POWER DS1200HE Data Sheet 1200 Watts Distributed Power System Front-end Bulk Power Total Output Power: 180 to 264 Vac: 1200 W continuous 90 to 140 Vac: 1000 W/ 1 1200 W continuous SPECIAL FEATURES ƒ 1200 W output power ƒ High power ƒ 1U x 2U power supply 3 ƒ High density design: 21.66 W/in ƒ Active Power Factor Correction Electrical Specifications ƒ EN61000-3-2 Harmonic compliance Input ƒ Inrush current control 1 Input voltage range 90 - 140 Vac: 1000 W/1200 W ƒ 80plus Platinum efficiency 180 - 264 Vac: 1200 W ƒ N+1 or N+N redundant Frequency 47 Hz to 63 Hz ƒ Hot plug operation Efficiency 94.0% peak ƒ N + 1 redundant Max input current 15 Arms ƒ Active current sharing Inrush current 55 Apk at 240 Vac, cold start ƒ Full Digital control Conducted EMI Class B ƒ PMBus compliant Radiated EMI Class B ƒ Input power reporting Power factor 0.9 typical ƒ Compatible with Artesyn’s Universal ITHD 10% PMBus GUI Leakage current 1.4 mA ƒ Reverse airflow option Hold-up time 12 ms ƒ Two-year warranty 1 1000 W at forward air, 1200 W at reverse air. See power derating table COMPLIANCE Ordering Information ƒ Conducted/Radiated EMI Class B DS1200HE-3 12 V / 100 A, 3.3 Vsb / 6 A, standard airflow ƒ RoHS DS1200HE-3-002 12 V / 100 A, 5.0 Vsb / 4 A, standard airflow DS1200HE-3-003 12 V / 100 A, 3.3 Vsb / 6 A, reverse airflow SAFETY DS1200HE-3-004 12 V / 100 A, 5.0 Vsb / 4 A, reverse airflow ƒ UL/cUL 60950 (UL Recognized) ƒ NEMKO+ CB Report EN60950 ƒ CE Mark ƒ China CCC DS1200HE Data Sheet Electrical Specifications Output Main DC Output MIN NOM MAX Nominal setting -0.50% 12 0.50% Total output regulation range 11.4 V 12.6 V Dynamic load regulation range 11.4 V 12.6 V Output ripple 120 mVp-p 4 Output current 0 A 100.0 A Current sharing Within ±5% of full load ratin Capacitive loading 2,000 uF 40,000 uF Start-up from AC to output 2000 ms Output rise time 5 ms 50 ms Standby DC Output (VSB) Output setpoint range -1% 3.3 V (5.0 V) 1% Total output regulation range +5% -5% Dynamic load regulation range +5% -5% Output ripple 50 mVp-p Output current 0 6.0 A (4 A) N/A Current sharing Capacitive loading 0 uF 680 uF Start-up from AC to output 1000 ms Output rise time 2 ms 50 ms Protections Main Output 2 Overcurrent protection 120% 150% 1 Overvoltage protection 13.5 V 15.0 V Undervoltage protection 10.5 V 11.0 V Overtemperature protection Yes Fan fault protection Yes Standby Output 3 Overcurrent protection 3 Overvoltage protection 1 Latch mode 2 Autorecoverys if the overcurrent is less than 130% and last only for <1000 ms. Otherwise, latch mode 3 Standby protection is auto-recovery 4 For output transient testing, the minimum load shall be at 10 A DS1200HE Data Sheet Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. A 100pF decoupling capacitor is recommended at the system side. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK PSKILL_L First break/last mate active LOW signal which enables/disables the main output. This signal will have to be pulled to ground at the system side with a 220 ohm resistor. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK VSENSE+, VSENSE-, STBY_VSENSE+ VSENSE+, VSENSE-, and STBY_VSENSE+ lines are the remote sense lines for regulation. Each line will compensate for a maximum of 100 mV. Output Signals ACOK_L Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor at the system side. MIN MAX V Output logic level LOW 0.6 V IL V Output logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK PWR_GOOD / PWOK_H Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 10 kohm resistor. MIN MAX V Output logic level LOW 0.8 V IL V Output logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK DS1200HE Data Sheet Control and Status Signals Output Signals PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is connected to ground via a 220 ohm resistor within the power supply PS_INTERRUPT Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP, OCP, OTP, and fan fault. This signal can be cleared by a CLEAR_FAULT command. A 100pF decoupling capacitor is recommended. MIN MAX V Output logic level LOW 0.8 V IL V Output logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin at low state 4 mA SINK BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX I Voltage Voltage at 100% load, stand-alone unit 7.65 8.35 SHARE Voltage at 50% load, stand-alone unit 3.65 4.35 Voltage at 0% load, stand-alone unit 0 0.5 I Current that may be sourced by this pin 160 mA SOURCE SCL, SDA 2 Clock and data signals defined as per I C requirements. It is recommended that these pins be pulled-up to a 2.2 kohm resistor to 3.3 V and a 100 pF decoupling capacitor at the system side. MIN MAX V Logic level LOW 0.8 V L V Logic level HIGH 2.0 V 5.0 V H Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. 