POWER DS1600SPE Data Sheet 1600 Watts Distributed Power System Front-end Bulk Power Total Output Power: 1600 W continuous at high line Wide Range Input Voltage: 90 - 264 Vac SPECIAL FEATURES ƒ 1600 W output power at high line ƒ High power and short form factor ƒ 1U power supply 3 ƒ High density design: 40 W/in ƒ Active power factor correction ƒ EN61000-3-2 harmonic compliance ƒ Inrush current control Electrical Specifications ƒ 80plus platinum efficiency Input ƒ N+1 or N+N redundant Input voltage range 180 to 264 Vac: 1600 W 90 to 140 Vac: 800 W ƒ Active current sharing ƒ Full digital control Frequency 47 Hz to 63 Hz ƒ PMBus compliant Efficiency 94.0% peak ƒ Compatible with Artesyn’s universal Max input current 10.8 Arms PMBus GUI Inrush current 55 Apk ƒ Reverse airflow option Conducted EMI Class A ƒ Two-year warranty Radiated EMI Class A Power factor > 0.9 beginning at 20% load COMPLIANCE ITHD 10% ƒ Class A + 6 dB margin Conducted/ Leakage current 1.75 mA Radiated EMI Hold-up time 10 ms ƒ RoHS compliant SAFETY Ordering Information ƒ UL/cUL 60950 (UL Recognized) Model Number Nominal Main Output Standby Output Airflow Direction ƒ NEMKO+ CB Report EN60950 DS1600SPE-3 12 V @ 133.3 A 12 V @ 3.5 A Standard (forward) ƒ EN60950 DS1600SPE-3-001 12 V @ 133.3 A 12 V @ 3.5 A Reverse ƒ CE Mark ƒ China CQC DS1600SPE Data Sheet Electrical Specifications Output Main DC Output MIN NOM MAX Nominal setting -0.20% 12 0.20% Total output regulation range 11.4 V 12.6 V 5 Dynamic load regulation range 11.4 V 12.6 V Output ripple 150 mVp-p 4 Output current 2 A 133.33 A Current sharing Within +/-5% of full load rating Capacitive loading 2,250 µF 14,000 µF Start-up from AC to output 2,300 ms Output rise time 2 ms 60 ms Standby DC Output Nominal setting -3% 12 3% Total output regulation range 11.4 V 12.6 V Dynamic load regulation range 11.4 V 12.6 V Output ripple 150 mVp-p Adjustment range N/A 4 Output current 0.1 A 3.5 A N/A Current sharing Capacitive loading 47 µF 1,000 µF Start-up from AC to output 20 ms 2,000 ms Output rise time 2 ms 60 ms Protections Main Output 2 Overcurrent protection 115% 150% 1 Overvoltage protection 13.5 V 15.0 V Undervoltage Protection 10.5 V 11.0 V Overtemperature protection Yes Fan fault protection Yes Standby Output 3 Overcurrent Protection 120% 150% 1 Overvoltage Protection 13.5 V 15.0 V Undervoltage Protection 10.0 V 11.0 V 1 Latch mode 2 Autorecovery if the overcurrent is less than 115% and last only for <500 ms 3 Standby protection is auto-recovery 4 Minimum current for transient load response testing only. Unit is designed to operate and be within output regulation range at zero load. 5 Maximum step size of 67 A at 0.5A/µs, with a beginning load of 8 A, and 3,350 µF capacitance DS1600SPE Data Sheet Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. System Side pull-up resistor is not required. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK PSKILL_H First break/last mate active HIGH signal which enables/disables the main output. This signal will have to be pulled to ground at the system side. MIN MAX V Input logic level LOW. This allows for the power supply to 0.8 V IL be tunred on V Input logic level HIGH. Immediately shuts down the power 2.0 V 5.0 V IH supply I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK VSENSE+, VSENSE- VSENSE+ and VSENSE- lines are the remote sense lines for regulation. Each line will compensate for a maximum of 200 mV. Output Signals ACOK Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX V Output logic level LOW 0.6 V IL V Output logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 1.0 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 10 kohm resistor. MIN MAX V Output logic level LOW 0.8 V IL V Output logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK DS1600SPE Data Sheet Control and Status Signals Output Signals PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is shorted to the standby return in the power supply. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. PS_INTERRUPT Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP, OCP, OTP, and fan fault. This signal can be cleared by a CLEAR_FAULT command. Recommended pull-up resistor to 12 VSB is 8.2 k with a 3.0 k pull-down to ground. A 100 pF decoupling capacitor is also recommended. MIN MAX V Output logic level LOW 0.8 V IL V Output logic level HIGH 2.0 V 5.0 V IH I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin at low state 4 mA SINK BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX I Voltage Voltage at 100% load, stand-alone unit 7.75 8.25 SHARE Voltage at 50% load, stand-alone unit 3.85 4.15 I Current that may be sourced by this pin 160 mA SOURCE SCL, SDA, A0, A1, A2 Clock, data and addressing signals defined as per I2C requirements. It is recommended that these pins be pulled-up to a 2.2 kohm resistor to 3.3 V and a 22 pF decoupling capacitor at the system side. MIN MAX V Logic level LOW 0.8 V L V Logic level HIGH 2.0 V 5.0 V H Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. 