POWER DS2000SPE Series Data Sheet 2000 Watts Distributed Power System Front-end Bulk Power Total Output Power: 2000 W continuous at high line 90-140 V &180-264 Vac Operation SPECIAL FEATURES ƒ 2000 W output power at high line ƒ High power and short form factor ƒ 1U power supply 3 ƒ High density design: 50 W/in ƒ Active power factor correction ƒ Inrush current control Electrical Specifications ƒ 80plus platinum efficiency Input ƒ N+1 or N+N redundant Input voltage range 180 to 264 Vac: 2000 W ƒ Active current sharing 90 to 140 Vac: 1000 W ƒ PMBus compliant Frequency 47 Hz to 63 Hz ƒ Two-year warranty Efficiency 94.0% peak Max input current 11.5 Arms at 100/200 Vac COMPLIANCE Inrush current 50 Apk ƒ Class A Conducted/Radiated EMI Conducted EMI Class A ƒ RoHS Radiated EMI Class A Power factor > 0.9 beginning at 20% load SAFETY ITHD 10% ƒ UL/cUL 60950 (UL Recognized) Leakage current 1.0 mA ƒ DEMKO+ CB Report EN60950 Hold-up time 11 ms at 95% load ƒ EN60950 ƒ CE Mark Ordering Information Model Number Nominal Main Output Standby Output Airflow Direction DS2000SPE-3 12.2 V @ 163.9 A 12 V @ 3.5 A Standard (forward) TBD 12.2 V @ TBD 12 V @ 3.5 A Reverse DS2000SPE Data Sheet Electrical Specifications Output Main DC Output MIN NOM MAX Nominal setting 12.175 12.2 12.225 Total output regulation range 11.4 V 12.9 V Dynamic load regulation range 11.4 V 12.9 V Output ripple 180 mVp-p 1, 2 Output current 5.0 A (minimum starting load for 163.9 A at high line 17% transient step) 82 A at low line Current sharing Within +/-7.0 A of each other Capacitive loading 4,900 µF 38,000 µF Start-up from AC to output 2,300 ms Output rise time 100 ms Standby DC Output Nominal setting 11.95 12 12.05 Total output regulation range 11.4 V 12.6 V Dynamic load regulation range 11.4 V 12.6 V Output ripple 120 mVp-p Adjustment range N/A Output current 0.0 A 3.5 A Current sharing N/A Capacitive loading 1 µF 4700 µF Start-up from AC to output 20 ms 2000 ms Protections Main Output 3 Overcurrent protection 107% 130% 3 Overvoltage protection 13.5 V 14.5 V Undervoltage Protection 10.0 V 10.5 V 4 Overtemperature protection Yes 4 Fan fault protection Yes Standby Output 4 Overcurrent protection 110% 150% 3 Overvoltage protection 13.5 V 15.0 V 4 Undervoltage protection 10.0 V 10.5 V 1 Minimum current for transient load response testing only. Unit is designed to operate and be within output regulation range at zero load 2 Output voltage will stay within regulation during a 50% step load with a minimum starting load of 41A 3 Latch mode 4 Auto-recovery DS2000SPE Data Sheet Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.6 V IH I Current that may be sourced by this pin 1.0 mA SOURCE I Current that may be sunk by this pin at low state 4.0 mA SINK PSKILL_H First break/last mate active HIGH signal which enables/disables the main output. MIN MAX V Input logic level LOW. 0.8 V IL This allows for the power supply to be turned on V Input logic level HIGH. 2.0 V 3.6 V IH Immediately shuts down the power supply I Current that may be sourced by this pin SOURCE I Current that may be sunk by this pin at low state 4.0 mA SINK VSENSE+, VSENSE- VSENSE+ and VSENSE- lines are the remote sense lines for regulation. Each line will compensate for a maximum of 100 mV. Output Signals ACOK Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost MIN MAX V Output logic level LOW 0.4 V OL V Output logic level HIGH 2.4 V 3.6 V OH I Current that may be sourced by this pin 2.0 mA SOURCE I Current that may be sunk by this pin at low state 4.0 mA SINK PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. MIN MAX V Output logic level LOW 0.4 V OL V Output logic level HIGH 2.4 V 3.6 V OH I Current that may be sourced by this pin 2.0 mA SOURCE I Current that may be sunk by this pin at low state 4.0 mA SINK DS2000SPE Data Sheet Control and Status Signals Output Signals PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is connected to the standby return in the power