POWER DS800SL Series Data Sheet 800 Watts Bulk Front End Total Output Power: 800 Watts +5.0 Vdc Standby SPECIAL FEATURES ƒ 800 W output power ƒ 19.05 W/cu-in ƒ 1U X 54.5 mm form factor (slimline) ƒ N + 1 redundant ƒ Hot-swap ƒ Internal OR’ing ƒ 5.0 V housekeeping ƒ High efficiency 92% @ 200 Vac, Electrical Specifications 50% load (Climate Savers Gold) Input ƒ Variable speed “smart fans” Input ra nge (operating) 90 - 264 Vac ƒ EMI Class B Input range (nominal) 115 / 230 Vac ƒ Available in two airflow directions Frequency 47 - 63 Hz Inrush current ≤ 40 A peak Either hot or cold start SAFETY Power factor 0.99 typical Meets EN61000-3-2 ƒ UL/cUL 60950 -1 Harmonics Meets IEC 1000-3-2 requirements ƒ CSA 60950-1 Input current 10.0 A RMS max input current At 100 Vac ƒ VDE 60950-1 Holdup time 10 ms minimum for main O/P At full rated load ƒ China CCC Undervoltage lockout 85 ± 3.0 Vac Turn-on voltage ƒ CB Scheme Report/Cert 80 ± 3.0 Vac Turn-off voltage Overvoltage lockout N/A Leakage current < 1.0 mA At 264 Vac On/Off power switch N/A Power line transient MOV directly after the fuse DS800SL Series Data Sheet Efciency Curve 800 W DS Slim 92.0% DS800SL-3-001 Power Derating 820 90.0% 800 780 88.0% 760 230 Vac, 50 Hz 740 86.0% 720 100Vac 115 Vac, 60 Hz 700 110Vac 84.0% 680 230Vac 660 82.0% 640 620 80.0% 0 10 20 30 40 50 0.0 100.0200.0 300.0400.0500.0 600.0700.0 800.0900.0 Ambient Temperature (degC) Output Power [W] Output Output rating 12 V @ 66.7 A; 800 W 90 - 264 Vac 5.0 Vsb @ 4 A; 20 W Setpoint 12.0 V Total regulation range 12 V ± 1% Line/load/transient when measured at output 5.0 Vsb ± 3% connector Rated load 800 W maximum No derating over operating temp range for forward air Minimum load 12 V @ 0.5 A No load operation shall not damage the power supply 5.0 Vsb @ 0.0 A Output noise (PARD) 120 mV Max P-P 12.0 V output 100 mV Max P-P 5.0 Vsb output Measured with a 0.1 uF ceramic and 10 uF tantalum capacitor on any output; 20 Mhz Output voltage overshoot 600 mV; 12 V main 1 A/uSec slew rate 250 mV; 5.0 standby Transient response +/-5% of regulation range 50% load step @ 1 A/us Step load valid between 10% to 100% of output rating Recovery time to within 1% of set point at onset of transient Max units in parallel Up to 6 Short circuit protection >130% of rated output Output to return Remote sense Compensation up to 100 mV Output isolation Standard per Safety Requirements Forced load sharing To within 10% of all shared outputs Digital sharing control Overload protection (OCP) 120% to 130% 12 V output 120% to 170% 5.0 Vsb output Overvoltage protection (OVP) 110% to 120% 12 V output 110% to 125% 5.0 Vsb output Overtemperature protection 10 - 15 ˚C above safe operating area Both PFC and output converter monitored Efciency Power Rating DS800SL Series Data Sheet Outputs - All Models Timing Diagram AC On AC On AC Input TPWOK_Off_ TVout_Holdup Main Vout TAC_On_Delay TPWOK_Off_ TPWOK_Off TPWOK_On TPWOK_Holdup TPWOK_On PWOK Tsb_on_delay TPSON_PWOK Tsb_On 5.0 Vsb Vou t TPSON_On_Delay TSB_Vout PS_ON TACOK_Delay AC_OK PSON AC I nput ON / OFF ON / OFF Cycle Cycle DS800SL Series Data Sheet Outputs - All Models Turn On/Off Timing Item Description Min Max Units Tvout_rise +12 Output rise time 5 300 mSec Tvout_rise 5.0 Vsb output rise time 1 50 mSec Tsb_on_delay Delay from AC being applied to 5.0 Vsb being within regulation. 2000 mSec Tac_on_delay Delay from AC being applied to all output voltages being within regulation. 