Embedded Power for Business-Critical Continuity Rev. 02.22.11_81 HPS3000 Series 1 of 8 HPS3000 Series 3000 Watts Distributed Power Bulk Front-End Single Output Special Features Electrical Specifications • 3000 W output power • 40 W/cu-in Input • Optional customer provided air Input ra nge (operating): 180 - 264 Vac • 1U x 3U form factor 90 - 140 Vac • N+1 Redundant Input range (nominal): 200 Vac Input through Card Edge Connection • Hot-swap on same end as DC output 110 Vac • Internal OR-ing Frequency: 47 to 63 Hz • 5 V housekeeping Input fusing: Internal 25 A fuses Both lines fused • High efficiency 89% @ 200 Vac, 100% load Inrush current: ≤40 A peak Either hot or cold start • Variable speed “smart fans” Power factor: 0.97 typical Meets EN61000-3-2 • Two year warranty Harmonics: Meets IEC 1000-3-2 @ 50% load requirements Input current: 19 A max input current Holdup time: 10 ms minimum At full rated load Leakage current: 1.4 mA At 240 Vac Power line transient: MOV directly after the fuse Compliance • POE Isolation • EMI Class B - EN55022, Level “A” @ 230 Vac • EN61000 Immunity Safety • UL/cUL 60950 • CSA 60950 • China CCC • Nemko TUV • CB Report • CSA 22.2 60950 Embedded Power for Business-Critical Continuity 230V ac E fficiency Rev. 02.22.11_81 230 Vac Efficiency HPS3000 Series 2 of 8 100.00 90.00 80.00 70.00 60.00 50.00 40.00 30.00 20.00 10.00 10 20 30 40 50 60 70 80 90 100 % of Total Ou tput Po we r Output Output rating 48 V @ 62.0 A 180 - 264 Vac 5 Vsb @ 3.0 A 48 V @ 29.4 A 90 - 140 Vac 5V @ 3 A 2 Set point 48 V Programmable 96-117% through I C serial bus Total regulation range 48 V ± 5% Line/load/transient when measured at output connection 5 Vsb ± 4% Rated load 3000 W maximum @ 200 Vac Input No derating over operating temp range 1500 W maximum @ 110 Vac Input Minimum load 48 V @ 0.0 A No loss of regulation 5 Vsb @ 0.0 A Output noise 480 mV max P-P 48 V output 100 mV max P-P 5 Vsb output Measured with a 0.1µF Ceramic and 10 µF Tantalum capacitor on any input Output voltage overshoot ± 5% maximum Nominal Voltage Setting Transient response 5% maximum deviation 50% load step @ 1 A/us Step load valid between 10% to 100% of output rating. Max units in parallel Up to 4 Total power in 1U 19” rack is 12 KW Short circuit protection 120% - 130% of rated output Output to return Output isolation Per POE specs >2000 Vac Forced load sharing Within 10% of all shared outputs Digital sharing control Over current protection (OCP)120% to 130% 48 V output 110% to 140% 5 Vsb output Over voltage protection (OVP)110% to 133% 48 V output 110% to 125% 5 Vsb output Over temperature protection 10 - 15 deg C above safe Both PFC and output converter monitored operating area 5 Vsb will operate under overtemperature condition. Built in hysteresis Environmental Specifications Vibration/Shock: Non-operational 5G Sine sweep from 5 Hz to 500 Hz, dwelling at resonant frequencies for 1 hour each Operating temperature: -10 ° to +40 °C Storage Temperature: -40 ° to +85 °C Cooling External fans with Fan Fail and Fan Speed control Operating Relative Humidity: 5% to 95% non-condensing Storage Relative Humidity: 5% to 95% non-condensing Operating Altitude Up to 10,000 feet above sea level Storage Altitude: Up to 30,000 feet above sea level RoHS Compliant: Yes Embedded Power for Embedded Power for Business-Critical Continuity Business-Critical Continuity Rev. 02.22.11_81 HPS3000 Series 3 of 8 Module Information (All units in mm) Embedded Power for Embedded Power for Business-Critical Continuity Business-Critical Continuity Rev. 02.22.11_81 HPS3000 Series 4 of 8 Pin Assignments Bottom Top Pin Pin 1 AC LINE 64 AC LINE 2 AC LINE 63 AC LINE 3 n.c. 62 n.c. 4 AC NEUTRAL 61 AC NEUTRAL 5 AC NEUTRAL 60 AC NEUTRAL 6 n.c. 59 n.c. 7 n.c. 58 n.c. 8 n.c. 57 n.c. 9 +48 Vdc out 56 +48 Vdc out 10 +48 Vdc out 55 +48 Vdc out 11 +48 Vdc out 54 +48 Vdc out 12 +48 Vdc out 53 +48 Vdc out 13 +48 Vdc out 52 +48 Vdc out 14 +48 Vdc out 51 +48 Vdc out 15 +48 