POWER DS760SL Series Data Sheet 760 Watts Bulk Front End Total Output Power: 760 Watts +5.0 Vdc Standby Special featureS ƒ 760 W output power ƒ 18.1 W/cu-in ƒ 1U X 54.5 mm form factor (slimline) ƒ N + 1 redundant ƒ Hot-swap ƒ Internal OR’ing ƒ 5.0 V housekeeping ƒ High efficiency 91% @ 230 Vac, Electrical Specifications 50% load Input ƒ Variable speed “smart fans” Input ra nge (operating) 90 - 264 Vac ƒ EMI Class A Input range (nominal) 115 / 230 Vac Input through IEC connector ƒ EN61000 Immunity Frequency 47 - 63 Hz ƒ Two year warranty Input fusing Internal 10 A fuses Both lines fused Inrush current < = 25 A peak Either hot or cold start SafetY Power factor 0.99 typical Meets EN61000-3-2 ƒ UL/cUL 60950-1 Harmonics Meets IEC 1000-3-2 requirements ƒ CSA 60950-1 Input current 8.8 A RMS max input current At 100 Vac ƒ VDE 60950-1 Holdup time 12 ms minimum for main O/P At full rated load ƒ China CCC 20 ms minimum for standby ƒ CB Scheme Report/Cert Undervoltage lockout 85 ± 2.5 Vac Turn-on voltage 80 ± 2.5 Vac Turn-off voltage Overvoltage lockout N/A Leakage current < 0.8 mA At 264 Vac On/Off power switch N/A Power line transient MOV directly after the fuse Environmental Specifications Operating temperature -10 ° to 50 °C Storage temperature -40 ° to 85 °C Cooling Internal fan (fan speed control) Operating relative humidity 5% to 95% non-condensing Altitude 10,000 feet RoHS compliant Yes DS760SL Series Data Sheet Efciency Curve 760 W DS Slim (STD Air) 92.0% 90.0% 88.0% 230 Vac, 50Hz 86.0% 115 Vac, 60Hz 84.0% 82.0% 80.0% 0.0 100.0 200.0 300.0 400.0 500.0 600.0 700.0 800.0 900.0 Output Power [W] Output Output rating 12 V @ 62.3 A; 748 W 90 - 264 Vac 5.0 Vsb @ 2.4 A; 12 W Setpoint 12.0 V Total regulation range 12 V ± 1% Line/load/transient when measured at output 5.0 Vsb ± 3% connector Rated load 760 W maximum No derating over operating temp range Minimum load 12 V @ 0.0 A No loss of regulation 5.0 Vsb @ 0.0 A Output noise (PARD) 100 mV Max P-P 12.0 V output 100 mV Max P-P 5.0 Vsb output Measured with a 0.1 uF ceramic and 10 uF tantalum capacitor on any output; 20 Mhz Output voltage overshoot 300 mV; 12 V main 1 A/uSec slew rate 200 mV; 5.0 standby Transient response < 250 uSec 50% load step @ 1 A/us Step load valid between 10% to 100% of output rating Recovery time to within 1% of set point at onset of transient Max units in parallel Up to 4 Short circuit protection To 120% of rated output Output to return Remote sense Compensation up to 100 MV Output isolation Standard per Safety Requirements Forced load sharing To within 10% of all shared outputs Digital sharing control Overload protection (OCP) 120% to 130% 12 V output 120% to 170% 5.0 Vsb output Overvoltage protection (OVP) 110% to 120% 12 V outpu 110% to 125% 5.0 Vsb output Overtemperature protection 10 - 15 ˚C above safe operating area Both PFC and output converter monitored Ordering Information O/P Voltage Set Point Total Minimum Maximum Output Stand-by Model Number Air Flow Set Point Tolerance Regulation Current Current Ripple P/P Voltage DS760SL-3 12.0 Vdc ± 0.2% ± 1% 0 A 62.3 A 120 mV 5.0 V @ 2.4 A Standard DS760SL-3-001 12.0 Vdc ± 0.2% ± 1% 0 A 50.0 A 120 mV 5.0 V @ 2.4 A Reverse DS760SL-3-002 12.0 Vdc ± 0.2% ± 1% 0 A 62.3 A 120 mV 3.3 V @ 2.4 A Standard DS760SL-3-003 12.0 Vdc ± 0.2% ± 1% 0 A 50.0 A 120 mV 3.3 V @ 2.4 A Reverse Efciency DS760SL Series Data Sheet Outputs - All Models Timing Diagram AC On AC Input AC On TPWOK_Off_ TVout_Holdup Main Vout TAC_On_Delay TPWOK_Off_ TPWOK_Off TPWOK_On TPWOK_Holdup TPWOK_On PWOK Tsb_on_delay TPSON_PWOK Tsb_On 5.0 Vsb Vout TPSON_On_Delay SB_Vout T PS_ON TACOK_Delay AC_OK PSON AC I nput ON / OFF ON / OFF Cycle Cycle DS760SL Series Data Sheet Outputs - All Models Turn On/Off Timing Item Description Min Max Units Tvout_rise +12 Output rise time 10 300 mSec Tvout_rise 5.0 Vsb output rise time 1 50 mSec Tsb_on_delay Delay from AC being applied to 5.0 Vsb being within regulation. 