POWER DS2500PE Data Sheet 180 Vac to 264 Vac 2500 W Distributed Power Bulk Front-end Single Ouptut Standard Total Output Power: 2500 W continuous SPECIAL FEATURES ƒ 2500 W output power ƒ High-power and narrow form factor ƒ 1U form factor 3 ƒ High-density design: 23.3 W/in ƒ Active Power Factor Correction ƒ EN61000-3-2 harmonic compliance ƒ Inrush current control ƒ 80plus platinum efficiency ƒ N+1 or N+N redundant Electrical Specifications ƒ Hot-pluggable Input ƒ Active current sharing Input voltage range 180 to 264 Vac ƒ PMBus compliant Frequency 47 Hz to 63 Hz ƒ Compatible with Artesyn’s universal Efficiency 94.0% peak PMBus GUI ƒ Two-year warranty Max input current 15.6 Arms Inrush current 55 Apk Conducted EMI Class A COMPLIANCE ƒ Class A +6 dB margin Conducted/ Radiated EMI Class A Radiated EMI Power factor >0.97, typical ƒ EN61000-4-11 ITHD 10% Leakage current 0.75 mA SAFETY Hold-up time 11ms ƒ UL/cUL 60950 (UL Recognized) ƒ DEMKO+ CB Report EN60950 ƒ EN60950 ƒ CE Mark ƒ BSMI DS2500PE Data Sheet Electrical Specifications Output Main DC Output MIN NOM MAX Nominal setting -0.20% 12 0.20% Total output regulation range 11.4 V 12.6 V Dynamic load regulation range 11.4 V 12.6 V Output ripple 120 mVp-p 5 Output current 2 A 208 A Current sharing Within +/-5% of full load rating Capacitive loading 1,000 µF 25,000 µF Start-up from AC to output 3000 ms Output rise time 5 ms 50 ms Standby DC Output Nominal setting -1% 3.3 V 1% Total output regulation range 3.135 V 3.465 V 1 Dynamic load regulation range 3.135 V 3.465 V Output ripple 50 mVp-p Output current 0.5 A 2.7 A N/A Current sharing Capacitive loading 47 µF 560 µF Start-up from AC to output 2500 ms Output rise time 2 ms 50 ms Protections Main Output MIN NOM MAX 2 Over-current protection 120% 150% 3 Over-voltage protection 13.5 V 15.0 V 3 Under-voltage Protection 9.6 V 11.0 V Over-temperature protection Yes Fan fault protection Yes Standby Output 4 Over-current Protection 120% 150% 3 Over-voltage Protection 13.5 V 15.0 V Under-voltage Protection 9.6 V 11.0 V 1 Dyanmic load limits will apply for 100 A step load at 0.5 A/us 2 Autorecovery if the overcurrent is less than 140% and last only for <1000 ms. Otherwise, immediate latch if the current is more than 140% 3 Latch mode 4 Autorecovery 5 Minimum starting current during transient load. Output stays within regulation range at zero load. DS2500PE Data Sheet Control and Status Signals Input Signals PSON Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.3 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK PSKIL First break/last mate active LOW signal which enables/disables the main output. This signal will have to be pulled to ground at the system side with a 220 ohm resistor. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.3 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK FAN_POWER Supplies the fan voltage to the power supply. These pins should be tied to the main 12 V output at the system side. MIN MAX I Current that may be sourced by this pin 0.8 V SOURCE A0, A1 2 Addressing pins of the power supply for I C communications. Refer to the addressing tables below. MIN MAX Internal pull-ups to 3.3V.It is recommended for the system R = 22 k ohm C = 47 pF to have pull-ups and decoupling on the address lines for better noise immunity. V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.3 V IH I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin 4 mA SINK Output Signals ACOK Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost. MIN MAX V Output logic level LOW 0.6 V IL V Output logic level HIGH 2.0 V 3.3 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. MIN MAX V Output logic level LOW 0.8 V IL V Output logic level HIGH 2.0 V 3.3 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK DS2500PE Data Sheet Control and Status Signals Output Signals PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. PS_INTERRUPT Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP, OCP, OTP, and fan fault. This signal can be cleared by a CLEAR_FAULT command. A 100 pF decoupling capacitor is recommended. MIN MAX V Output logic level LOW 0.8 V IL V Output logic level HIGH 2.0 V 3.3 V IH