POWER DS1100SDC Data Sheet 1100 Watts Distributed Power System Front-end Bulk Power Total Output Power: 1100 W continuous Wide Input Voltage: -36 to -72 Vdc SPECIAL FEATURES ƒ 1100 W output power ƒ High power and short form factor ƒ 1U power supply 3 ƒ High-density design: 24 W/in ƒ Inrush current control ƒ N+1 or N+N redundant Electrical Specifications ƒ Active current sharing ƒ Full digital control Input ƒ PMBus compliant Input range -36 to -72 Vdc ƒ Compatible with Artesyn’s Efficiency 90.0% peak Universal PMBus GUI Max input current 37 Arms ƒ Reverse airflow available Inrush current 55 Apk ƒ Two-year warranty Conducted EMI Class A Radiated EMI Class A COMPLIANCE Hold-up time 1 ms at full load ƒ EMI Conducted/Radiated Class A Limits Output Main DC Output Standby DC Output SAFETY MIN NOM MAX MIN NOM MAX ƒ UL/cUL 60950 (UL Recognized) Nominal setting -0.20% 12 0.20% -1% 12 1% ƒ DEMKO+ CB Report EN60950 Total output regulation range 11.4 V 12.6 V 11.4 V 12.6 V ƒ EN60950 Dynamic load regulation 11.4 V 12.6 V 11.4 V 12.6 V ƒ CE Mark range ƒ China CCC Output ripple 120 mVp-p 120 mVp-p 1 Output current 2 A 91.76 A 0.1A 3.0A Current sharing Within ±5% of full load rating N/A Capacitive loading 2000 µF 40,000 µF 47 µF 680 µF Start-up from input to output 2200 ms 1700 ms Output rise time 5 ms 50 ms 2 ms 60 ms 1 Minimum current for transient load response testing only. Unit is designed to operate and be within output regulation range at zero load. DS1100SDC Data Sheet Electrical Specifications Protections Main Output MIN NOM MAX 2 Overcurrent protection 120% 150% 1 Overvoltage protection 13.5 V 15.0 V Undervoltage protection 10.5 V 11.0 V Overtemperature protection Yes Fan fault protection Yes Standby Output 3 Overcurrent protection 120% 150% 3 Overvoltage protection 13.5 V 15.0 V Undervoltage protection 10.0 V 11.0 V LED Indicators A single bi-color LED is used to indicate the power supply status. Status LED No DC input to PSU Off Main output ON Solid GREEN Standby mode or Power supply failure (OCP, OVP, OTP, FAN FAULT:) Blinking AMBER Firmware Reporting And Monitoring Accuracy Range 50 to 100% Output loading 5 to 20% 20 to 50% Input voltage 2% Input current ±0.55 A fixed error ±4% Input power ±1.25 W at < 125 W input ±1.25% Output voltage ±2% Output current 0.3 A fixed error ±2% Temperature ±5 °C on the operating range E ±15% from 10% to 20% load ±5% IN Fan speed Actual RPM ±250 RPM PMBus YES Remote ON/OFF YES 1 Latch mode 2 Autorecovery if the overcurrent is less than 120% and last only for <500 ms 3 Standby protection is auto-recovery DS1100SDC Data Sheet Electrical Specifications Timing Specifications Description Min Max Unit T Delay from DC input being applied to standby output being within regulation 20 1700 ms sb_On T Delay from standby output to INPUT_OK assertion See note below 20 ms sb_INPUT_OK T Delay from standby output to main output voltage being within regulation 300 ms sb_Vout T Delay from DC input being applied to main output being within regulation 2200 ms INPUT_On_Delay T Delay from output voltages within regulation limits to PWOK asserted 100 1000 ms PWR_GOOD_On T INPUT_OK_Delay Delay from loss of DC input to assertion of INPUT_OK 6 ms T Delay from loss of DC input to deassertion of PWOK 0.2 ms PWR_GOOD_Hold-up T Delay from loss of DC input to main output being within regulation 1 ms Vout_Hold-up T Delay from loss of DC input to standby output being within regulation 150 ms sb_Hold-up T Delay from deassertion of PWOK to output falling out of regulation 1 ms PWR_GOOD_Off T Delay from PSON assertion to output being within regulation 350 ms PSON_On_Delay T Duration of PWOK being in deasserted state during an ON/OFF cycle of PSU N/A N/A PWOK_Low Note: T : tested at 1A load on standby output sb_hold-up T : INPUT_OK can assert earlier than the standby output sb_INPUT_OK Environmental Specifications Operating temperature DS1100SDC-3: 1100W from 0 to 50 °C DS1100SDC-3-001: 1100W from 0 to 40°C Operating altitude up to 10,000 feet with derating Operating relative humidity 20% to 80% non-condensing Non-operating temperature -40 to +70 °C Non-operating relative humidity 10% to 95% non-condensing Non-operating altitude up to 50,000 feet Vibration and shock Standard operating/non-operating shock/vibration ROHS compliance YES MTBF 200,000 