Vdc out 50 +48 Vdc out 16 +48 Vdc RTN 49 +48 Vdc RTN 17 +48 Vdc RTN 48 +48 Vdc RTN 18 +48 Vdc RTN 47 +48 Vdc RTN 19 +48 Vdc RTN 46 +48 Vdc RTN 20 +48 Vdc RTN 45 +48 Vdc RTN 21 +48 Vdc RTN 44 +48 Vdc RTN 22 +48 Vdc RTN 43 +48 Vdc RTN 23 n.c. 42 n.c. 24 V_STBY 41 SYS_GND 25 Reserved 40 Reserved 26 PRESENT# 39 ACOK# 27 DCOK/PWOK# 38 SMBUS_ALERT_OUT 28 SDA 37 SCL 29 HVCC 36 A2 30 PSON# 35 PSKILL 31 #ALERT 34 A1 32 ISHARE 33 A0 Embedded Power for Business-Critical Continuity Rev. 02.22.11_81 HPS3000 Series 5 of 8 Timing Diagram AC On AC On AC Input T PWOK_Off_ T Vout_Holdup Main Vout T PWOK_Off_ T AC_On_Delay T PWOK_Off_ T PWOK_Off_ T PWOK_Off T PWOK_On PWOK T PWOK_Delay T PWOK_On PWOK_On T T PSON_PWOK T sb_On 3.3 V Vout T PSON_On_Delay T SB_Vout PS_ON T ACOK_Delay AC_OK PSON AC Input ON / OFF ON / OFF Cycle Cycle Embedded Power for Business-Critical Continuity Rev. 02.22.11_81 HPS3000 Series 6 of 8 Timing Signal Definitions Turn ON/OFF Timing Item Description Min Max Units Tvout_rise 48 V Output rise time 5 300 msec Tsb_on_delay Delay from AC being applied to 5 Vsb being within regulation. 1500 msec Tac_on_delay Delay from AC being applied to all output voltages being within 2000 msec regulation. Tvout_holdup Time all output voltages, including 5 Vsb, stay within regulation 10 msec after loss of AC. Tpwok_holdup Delay from loss of AC to de-assertion of PWOK 5 msec Tpson_on_delay Delay from PSON# active to output voltages within regulation 5 400 msec limits. Tpson_pwok Delay from PSON# de-active to PWOK being de-asserted. 50 msec Tacok_delay Delay from loss of AC input to de-assertion of ACOK#. 10 msec Tpwok_on Delay from output voltages within regulation limits to PWOK 100 1000 msec asserted at turn on. Tpwok_off Delay from PWOK de-asserted to 48 V dropping out of regulation 1 1000 msec limits. Tpwok_low Duration of PWOK being in the de-asserted state during an off/on 100 msec cycle using AC or the PSON# signal. Tsb_vout Delay from 5 Vsb being in regulation to 48 V being in 50 2000 msec regulation at AC turn on. Signals and Controls - All Models PSON # The PSON# signal is required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the 48 V power rail. When this signal is not pulled low by the system, or left open, the 48 V output turns off. The 5 Vsb output remains on. This signal is pulled to a standby voltage by a pull-up resistor internal to the power supply. The power supply fan(s) shall operate at the lowest speed. PSON# Signal Characteristic Signal Type Accepts an open collector/drain input from the system. Pulled-up to the 5 Vsb located in power supply. PSON# = Low ON PSON# = Open OFF MIN MAX Logic level low (power supply ON) 0 V 0.4 V Logic level high (power supply OFF) 2.40 V 3.40 V Source current, Vpson = low -- 4 mA Power up delay: Tpson_on_delay 5 msec 400 msec Embedded Power for Business-Critical Continuity Rev. 02.22.11_81 HPS3000 Series PWOK# (Power Good) 7 of 8 PWOK# is a power good signal and will be pulled LOW by the power supply to indicate that both the outputs are above the regulation limits of the power supply. When any output voltage falls below regulation limits or when AC power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed, PWOK will be de-asserted to a HIGH state. The start of the PWOK# delay time shall be inhibited as long as the 48 V output is in current limit or the 5 Vsb output is below the regulation limit. PSON# Signal Characteristic Signal Type Open collector/drain output from power supply. Pullup to 5 Vsb external to the power supply. PWOK = High ON PWOK = LOW OFF MIN MAX Logic level low voltage, Isink=4mA 0 V 0.8 V Logic level high voltage, Isource=200µA 2.0 V 4.80 V Sink current, PWOK = low 4 mA Source current, PWOK = high 2 mA PWOK delay: T 100 msec 1000 msec pwok on PWOK rise and fall time 100 µsec Power down delay: T 1 msec 1000 msec pwok off Power Supply Present Indicator (PRESENT#) The PRESENT# signal is primarily used to provide a mechanism by