DS1200-3-002 - ARTESYN - Electronics Finder

Description

1200 W, Single Output, 12 V@98 A Datacom/Industrial/OEM/Commercial Hot-Swap AC-DC Power Supply

Part Number

DS1200-3-002

Price

Request Quote

Manufacturer

ARTESYN

Lead Time

Request Quote

Category

Circuit Protection » AC-DC Power Supply

Specifications

Manufacturer

Artesyn

Manufacturers Part #

DS1200-3-002

Brand

Artesyn Embedded Technologies

Series

DS1200

Factory Pack Quantity

Application

Front End

Cooling Method

Air-Cooled

Dimensions

11.00 x 3.20 x 1.57"

Efficiency

91%

Environmental Conditions

General Purpose

Industry

Datacom, Industrial, OEM/Commercial

Input Type

Mechanical Style

Hot-Swap

Number of Outputs

Operating Temperature

-10 to +70°C, derate linearly to 50% power from 50-70°C

Output Amps 1

98 A

Output Voltage V1 Nominal

12 V

Package Type

Hot-Swap

Power

1200 W

Subcategory

AC-DC Power Supply

Datasheet

ds1200_ds_1219707774.pdf

1562 KiB

Download

Extracted Text

POWER DS1200 Data Sheet 1200 Watts Distributed Power System Distributed Power Bulk Front-End Total Output Power: 1200 Watts +3.3 Vdc Stand-by Output Wide Range Input Voltage: 90 - 264 Vac Special FeatureS Active power factor correction EN61000-3-2 harmonic compliance Active AC inrush control 1U X 2U form factor 21.71 W/in3 +12 Vdc Output Electrical Specifications +3.3 Vdc or +5.0 Vdc stand-by Input No minimum load required Input range: Hot plug operation 180 - 264 (1200 W) 90 - 264 (1000 W) N + 1 redundant Internal OR’ing fets Frequency: 47-63 Hz, single phase AC Active current sharing Inrush current: 40 Apk maximum inrush current (10 - 100% load) Efficiency: > 91% typical at high line 50% load Built-in cooling fan Conducted EMI: FCC Subpart J EN55022 Class B (40 mm x 28 mm) 2 Radiated EMI: FCC Subpart J EN55022 Class B I C communication interface bus PMBus compliant Power factor: 0.99 typical EEPROM for FRU data Leakage current: 1.40 mA @ 240 VAC Red/green bi-color LED status Hold up time: 12 ms minimum Internal fan speed control Output Fan Fail Tach Output Signal Main DC voltage: +12 V @ 100 A (high line) Full digital control +12 V @ 81.6 A (low line) Two year warranty Stand-By: +3.3 Vsb @ 6 A (5 V @ 4 A available) 2 Adjustment range: ±5% on +12V only using I C SaFety Regulation: +12 Vdc; +5%/-5% UL/cUL 60950 (UL Recognized) +3.3 Vsb; +5%/-5% NEMKO+ CB Report EN60950 Over current: +12 Vdc; latches off if overcurrent lasts over 1 second, EN60950 otherwise it is auto recovery (See Table 1 next page) +3.3 Vsb, 9 A CE Mark max (hiccup mode) China CCC Over voltage: +12 Vdc; 13.2 - 14.4 Vdc +3.3 Vsb; 3.76 - 4.30 Vdc Under voltage: +12 Vdc; 9 - 10.8 V (latch off) Turn-on delay: 2 second max, 5 - 50 mS, monotonic rise Main output rise time: 5 - 50 mS, monotonic rise DS1200 Series Data Sheet Logic Control PS_SEATED (A4): TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if the PSU is removed PWR GOOD (C3): Active TTL high when output is within regulation limits. AC OK (B1): A low logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 5mS early warn- ing signal before 12.0 V DC output loss of regulation. PS_INHIBIT/PS_KILL (B4): When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin will be pull low by the system and turn the power supply on only after all other power supply pins have seated. PS ON (A1): The output will be enabled when this signal is pulled low, below 0.8 V outputs disabled when pin is driven high or left open. Environmental Specifications Operating temperature: -10° to 50 °C Storage temperature: -40 °C to +85 °C Altitude, operating: 10,000 ft Electromagnetic susceptibility/Input transients: -EN61000-3-2, -3-3 -EN61000-4-2, 4.3, 4-4, -4-5, 4-11 -EN55024:1998 RoHS & lead-free compliant: No tantalum caps. Humidity: 