1500 mSec Tac_on_delay Delay from AC being applied to all output voltages being within regulation. 3000 mSec Tvout_holdup Time all output voltages, including 5.0 Vsb, stay within regulation after loss of AC. 12 mSec Tpwok_holdup Delay from loss of AC to de-assertion of PWOK 5 mSec Tpson_on_delay Delay from PSON# active to output voltages within regulation limits. 50 2500 mSec Tpson_pwok Delay from PSON# de-active to PWOK being de-asserted. 100 mSec Tacok_delay Delay from loss of AC input to de-assertion of ACOK#. 10 mSec Tpwok_on Delay from output voltages within regulation limits to PWOK asserted at turn on. 100 1000 mSec Tpwok_off Delay from PWOK de-asserted to 12 Vdc or 5.0 Vsb dropping out of regulation limits. 1 1000 mSec Tpwok_low Duration of PWOK being in the de-asserted state during an off/on cycle using AC or the PSON# signal. 100 mSec Tsb_vout Delay from 5.0 Vsb being in regulation to 12 Vdc being in regulation at AC turn on. 50 1000 mSec PSON # PWOK# (POWER GOOD) The PSON# signal is required to remotely turn on/off the power PPWOK is a power good signal and will assert HIGH when the supply. PSON# is an active low signal that turns on the +12 Vdc outputs are within the regulation limits. PWOK will be pulled LOW power rail. When this signal is not pulled low by the system, or left by the power supply to indicate when either output falls below open, the +12 Vdc output turns off. The 5.0 Vsb output remains regulation limits or when AC power has been removed for a time on. This signal is pulled to a standby voltage by a pull-up resistor sufficiently long so that power supply operation is no longer guaran- internal to the power supply. The power supply fan(s) shall operate teed. The start of the PWOK# delay time shall be inhibited as long at the lowest speed. as the +12 Vdc output is in current limit or the 5.0 Vsb output is below the regulation limit. PSON Signal Characteristics PWOK Signal Characteristics Signal Type Accepts an open collector/drain Signal Type Open collector/drain output input from the system. Pulled-up from power supply. Pullup to to the 5.0 Vsb located in power 5.0 Vsb external to the power supply. supply. PSON# = Low ON PWOK = High Power Good PWOK = Low Power Not Good PSON# = Open OFF MIN MAX MIN MAX Logic level low (power supply ON) 0 V 0.8 V To tLogic level low voltage, Ising = 4 mA 0 V 0.8 V Logic level high voltage, Isource = 200 µA 2.0 V 4.125 V Logic level high (power supply OFF) 2.0 V 4.125 V Sink current, PWOK = low 4 mA Source current, Vpson = low 4 mA Power up delay: Tpson_on_delay 5 msec 200 msec Source current, PWOK = high 2 mA DS760SL Series Data Sheet # PSKILL AC INPUT PRESENT INDICATOR (ACOK ) # The +12 Vdc output only from the power supply shall be disabled if The ACOK signal is used to indicate presence of AC input to the the PSKILL input is high and V Standby will continue to be power supply. This signal shall be connected to 5.0 Vsb through a provided, outputs may be enabled if this signal is low. The power resistor on the host system side. A logic “High” level on this signal supply includes a pull up to disable all outputs if this signal is open. shall indicate AC input to the power supply is present. A Logic PSKILL whall not be connectd during a hot insertion before all of “Low” on this signal shall indicate a loss of AC input to the power the other pins are connected. supply. ACOK# Signal Characteristics Signal Type Pull up to 5.0 Vsb through a STATUS INDICATIONS resistor in the See table below for