which the host system can sense the number of power supplies physically present (operational or not). This pin is connected to ground in the power supply. AC INPUT Present Indicator (ACOK#) The AC OK# signal is used to indicate presence of AC input to the power supply. This signal shall be connected to 5 Vsb through a resistor on the host system side. A logic “Low” level on this signal shall indicate AC input to the power supply is present. A Logic “High” on this signal shall indicate a loss of AC input to the power supply. Table 12 ACOK# Signal Characteristics Signal Type Pull-up to 5 Vsb through a resistor in the host system. PRESENT# = Low Present PRESENT# = High Not present MIN MAX Logic level low voltage, Ising=4mA 0 V 0.8 V Logic level high voltage, Isink=50µA 2.0 V 4.80 V Sink current, PRESENT# = Low 4 mA Source current, PRESENT# = High 50 µA Embedded Power for Business-Critical Continuity Rev. 02.22.11_81 HPS3000 Series 8 of 8 Americas 5810 Van Allen Way LED INDICATORS Carlsbad, CA 92008 USA There will be a green POWER LED (PWR) to indicate that AC is applied to the Telephone: +1 760 930 4600 PSU and standby voltage is available when blinking. This same LED should go Facsimile: +1 760 930 0698 solid when the 48 V output is enabled and operational. Europe (UK) There will be an Amber Power Supply Fail LED (FAIL) to indicate that the power Waterfront Business Park supply has failed and a replacement of the unit is necessary. Faults including Merry Hill, Dudley West Midlands, DY5 1LX UVP, OVP, OTP, or Fan Fail when PSON# is asserted “Logic Low” shall cause the United Kingdom amber LED to turn on. The LED can be turned off by recycling PSON# signal or Telephone: +44 (0) 1384 842 211 by an AC power interruption more than 1 second. The LED shall be off when Facsimile: +44 (0) 1384 843 355 PSON# is not asserted “Logic Low”. Refer to table 13 for conditions of the LED’s: Asia (HK) 14/F, Lu Plaza Table 13 2 Wing Yip Street Kwun Tong, Kowloon LED Indicators Hong Kong Power Supply Condition Power LED Fail LED Telephone: +852 2176 3333 (GREEN) (AMBER) Facsimile: +852 2176 3888 No AC power to PSU OFF OFF For global contact, visit: AC present / Standby Output On Blinking OFF www.Emerson.com/ Power supply 48 V output ON and OK ON OFF EmbeddedPower Power supply failure (includes OFF ON techsupport.embeddedpower@ overvoltage, overtemperature) emerson.com Current limit ON Blinking While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this MTBF information or for any errors or omissions. The power supply has a minimum MTBF of 300K hours using the Bell core 332, issue 6 specification @ 25 °C and 40 °C, ambient, at full load. With the power Emerson Network Power. supply installed in a system in a 25 °C ambient environment and The global leader in enabling business-critical continuity. operating at full load, capacitor life shall be 10 years, minimum for ALL electrolytic capacitors contained within this power supply. The power supply shall demonstrate a MTBF level of > 500,000 hours. AC Power Quality Assurance Connectivity Full QAV testing shall be conducted in accordance with Emerson Network DC Power Power Standards with reports available upon request. Embedded Computing Embedded Power Warranty Monitoring Emerson Network Power shall warrant the power supply to be free of defects in materials and workmanship for a minimum period of two years from the Outside Plant date of shipment, when operated within specifications. The warranty shall be Power Switching & Controls fully transferable to the end owner of the equipment powered by the supply. Precision Cooling Racks & Integrated Cabinets Ordering Information Services Surge Protection Main Output Model Number Main Output Standby Output Standby Current Current EmersonNetworkPower.com HPS3000-9 48 Vdc 62.0 A 5.0 V 3.0 A Emerson Network Power and the Emerson Network Power logo are trademarks and ser- vice marks of Emerson Electric Co. ©2011 Emerson Electric Co.