20 to 90% RH, non-condensing Shock and vibration specificatons: Complies with standard operating/non-operating random shock and vibration MTBF (Demonstrated): 500K Hrs at full load, 25 °C DS1200 Series Data Sheet Ordering Information Nominal Output Output Set Point Total Minimum Maximum Model Number Ripple Over Current Stand-by Air Flow Voltage Tolerance Regulation Current Current P/P Set Point * DS1200-3 12.0 Vdc ±0.2% ±5% 0 A 100 A 120 mV 118 A - 147.6 A 3.3 V @ 6 A STD DS1200-3-002 12.0 Vdc ±0.2% ±5% 0 A 100 A 120 mV 118 A - 147.6 A* 5.0 V @ 4 A STD ** DS1200-3-003 12.0 Vdc ±0.2% ±5% 0 A 100 A 120 mV 118 A - 147.6 A* 3.3 V @ 6 A REV ** DS1200-3-004 12.0 Vdc ±0.2% ±5% 0 A 100 A 120 mV 118 A - 147.6 A* 5.0 V @ 4 A REV * Over current latches off if overcurrent lasts over 1 seconds, otherwise it is auto recovery. Derating may apply. DS1200 Series Data Sheet Mechanical Drawing Condition LED Status Stand-by - ON; Main output - OFF; AC PRESENT Blinking green Stand-by - ON; Main output - ON; Solid green Main output OCP, UVP, OVP Blinking Amber FAN_FAULT; OTP; Stand-by OCP/UVP Amber DS1200 Series Data Sheet DC Output Connector Pinout Assignment Male connector as viewed from the rear of the supply: D1 D2 D3 D4 D5 D6 C1 C2 C3 C4 C5 C6 PB1 PB2 PB3 PB4 PB5 PB6 B1 B2 B3 B4 B5 B6 A1 A2 A3 A4 A5 A6 P1 - Power Supply Side Mating Connector (System Side) 1 FCI Power Blade 51721 series 1 FCI Power Blade 51721-10002406AA 51741-10002406CC Strait Pins 2 Molex Power Connector 2 FCI Power Blade SD-87667 series 51761-10002406AALF 87667-7002 Right Angle Pin Assignments Pin Assignments Pin Signal Name Pin Signal Name 2 PB 1 Main output return C1 SDA (I C Data Signal) 2 PB 2 Main output return C2 SCL (I C Clock Signal)* PB 3 Main output return C3 POWER GOOD PB 4 + Main output C4 Spare PB 5 + Main output C5 STAND-BY PB 6 + Main output C6 STAND-BY RETURN 2 A1 PS_ON D1 A0 (I C Address BIT 0 Signal) 2 D2 A1 (I C Address BIT 1 Signal) A2 Main output remote sense return A3 Spare D3 S_INT (Alarm) A4 PS_SEATED (Power Supply Seated) D4 STAND-BY RMT SENSE A5 STAND-BY D5 STAND-BY A6 STAND-BY RETURN D6 STAND-BY RETURN B1 AC_OK (AC Input Present) 2 *Supports I C standard mode (100 kHz) only B2 Main output remote sense B3 Main output current share B4 PS_INHIBIT/PS_Kill B5 STAND-BY B6 STAND-BY RETURN WORLDWIDE OFFICES americas europe (uK) asia (HK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street Kwun Tong, Kowloon USA West Midlands, DY5 1LX +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of For support: productsupport.ep@artesyn.com this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. DS1200 Series-DS 09.09.14 © 2014 Artesyn Embedded Technologies, Inc.

Frequently asked questions

Electronics Finder' parent company, GID Industrial, specializes in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. We stand apart from our competition through our commitment to quality, and look forward to the opportunity to show you how.

The warranty we offer will be based on what we negotiate with our suppliers. Sometimes, a part will be sold as-is and without a warranty. We usually offer a one-year warranty for single board computers in particular because they are our specialty.

We use FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. We are able to ship with other carriers if you would find it more convenient.

Electronics Finder will definitely serve you. We work with international clients all the time, which means we are regularly shipping goods all across the globe.

Visa, MasterCard, Discover, and American Express are all accepted by Electronics Finder. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may be offered (upon approval) for larger orders.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products