2 I C Addressing Table A2 A1 A0 PMBus (W/R) FRU (W/R) 0 0 0 B0/B1 A0/A1 0 0 1 B2/B3 A2/A3 0 1 0 B4/B5 A4/A5 0 1 1 B6/B7 A6/A7 1 0 0 B8/B9 A8/A9 1 0 1 BA/BB AA/AB 1 1 0 BC/BD AC/AD 1 1 1 BE/BF AE/AF DS1600SPE Data Sheet Electrical Specifications LED Indicators A single bi-color LED is used to indicate the power supply status. Status LED No AC input to PSU Off Main output ON Solid GREEN Standby mode and Power supply failure (OCP, OVP, OTP, FAN FAULT) Blinking AMBER Firmware Reporting And Monitoring Accuracy Range Output loading 8 to 20% 20% to 50% 50% to 100% Input voltage ±5% Input current ±0.55A ±5% Input power ±5W at <125 W input power ±1.25% Output voltage ±2% Output current ±1.2 A fixed error ±3% Temperature ±5 degC on the operating range E ±15% from 10% to 20% load ±5% IN Fan speed ±250 RPM PMBus YES Remote ON/OFF YES DS1600SPE Data Sheet Electrical Specifications Timing Specifications Description Min Max Unit T Delay from AC being applied to standby output being within regulation 20 2000 ms sb_On T Delay from standby output to ACOK assertion See note below 20 ms sb_ACOK T Delay from standby output to main output voltage being within regulation 300 ms sb_Vout T Delay from AC being applied to main output being within regulation 2300 ms AC_On_Delay T Delay from output voltages within regulation limits to PWOK asserted 100 1000 ms PWOK_On T Delay from loss of AC to assertion of ACOK 7 ms ACOK_Delay T Delay from loss of AC to deassertion of PWOK 10 ms PWOK_Hold-up T Delay from loss of AC to main output being within regulation 11 ms Vout_Hold-up T Delay from loss of AC to standby output being within regulation 150 ms sb_Hold-up T Delay from deassertion of PWOK to output falling out of regulation 1 ms PWR_GOOD_Off T Delay from PSON assertion to output being within regulation 150 ms PSON_On_Delay T Duration of PWOK being in deasserted state during an ON/OFF cycle of PSU N/A N/A PWOK_Low Note: T : tested at 1A load on standby output sb_hold-up T : ACOK can assert earlier than the standby output sb_ACOK Timing Diagram AC Input T T sb_Hold-up sb_On T ACOK_Delay Vout_stby T sb_Vout T sb_ACOK ACOK T T AC_On_Delay Vout_Hold-up Vout_main T PWOK_On T PWOK_Off PWOK T PWOK_Hold-up T PSON_On_Delay PSON DS1600SPE Data Sheet Mechanical Outline 191.1±0.5 (14.8) 6±0.3 A 8.8±0.5 9.3±0.4 C +0.9 40.25±0.7 38.5 -0.5 B (4) 196.5 C DIM AND TOL NEED TO BE HELD AT THE EDGE OF THE STANDOFF LOCATIONS ONLY. MODEL AIRFLOW DIRECTION DS1600SPE-3 FORWARD DS1600SPE-3-001 REVERSE 40.2±0.5 86.3±0.5 B A DS1600SPE Data Sheet Output Connector Pin Configuration Connector Definitions S1 PS_PRESENT S13 PS_ON_L Output Connector Part Number Card-edge S2 A1 S14 PSKILL_H Mating Connector Part Number FCI 10107844-002LF or any equivalent S3 A0 S15 RESERVED S4 PWR_GOOD (PWOK) S16 RTN Power Supply Output Card Edge (Bottom Side) S24 S13 S5 ACOK (AC Input Present) S17 SDA . . S6 RTN S18 RTN P29-P36 P21-28 . S7 I_SHARE S19 SCL P19/20 S8 RESERVED S20 RTN S9 PS_INTERRUPT_L S21 REMOTE SENSE - S10 RETURN S22 RTN Power Supply Output Card Edge (Top Side) S11 RESERVED S23 REMOTE SENSE + S12 RESERVED S24 A2 P1-P8 +12VOUT P19-P20 +VSB P1-P8  P9-P18 . . P9-P18 RETURN P21-P28 RETURN S1 S12 P29-P36 +12VOUT Environmental Specifications Operating temperature Ds1600SPE-3: 1600W from 0 to 50 °C, can operate up to 65°C at 2% derated power for every °C above 50°C DS1600SPE-3-001: 1600W from 0 to 40°C, can operate up to 60°C at 1% derated power for every °C above 40°C Operating altitude up to 16,400 feet, derated after 10,000 feet Operating relative humidity 5% to 95% non-condensing Non-operating temperature -40 to +70 °C Non-operating relative humidity 5% to 95% non-condensing Non-operating altitude up to 50,000 feet Vibration and shock Standard operating and non-operating random shock and vibration ROHS compliance Yes MTBF 1,100,000 hours using Bell Core TR-332, issue 6 specification, Method 1 Case 3 at 25 °C ambient at full load. Operating life Minimum of 5 years WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. DS1600SPE 01Jul2016