I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin at low state 4 mA SINK BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies configured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX I Voltage Input logic level LOW 7.75 8.25 SHARE Voltage at 50% load, stand-alone unit 3.85 4.15 Voltage at 0% load, stand-alone unit 0 0.3 I Current that may be sourced by this pin 160 mA SOURCE SCL, SDA 2 Clock, data and addressing signals defined as per I C requirements. The maximum system side resistor pull-up and decoupling capacitance MIN MAX V Logic level LOW 0.8 V L V Logic level HIGH 2.0 V 3.3 V H Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. 2 I C Addressing Table 2 A1 A0 Active Bus FRU EEPROM Address I C Address LOW LOW None Write 0 x A0h Write 0 x A0h LOW HIGH All “A” Read 0 x A1h Read 0 x A1h HIGH LOW All “B” HIGH HIGH None DS2500PE Data Sheet Electrical Specifications LED Indicators AC GOOD LED DC GOOD LED FAULT LED Color GREEN GREEN AMBER No AC input to PSU Off Off Off AC present, STBY ON, main output OFF On Off Off Main output ON On On Off Power supply failure (OVP, OTP, FAN FAULT) On Off Blinking Firmware Reporting And Monitoring Accuracy Range Output loading 5 to 20% 20 to 50% 50 to 100% Input voltage ±5% Input current ±0.55 A fixed error ±4% Input power ±10 W at <250 W input ±5% Output voltage ±2% Output current 2.5 A fixed error ±2% E ±15% from 10% to 20% load ±5% IN Fan speed ±250 RPM PMBus YES Remote ON/OFF YES Timing Specifications Description Min Max Unit T Delay from AC being applied to standby output being within regulation 2500 ms sb_On T Delay from standby output to main output voltage being within regulation 2000 ms sb_Vout T Delay from ACOK being asserted to standby output being within regulation 1500 ms sb_ACOK T Delay from AC being applied to main output being within regulation 3000 ms AC_On_Delay T Delay from output voltages within regulation limits to PWOK asserted 900 1100 ms PWOK_On T Delay from loss of AC to assertion of ACOK 10 ms ACOK_Delay T Delay from loss of AC to deassertion of PWOK 10 ms PWOK_Hold-up T Delay from loss of AC to main output being within regulation 12 ms Vout_Hold-up T Delay from loss of AC to standby output being within regulation 50 ms sb_Hold-up T Delay from ON command to output being within regulation 500 ms PS_ON_Delay T & T Delay from OFF command to output falling out of regulation and PWOK going low 0.3 ms PWOK_Off PS_OFF_Delay DS2500PE Data Sheet Timing Diagram AC Input T T sb_Hold-up Tsb_On T ACOK_Delay Vout_stby T sb_Vout T sb_ACOK ACOK T PWOK_Off & T AC_On_Delay T T Vout_Hold-up PSON_On_Delay Vout_main T PWOK_On T PWOK_Off PWOK T T PWOK_Hold-up PSON_On_Delay ON OFF Command Command PSON DS2500PE Data Sheet Environmental Specifications Operating temperature 10 to 50 °C Operating altitude up to 10,000 feet Operating relative humidity 8% to 85% non-condensing Non-operating temperature -40 to +60 °C Non-operating relative humidity 5% to 95% non-condensing Non-operating altitude up to 50,000 feet Vibration and shock Standard operating/non-operating shock/vibration ROHS compliance Yes MTBF 400,000 hours per Telcordia SR332 Operating life Minimum of 5 years Reliability All electronic component derating analysis and capacitor life calculation is done at maximum ambient, 80% of maximum rated load, nominal input line voltage. Mechanical Outline DS2500PE Data Sheet Output Connector Pin Configuration Connector Definitions S1 FAN INPUT S16 RTN Output Connector Part Number Molex Ten60 Power 46437-1123 S2 FAN INPUT S17 PSKILL Mating Connector Part Number Molex ten60 Power 46562-1123 or any Molex recommended equivalent S3 FAN INPUT S18 3V3STBY S4 PRESENT_A S19 PRESENT_B S5 RESERVED S20 RTN S6 SCL_A S21 RESERVED S7 PWR_GOOD_A S22 ISHARE S8 ACOK_A S23 RTN S9 A0 S24 SCL_B S10 PS_INTERRUPT_A S25 PWR_GOOD_B S11 COMM_BUS_RESET_A S26 ACOK_B S12 SDA_A S27 A1 S13 RESERVED S28 PS_INTERRUPT_B S14 VSENSE- S29 COMM_BUS_RESET S15 VSENSE+ S30 SDA_B P1-P4 12 VOUT P5-P14 RTN WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use For support: productsupport.ep@artesyn.com of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. DS2500PE Rev. 27Mar2015