hours per Telcordia Issue 2, Method 1, Case 3 at 25 °C ambient at full load Operating life Minimum of 5 years Reliability All electronic component derating analysis is done at maximum ambient, 80% of maximum rated load, nominal input line voltage. DS1100SDC Data Sheet Timing Diagram DC Input T T sb_Hold-up sb_On T Input_Delay Vout_stby T sb_Vout T sb_INPUT_OK INPUT_OK T Input_On_Delay T PWOK_Off Vout_main T T PWOK_On PWOK_Off PWOK T PWOK_Hold-up T PSON_On_Delay PSON DS1100SDC Data Sheet Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I SOURCE Current that may be sourced by this pin 2 mA I Current that may be sunk by this pin at low state 0.5 mA SINK PSKILL_L First break/last mate active LOW signal which enables/disables the main output. This signal will have to be pulled to ground at the system side with a 220 ohm resistor. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK Output Signals INPUT_OK Signal used to indicate the presence of DC input to the power supply. A logic level HIGH will indicate that the DC input to the power supply is within the operating range while a logic level LOW will indicate that DC input has been lost. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recom- mended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX V Input logic level LOW 0.6 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of DC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recom- mended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 10 kohm resistor. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK DS1100SDC Data Sheet Control and Status Signals Output Signals PS_PRESENT_L Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is shorted to the standby return in the power supply. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. PS_INTERRUPT_L Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP, OCP, OTP, and fan fault. This signal can be cleared by a CLEAR_FAULT command. Recommended pull-up resis- tor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin at low state 4 mA SINK BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX I Voltage Input logic level LOW 7.75 8.25 SHARE Voltage at 50% load, stand-alone unit 3.85 4.15 Voltage at 0% load, stand-alone unit 0 0.3 I Current that may be sourced by this pin 160 mA SOURCE SCL, SDA 2 Clock and data signals defined as per I C requirements. It is recommended that these pins be pulled-up to a 2.2 kohm resistor to 3.3 V and a 100 pF decoupling capacitor at the system side. VL Input logic level LOW 0.8 V VH Input logic level HIGH 2.0 V 5.0 V Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. 2 2 I C Addressing Table: Not applicable. This power supply has a fixed I C address. In order to support multiple addresses, the system will have to 2 utilize a switcher or an I C expander. Ordering Information Model Number Nominal Main Output Standby Output Airflow Direction DS1100SDC-3 12 V 12 V @ 3A Std (forward) 1 DS1100SDC-3-001 12 V 12 V @ 3A Reverse 1 Derating may apply DS1100SDC Data Sheet Mechanical Drawing AIRFLOW DIRECTION Standard (Forward) 196,50 40,2 9,0 A 5,5 15,00 185,47 WATTAGE LABEL 0,1 SECTION A-A Connector Definitions Output Connector Part Number Card-edge Mating Connector Part Number FCI 10107844-002LF or equivalent Power Supply Output Card Edge (Bottom Side) Power Supply Output Card Edge (Top Side) S24 S13 . . . P29-P36 P21-28 P19/20 P1-P8  P9-P18 . . S1 S12 Input Connector (System Side) Molex 394210002 PSU Side Connector Part Number Molex 394250002 Vin+ Vin- 86,30 38,50 9,50 17,80 4,00 9,31 20,0 0,6 6,5 61,9 DS1100SDC Data Sheet Output Connector Pin Configuration S1 PS PRESENT S13 PS_ON S2 Reserved S14 PS_KILL S3 Reserved S15 Reserved S4 Pwr_Good S16 RTN S5 INPUT_OK (Input Present) S17 SDA S6 RTN S18 RTN S7 I-SHARE S19 SCL S8 RESERVE S20 RTN S9 PS INTERRUPT_L S21 REMOTE SENSE- S10 RTN S22 RTN S11 Reserved S23 REMOTE SENSE+ S12 Reserved S24 RESERVE P1-P8 Vo P19-P20 VSB P9-P18 RTN P21-P28 RTN P29-P36 Vo Derating Curves Temperature vs Power Derating Curve 1200 1000 800 600 DS1100SDC-3 400 DS1100SDC-3-001 200 0 10 20 30 40 50 60 70 Ambient Temperature °C WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street Kwun Tong, Kowloon USA West Midlands, DY5 1LX +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. DS1100SDC 21Jun2016 Output Power (W)