4000 mSec Tvout_holdup Time all output voltages, including 5.0 Vsb, stay within regulation after loss of AC. 12 mSec Tpwok_holdup Delay from loss of AC to de-assertion of PWOK. 5 mSec Tpson_on_delay Delay from PSON# active to output voltages within regulation limits. 5 200 mSec Tpson_pwok Delay from PSON# de-active to PWOK being de-asserted. 50 mSec Tacok_delay Delay from loss of AC input to de-assertion of ACOK#. 5 12 mSec Tpwok_on Delay from output voltages within regulation limits to PWOK asserted at turn on. 100 1000 mSec Tpwok_off Delay from PWOK de-asserted to 12 Vdc or 5.0 Vsb dropping out of regulation limits. 1 1000 mSec Tpwok_low Duration of PWOK being in the de-asserted state during an off/on cycle using AC or the PSON# signal. 100 mSec Tsb_vout Delay from 5.0 Vsb being in regulation to 12 Vdc being in regulation at AC turn on. 50 1000 mSec PSON # PWOK# (POWER GOOD) The PSON# signal is required to remotely turn on/off the power PWOK is a power good signal and will assert HIGH when the supply. PSON# is an active low signal that turns on the +12 Vdc outputs are within the regulation limits. PWOK will be pulled LOW power rail. When this signal is not pulled low by the system, or left by the power supply to indicate when either output falls below open, the +12 Vdc output turns off. The Vsb output remains on. regulation limits or when AC power has been removed for a time This signal is pulled to a standby voltage by a pull-up resistor sufficiently long so that power supply operation is no longer internal to the power supply. The power supply fan(s) shall operate guaranteed. The start of the PWOK# delay time shall be inhibited at the lowest speed. as long as the +12 Vdc output is in current limit or the 5.0 Vsb output is below the regulation limit. PSON Signal Characteristics PWOK Signal Characteristics Signal Type Open collector/drain output Signal Type Accepts an open collector/drain input from the system. Pulled-up to the 5.0 from power supply. Pullup to 5.0 Vsb external to the power Vsb located in power supply. supply. PSON# = Low ON PWOK = High Power Good PSON# = Open OFF PWOK = Low Power Not Good MIN MAX MIN MAX Logic level low (power supply ON) 0 V 0.8 V To tLogic level low voltage, Ising = 4 mA 0 V 0.8 V Logic level high (power supply OFF) 2.0 V 5.2 V Logic level high voltage, Isource = 200 µA 2.0 V 5 .2V Source current, Vpson = low 4 mA Sink current, PWOK = low 4 mA Power up delay: Tpson_on_delay 5 msec 200 msec Source current, PWOK = high 2 mA PWOK delay: T 100 ms 1000 ms pwok_on PWOK rise and fall time 100 µsec Power down delay: T 1 msec 1000 msec pson_off DS800SL Series Data Sheet PSKILL # ACOK Signal Characteristics The +12 Vdc output only from the power supply shall be disabled Signal Type Pull up to 5.0 Vsb through a if the PSKILL input is high and V Standby will continue to be resistor in the host system. provided, outputs may be enabled if this signal is low. The power Present = High Present supply includes a pull up to disable all outputs if this signal is open. Present = Low Not Present PSKILL whall not be connected during a hot insertion before all of MIN MAX the other pins are connected. Logic level low voltage, Isink = 4 mA 0 V 0.8 V Logic level high voltage, Isink = 50 µA 2.0 V 5.2 V AC INPUT PRESENT INDICATOR (ACOK/L) # Sink current, PRESENT = low 4 mA The ACOK signal is used to indicate presence of AC input to the # Sink current, PRESENT = high 50 µsec power supply. This signal shall be connected to Vsb through a resistor on the host system side. A logic “Low” level on this signal shall indicate AC input to the