vout T sb_ACOK ACOK T T AC_On_Delay Vout_Hold-up Vout_main T PWOK_On T PWOK_Off PWOK T PWOK_Hold-up T PSON_On_Delay PSON DS1100PED Data Sheet Mechanical Outline STD (FORWARD) AIRFLOW A 9±0.5 196,5±0.5 1,5 40,2 MODEL LABEL IEC C16 AC inlet A 15±0.3 190,9±0.5 A 38,5±0.5 86,3±0.5 9,5 17,8 4±0.2 9,3±0.3 20 61,9 0,6 DS1100PED Data Sheet Output Connector Pin Configuration Connector Definitions S1 PS PRESENT S13 PS_ON Output Connector Part Number Card-edge S2 Reserved S14 PS_KILL Mating Connector Part Number FCI 10107844-002LF or equivalent S3 Reserved S15 Reserved S4 Pwr_Good S16 RTN Power Supply Output Card Edge (Bottom Side) S5 ACOK (AC Input Present) S17 SDA S24 S13 . . S6 RTN S18 RTN . P29-P36 P21-28 S7 I-SHARE S19 SCL P19/20 S8 RESERVE S20 RTN S9 PS INTERRUPT_L S21 REMOTE SENSE- S10 RTN S22 RTN Power Supply Output Card Edge (Top Side) S11 Reserved S23 REMOTE SENSE+ S12 Reserved S24 RESERVE P1-P8 Vo P19-P20 VSB P9-P18 P1-P8  . . P9-P18 RTN P21-P28 RTN S1 S12 P29-P36 Vo Environmental Specifications Operating temperature 0 to 50 °C, refer to power derating curve for operation up to 65 °C Operating altitude up to 10,000 feet, CCC claims exemption for 5000 m Operating relative humidity 20% to 80% non-condensing, non-tropical climate Non-operating temperature -40 to +70 °C Non-operating relative humidity 10% to 95% non-condensing Non-operating altitude up to 50,000 feet Vibration and shock Standard operating/non-operating shock/vibration ROHS compliance YES MTBF 200,000 hours per Telcordia Issue 2, Method 1, Case 3 at 25 °C ambient at full load Operating life Minimum of 5 years Reliability All electronic component derating analysis is done at maximum ambient, 80% of maximum rated load, nominal input line voltage. WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Waterfront Business Park 14/F, Lu Plaza Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street USA West Midlands, DY5 1LX Kwun Tong, Kowloon +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. Specifications are subject to change without notice. © 2017 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. DS1100PED 11Dec2017