supply. PS_INTERRUPT Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP, OCP, OTP, and fan fault. This signal can be cleared by a CLEAR_FAULT command. MIN MAX V Output logic level LOW 0.8 V OL V Output logic level HIGH 2.0 V 3.6 V OH I Current that may be sourced by this pin 2.0 mA SOURCE I Current that may be sunk by this pin at low state 4.0 mA SINK BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. I Voltage Min Max SHARE Voltage at 50% load, stand-alone unit 3.412 3.588 Voltage at 100% load, stand-alone unit 6.912 7.088 SCL, SDA 2 Clock, data and addressing signals defined as per I C requirements. It is recommended that these pins be pulled-up to a 2.0 kohm resistor to 3.3 V and a 100 pF decoupling capacitor at the system side. MIN MAX V Logic level LOW 0.8 V L V Logic level HIGH 2.0 V 3.6 V H Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. LED Indicators A single bi-color LED is used to indicate the power supply status. Status LED No AC input to PSU with external 12V Blinking AMBER Main output ON Solid GREEN Standby mode and Power supply failure (OCP, OVP, OTP, FAN FAULT) Blinking AMBER DS2000SPE Data Sheet Electrical Specifications Timing Specifications Description Min Max Unit T Delay from AC being applied to standby output being within regulation 20 2000 ms sb_On T Delay from standby output to ACOK assertion 20 ms sb_ACOK T Delay from standby output to main output voltage being within regulation 300 ms sb_Vout T Delay from AC being applied to main output being within regulation 2300 ms AC_On_Delay T Delay from output voltages within regulation limits to PWOK asserted 100 1000 ms PWOK_On T Delay from loss of AC to assertion of ACOK 7 ms ACOK_Delay T Delay from loss of AC to deassertion of PWOK 10 ms PWOK_Hold-up T Delay from loss of AC to main output being within regulation 11 ms Vout_Hold-up Delay from loss of AC to standby output being within regulation T 150 ms sb_Hold-up * Standby output loaded at 1.0 A T Delay from deassertion of PWOK to output falling out of regulation 1 ms PWR_GOOD_Off T Delay from PSON assertion to output being within regulation 350 ms PSON_On_Delay T Duration of PWOK being in deasserted state during an ON/OFF cycle of PSU N/A N/A PWOK_Low Timing Diagram AC Input T T sb_Hold-up sb_On T ACOK_Delay Vout_stby T sb_Vout T sb_ACOK ACOK T T AC_On_Delay Vout_Hold-up Vout_main T PWOK_On T PWOK_Off PWOK T PWOK_Hold-up T PSON_On_Delay PSON DS2000SPE Data Sheet Mechanical Outline EMI CLIP 185,4 0,3 14,8 0,3 HOT SURFACE 8,8 0,5 WARNING LABEL MODEL LABEL 196,5 0,5 FORWARD AIRFLOW DIRECTION FAN GUARD TO BE USED FOR REVERSE AIR MODELS ONLY LED INDICATOR REVERSE AIRFLOW DIRECTION 86,3 0,5 14 0,3 +0,4 40,1 -0,1 4 0,2 49,5 9,5 38,5 0,5 9,3 0,38 17,8 DS2000SPE Data Sheet Output Connector Pin Configuration Connector Definitions S1 PS_PRESENT S13 PS_ON_L Output Connector Part Number Card-edge S2 A1 S14 PSKILL_H Mating Connector Part Number FCI 10107844-002LF or any equivalent S3 A0 S15 RESERVED S4 PWR_GOOD (PWOK) S16 RETURN Power Supply Output Card Edge (Bottom Side) S5 ACOK (AC Input Present) S17 SDA S24 S13 S6 RETURN S18 RETURN . . P29-P36 P21-28 . S7 I_SHARE S19 SCL P19/20 S8 RESERVED S20 RETURN S9 PS_INTERRUPT_L / ALERT S21 REMOTE SENSE - S10 RETURN S22 RETURN Power Supply Output Card Edge (Top Side) S11 RESERVED S23 REMOTE SENSE + S12 RESERVED S24 A2 P1-P8 +12VOUT P19-P20 +VSB P1-P8  P9-P18 . . P9-P18 RETURN P21-P28 RETURN S1 S12 P29-P36 +12VOUT Environmental Specifications Operating temperature 0 to 50 °C, allowable up to 60 °C at derated output of 2.6%/°C above 50 °C Operating altitude 16,400 ft with derated power Operating relative humidity Up to 95% non-condensing Non-operating temperature -40 to +70 °C Non-operating relative humidity Up to 95% non-condensing Non-operating altitude up to 50,000 feet Vibration and shock Standard operating and non-operating random shock and vibration ROHS compliance Yes MTBF 900 khours Telcordia Issue 3 Operating life Minimum of 5 years WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. DS2000SPE 16Nov2016