power supply is present. A Logic “High” on this signal shall indicate a loss of AC input to the power supply. S12 S24 S1 S13 DS800SL Series Data Sheet STATUS INDICATIONS See table below for Summary of Status signals, Ports and Indicators. The condition column assumes 2 or more power supplies present and ON and 5.0 Vsb shared for management interface. On the “Fan Blocked” condition, the assumption is that all outputs are within spec and not over temperature. This would be considered a “warning” condition. On the “Standby” condition, the system differentiates this state by knowing PS_ONL in negated (requesting Standby). Status Indicators Status Signals Status Register Shutdown Register LED’s Condition ACOK/L PWOK/H PSON PWOK Fan-Fail AC-Loss 0-Temp 0-Current Fail AC DC Fail Normal Operation 0 1 1 1 0 0 0 0 0 On On Off V1 12 V Overcurrent 0 0 1 0 0 0 0 1 1 On Off On AC Input Fail 1 0 1 0 0 1 0 0 1 Off Off Off Fan Blocked or Running Under Speed. 0 1 1 1 0 0 0 0 0 On On Off O/P’s ok UV on V1 12 V and PS Has Latched Off 0 0 1 0 0 0 0 0 1 On Off On UV on Vsb +5.0 and PS Has Turned Off 0 0 1 0 0 0 0 0 1 On Off On OV on V1 12V or Vsb +5.0 & PS Has 0 0 1 0 0 0 0 0 1 On Off On Latched Off Over Temp and PS Has Turned Off 0 0 1 0 0 0 1 0 1 On Off On Fan Below Shutdown Limit 0 0 1 0 1 0 0 0 1 On Off On No Problems But PS is in Standby Mode 0 0 0 0 0 0 0 0 0 On Off Off Output Connector and Pin-out Table Pin Signal Name Pin 1 +12 V Pin 2 +12 V Top Side Pin 3 Ground Ground Ground Pin 4 Ground S1 +12 V Sense P3 P4 S2 +12 V RTN Sense S3 +12 V Current Share S4 SMB_ALERT/L S5 SDA P1 P2 S6 SCL* S7 PSKILL +12V +12V S8 PSON/L Bottom Side S9 PW_OK S10 PS_A1 S11 +5.0 V_STBY Note: Pin number may not necessarily match vendor’s pin number S12 +5.0 V_STBY assignment. Please follow the signal and number assignment as S13 Reserved indicated in this datasheet S14 PRESENT/L S15 PS_A0 S16 Reserved S17 Reserved for factory use S18 EEPROM_WP S19 ACOK/L S20 Not used S21 PS_A2 S22 V_STBY Remote Sense S23 V_STBY S24 V_STBY 2 * Supports I C standard mode (100 kHz) only DS800SL Series Data Sheet Mechanical Drawing BURN-IN 100% Burn-in at 45 ˚C, at 80-90% load. Duration of burn-in determined by Quality Assurance Procedures. MTBF The power supply has an MTBF of >400K hours using Telcordia SR-332 at full load, and 25 °C ambient. With the power supply installed in a system in a 25 ˚C ambient environment and operating at full load, capacitor life shall be 5 years, minimum for ALL electrolytic capacitors contained within this power supply. T QUALITY ASSURANCE Full QAV testing shall be conducted in accordance with Artesyn Embedded Technologies Standards with reports available upon request. WARRANTY Artesyn Embedded Technologies shall warrant the power supply to be free of defects in materials and workmanship for a minimum period of two years from the date of shipment, when operated within specifications. The warranty shall be fully transferable to the end owner of the equipment powered by the supply. WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Waterfront Business Park 14/F, Lu Plaza Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street www.artesyn.com USA West Midlands, DY5 1LX Kwun Tong, Kowloon +1 888 412 7832 United Kingdom Hong Kong +44 (0) 1384 842 211 +852 2176 3333 For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. Specifications are subject to change without notice. © 2017 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, DS800SL DS 26Sep2017 please visit www.artesyn.com/legal.