Summary of Status signals, Ports and host system. Indicators. The condition column assumes 2 or more power PWOK = High Present supplies present and ON and 5.0 Vsb shared for management PWOK = Low Not Present interface. On the “Fan Blocked” condition, the assumption is that MIN MAX all outputs are within spec and not over temperature. This would Logic level low voltage, Isink = 4 mA 0 V 0.8 V be considered a “warning” condition. On the “Standby” condition, Logic level high voltage, Isink = 50 µA 2.0 V 4.125 V the system differentiates this state by knowing PS_ONL in # negated (requesting Standby). Sink current, PRESENT = low 4 mA # Sink current, PRESENT = high 50 µsec Status Indicators Status Signals Status Register Shutdown Register LED’s Condition ACOK/H PWOK/H PSON PWOK Fan-Fail AC-Loss 0-Temp 0-Current Fail AC DC Fail Normal Operation 1 1 1 1 0 0 0 0 0 On On Off V1 12 V Overcurrent 1 0 1 0 0 0 0 1 1 On Off On AC Input Fail 0 0 1 0 0 1 0 0 1 Off Off Off Fan Blocked or Running Under Speed. 1 1 1 1 0 0 0 0 0 On On Off O/P’s ok UV on V1 12 V and PS Has Latched Off 1 0 1 0 0 0 0 0 1 On Off On UV on Vsb +5.0 and PS Has Turned Off 1 0 1 0 0 0 0 0 1 On Off On OV on V1 12V or Vsb +5.0 & PS Has 1 0 1 0 0 0 0 0 1 On Off On Latched Off Over Temp and PS Has Turned Off 1 0 1 0 0 0 1 0 1 On Off On Fan Below Shutdown Limit 1 0 1 0 1 0 0 0 1 On Off On No Problems But PS is in Standby Mode 1 0 0 0 0 0 0 0 0 On Off Off S12 S24 S1 S13 DS760SL Series Data Sheet Pin Out Table Mechanical Drawing Pin Signal Name Pin 1 +12 V Pin 2 +12 V Pin 3 Ground Pin 4 Ground S1 +12 V Sense S2 +12 V RTN Sense S3 +12 V Current Share S4 SMB_ALERT/L S5 SDA S6 SCL* S7 PSKILL S8 PSON/L S9 PW_OK S10 PS_A1 S11 +5.0 V_STBY S12 +5.0 V_STBY S13 Reserved S14 PRESENT/L S15 PS_A0 S16 Reserved S17 Reserved for factory use S18 EEPROM_WP S19 ACOK/H S20 Not used S21 Not used S22 Reserved for factory use S23 +5.0 V_STBY S24 +5.0 V_STBY 2 * Supports I C standard mode (100 kHz) only Output Connector Top Side Ground Ground Reference On Power Supply Mating Connector or Equivalent P3 P4 AC Input Connector IEC60320-C14 IEC60320-C13 Output Connector MOLEX P/N 4598/4005 MOLEX P/N 45984-4343 P1 P2 Mating Connector Details +12V +12V P/N Molex 45984-4343 Bottom Side Current Rating 30 Mating Connector - Molex P/N 45984-4343 Receptacle Header Upper & Lower Blades Signal CKT 13 Signal 24 CKT Plug 1 Plug 2 No. of Contacts 4 Power Contacts, 24 Signal Contacts Top Row Top Row Bottom Row Bottom Row Signal CKT 1 *Note: The top side of the PSU Output Connector connects with the Bottom Row of the Mating Connector ex: PSU-S13  Mating Signal Ckt1 DS760SL Series Data Sheet BURN-IN 100% Burn-in at 45˚C, at 80 - 90% load. Duration of burn-in determined by Quality Assurance Procedures. MTBF The power supply has a minimum MTBF of 300K hours using the Bell core 332, issue 6 specification @ 25 ˚C and 40 ˚C, ambient, at full load. With the power supply installed in a system in a 25 ˚C ambient environment and operating at full load, capacitor life shall be 10 years, minimum for ALL electrolytic capacitors contained within this power supply. The power supply shall demonstrate a MTBF level of > 500,000 hours. QUALITy ASSURANCE Full QAV testing shall be conducted in accordance with Artesyn Embedded Technologies Standards with reports available upon request. WARRANTy Artesyn Embedded Technologies shall warrant the power supply to be free of defects in materials and workmanship for a minimum period of two years from the date of shipment, when operated within specifications. The warranty shall be fully transferable to the end owner of the equipment powered by the supply. WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. DS750PED DS 29Mar2018