2 I C Addressing Table PMBUS ADDRESSING Electrical Specifications A1 A0 Address LOW LOW 0 x B0 LED Indicators LOW HIGH 0 x B2 A single bi-color LED is used to indicate the power supply status. HIGH LOW 0 x B4 Status LED HIGH HIGH 0 x B6 No AC input to PSU Off AC present, STBY ON, main output OFF Blinking GREEN Main output ON Solid GREEN Over-voltage/Under-voltage failure Blinking AMBER Power supply failure (OVP, OTP, FAN FAULT) Solid AMBER DS1200HE Data Sheet Firmware Reporting And Monitoring MIN/MAX Output loading 5 to 20% 20% to 50% 50% to 100% Input voltage ±5% Input current ±0.7 A fixed error ±5% Input power ±10 W at <125 W input ±5% Output voltage ±4% Output current 0.5 A fixed error ±5% Temperature ±5 degC on the operating range Fan speed Actual ±250 RPM PMBus YES Remote ON/OFF YES Timing Specifications Description Min Max Unit T Delay from AC being applied to standby output being within regulation 1700 ms sb_On T Delay from AC being applied to main output being within regulation 2000 ms AC_On_Delay T Delay from output voltages within regulation limits to PWOK asserted 100 1000 ms PWOK_On T Delay from loss of AC to assertion of ACOK 7 14 ms ACOK_Delay T Delay from loss of AC to deassertion of PWOK 11 ms PWOK_Hold-up T Delay from loss of AC to main output being within regulation 12 ms Vout_Hold-up T Delay from loss of AC to standby output being within regulation 400 ms sb_Hold-up T Delay from deassertion of PWOK to output falling out of regulation 1 ms PWOK_Off T Delay from PSON assertion to output being within regulation 350 ms PSON_On_Delay T Delay from deassertion of PWOK to output falling out of regulation 1 ms PWR_GOOD_Off T Delay from PSON assertion to output being within regulation 350 ms PSON_On_Delay Environmental Specifications Operating temperature -10 to 50 °C, can provide derated power up to 70 °C. See power derating curve Operating altitude Up to 10,000 feet Operating relative humidity 10% to 90% non-condensing Non-operating temperature -40 to +85 °C Non-operating relative humidity 10% to 95% non-condensing Non-operating altitude Up to 50,000 feet Vibration and shock Standard oprating/non-operating random shock and vibration ROHS compliance Yes MTBF 200,000 hours using Bell Core TR-332, issue 6 specification, Method 1 Case 3 at 25 degC ambient at full load. Operating life Minimum of 5 years Reliability All electronic component derating analysis and capacitor life calculation is done as per Artesyn Network Power standards. The QAV report will be available upon request. DS1200HE Data Sheet Timing Diagram AC Input T T sb_Hold-up sb_On T ACOK_Delay Vout_stby T sb_Vout ACOK T T AC_On_Delay Vout_Hold-up T PWOK_Off Vout_main T PWOK_On T PWOK_Off PWOK T PWOK_Hold-up T PSON_On_Delay PSON DS1200HE Data Sheet Power Derating Curve FORWARD AIRFLOW REVERSE AIRFLOW Power versus Temperature Power versus Temperature 1400 1400 1200 1200 1000 1000 800 800 600 600 High Line High Line 400 400 Low Line Low Line 200 200 0 0 01 02 03 04 05 06 07 08 0 01 02 03 04 05 06 07 08 0 Ambient Temperature Ambient Temperature Mechanical Specifications Output Power Output Power DS1200HE Data Sheet Mechanical Specifications DC Output Connector Pinout Assignment Male connector as viewed from the rear of the supply: Pin Assignments D1 D2 D3 D4 D5 D6 Pin Signal Name C1 C2 C3 C4 C5 C6 PB1 PB2 PB3 PB4 PB5 PB6 B1 B2 B3 B4 B5 B6 PB1 Main output return A1 A2 A3 A4 A5 A6 PB2 Main output return PB3 Main output return Power Supply Side PB4 + Main output 1. FCI Power Blade 51721 series PB5 + Main output 51721-10002406AA PB6 + Main output 2. Molex Power Connector SD-87667 series A1 PSON_L 87667-7002 A2 Main output remote sense return, VSENSE- Mating Connector (System Side) A3 Spare 1. FCI Power Blade A4 PS_PRESENT 51741-10002406CC A5 STAND-BY, +VSB Straight Pins 2. FCI Power Blade A6 STAND-BY RETURN, -VSB 51761-10002406AALF B1 ACOK_H (AC Input Present) Right Angle B2 Main output remote sense, VSENSE+ 3. Any other approved equivalent B3 ISHARE B4 PS_INHIBIT / PSKILL_Ll B5 STAND-BY B6 STAND-BY RETURN 2 C1 SDA (I C Data Signal) 2 C2 SCL (I C Clock Signal) C3 POWER GOOD/ PWOK_H C4 Spare C5 STAND-BY, +VSB C6 STAND-BY RETURN 2 D1 A0 (I C Address BIT 0 Signal) 2 D2 A1 (I C Address BIT 1 Signal) D3 PS_INTERRUPT (Alarm) D4 STAND-BY RMT SENSE, VSENSE_STBY D5 STAND-BY, +VSB D6 STAND-BY RETURN, -VSB WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. DS1100HE 28Jun2016