POWER Data Sheet DS460SDC-3 460 Watts Total Output Power: 460 Watts +12 Vdc Standby Output Wide Range Input Voltage: 40 - 72 Vac SPECIAL FEATURES ƒ Active power factor correction ƒ 1U X 2U form factor ƒ +12 Vdc output ƒ +12 Vdc standby ƒ Hot plug operation ƒ N + 1 redundant ƒ Active current sharing Electrical Specifications ƒ Built-in cooling fan 2 Input ƒ I C communication interface bus ƒ PMBus compliantInput ra nge 40 - 72 Vac ƒ EEPROM for FRU data Frequency DC ƒ Two year warranty Inrush current 50 A maximum inrush current Efficiency 90% typical at full load, nominal line SAFETY Conducted EMI FCC Subpart J EN55022 Class B ƒ UL/cUL 60950 (UL Recognized) Radiated EMI FCC Subpart J EN55022 Class B ƒ NEMKO 60950 Leakage current 0.15 mA ƒ Cb Certificate and report Hold up time 1 ms minimum ƒ CE Mark (LVD) Output Main DC voltage +12.3 V @ 36.0 A Standby +12 V @ 2.3 A Adjustment range Factory Set Regulation ±5% Overcurrent +12 Vdc; recover; Trip point 120% - 150% of rated current Overvoltage +12 Vdc; 13.2 - 14.4 Vdc +12 Vsb; 13.6 - 15.0 Vdc Turn-on delay < 2 seconds Main output rise time < 50 mS, monotonic rise DS460SDC-3 Data Sheet Logic Control PS_PRESENT (S4) Used to sense the number of power supplies in the system (operational or not) and provide hot plug insertion and removal functionality by controlling main outputs during hot plug insertion and removal by employing following circuitry. When the unit is removed from the system the fast shut down signal quickly turns OFF main outputs and discharges output capacitors. This signal is the shortest gold finger pin on the signal connector to allow for last make, first break configuration. PSOK (S6) Combined indicator of DC input and main 12 V DC output. This is a three level signal to indicate different stages as follows: DC not OK and DC not OK – Signal status shall be LOW (< 0.6 V) DC OK and DC not OK – Signal status shall be LOW (< 0.6 V) DC OK and DC OK – Signal status shall be HIGH (> 3.0 V) DC not OK and DC OK – Signal status shall be Middle Level (Between 2 V and 2.5 V) DC OK threshold is defined as when the 12 V output is greater than 11.5 V DC not OK threshold is defined as when the 12 V output is less than 11.4 V & greater than 11.3 V I-Mon (S7) Provides both the load sharing function (as a feedback for output regulation droop function) and 12 V output current information. PS INTERRUPT (S4) The signal behavior in response to certain operating condition changes in the power supply as defined in the Firmware Specification section. This signal shall be pulled up to maximum 5 V logic level external to the PS. PS ON (S8) Required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the main 12 V DC output. When this signal is not pulled low by the system, or left open, the 12 V output is turned off. This signal is pulled to a standby voltage by a pull-up resistor internal to the power supply. Refer to On/Off Timing for timing diagram in TRN. When in off or standby condition, the main 12 V DC output will be less than 50 mV with respect to output return. LED INDICATOR GREEN = DC input present, 12 V output & 12 V standby in regulation OFF = Overvoltage, overcurrent, overtemperature, undervoltage protection triggered. Environmental Specifications Operating temperature -10 °C to 50 °C Storage temperature -40 °C to +85 °C Altitude, operating 10,000 ft. Electromagnetic susceptibility/Input transients EN61000-4-2, 4-3, 4-4, -4-5, 4-6, 4-11 RoHS & lead-free compliant No tantalum caps Humidity 5 to 90% RH, non-condensing Shock and vibration specificatons Complies with Astec Std. Specifications, Q3205 MTBF (Demonstrated) 500K Hrs at full load, 50 °C Ordering Information Nominal Output Set Point Total Minimum Maximum Output Ripple Over Model Number Stand-by Air Flow Voltage Set Point Tolerance Regulation Current Current P/P Current DS460SDC-3 12.3 Vdc ± 0.2% ± 5% 1 A 36.0 A 120 mV 150% 12.0 V @ 2.3 A STD DS460SDC-3-001 12.3 Vdc ± 0.2% ± 5% 1 A 36.0 A 120 mV 150% 12.0 V @ 2.3 A REV *Overcurrent latches off if overcurrent lasts over 1 second, otherwise it is auto recovery. DS460SDC-3 Data Sheet Mechanical Drawings 243.2 MODEL LABEL 196.9 ± 0.65 LED INDICATOR 136.9 (2X) 11.2 9.9 3.0 8.0 EMI GASKET (8X) STANDARD AIR FLOW DIRECTION 198.1 ± 0.6 187.8 1.0 4.2 7.6 40.5 ± 0.7 9.5 70.86 7.8 ± 0.6 39.9 ± 0.5 86.4 ± 0.55 DS460SDC-3 Data Sheet Connector Definitions Earth Gr ound DC Input Connector Pin 1 DC+ Pin 2 DC- Pin 3 Earth Ground Output Connector - Power Blades PB1 V o PB2 V o Power Supply Output Card Edge (Top Side) PB3 V o PB4 RTN PB5 PB4 PB3 PB2 PB1 PB5 RTN PB6 RTN S8 S1 PB7 RTN PB8 RTN PB9 V o PB10 V o Output Connector - Signal Blades S1 VSB S2 VSB S3 Reserved S9 S16 Power Supply Output Card Edge (Bottom Si de) S4 PS INTERRUPT S5 PS PRESENT PB8 PB9 PB10 PB6 PB7 S6 PSOK S7 I-MON S8 PSON# S9 SCL S10 SDA S11 GND S12 ADD0 S13 ADD1 S14 ADD2 S15 RTN S16 RTN DS460SDC-3 Data Sheet Power/Signal Mating Connectors and Pin Types Reference On Power Supply Mating Connector or Equivalent DC Input Connector Terminal block Wire AWG #16 - #12 Molex 459840007 (top mount) Output Connector PCB card edge (0.062”) Molex 459841122 (bottom mount) WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street Kwun Tong, Kowloon USA West Midlands, DY5 1LX +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of For support: productsupport.ep@artesyn.com this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. DS460S-DS 09Jul2015 © 2015 Artesyn Embedded Technologies, Inc.