POWER Intelligent VS Power Data Sheet Up to 4920 Watts Total Power: Up to 4920 W TM Input Voltage: 85 - 264 Vac 380, 440 Vac 120 - 300 Vdc 1-Phase 3-Phase Color: "i" 100% Blue, 50% Magenta, Font: Minion Bold for VS 0% Yellow, 0% Black Minion italic for i ; size for each is the same "VS" - 100% Black Created on Mac # of Outputs: Up to 24 SPECIAL FEATURES ƒ Full medical EN60601 approval 2 ƒ Intelligent I C control Electrical Specifications ƒ Voltage adjustment on all outputs Input 2 (manual or I C) Input ra nge iVS1 & iVS3 90 - 264 Vac 1Ø; 120 - 300 Vdc ƒ Configurable input and output OK signals and indicators iVS6 & iVS8 170 - 264 Vac 3Ø ƒ Configurable inhibit/enable iVS8H 396 - 480 Vac rated at 4920 W DC output 3Ø ƒ Configurable output UP/DOWN 342 - 396 Vac rated at 4200 W DC output 3Ø sequencing Frequency 47 - 440 Hz ƒ High power density (12 W/cu-in) Inrush current 40 A peak maximum (soft start) ƒ Intelligent fan (speed control/fault Efficiency Up to 85% @ full case load status) ƒ uP controlled PFC input with active Power Factor 0.99 typ. meets EN61000-3-2 Inrush protection Turn-on time AC on 1.5 sec typical, inhibit/enable 150ms typical Programmable; 2 ƒ I C monitor of voltage, current, and 50 ms internal turn-on delay (Dual Output only) temperature EMI Filter CISPR 22/EN55022 Level “B”. Level “A” for iVS8H ƒ Programmable voltage, current limit, 2 Leakage current 500 µA max. @ 240 Vac; 47-63 Hz inhibit/enable through I C ƒ Optional extended hold-up module Radiated EMI CISPR 22/EN55022 Level “B”. Level “A” for iVS8H (SEMI F47 compliance) Holdover storage 10 ms minimum (independent of input Vac) additional 20 mSEC holdover ƒ Increased power density to 150% storage with optional HUP module (SEMI F47 compatible) ƒ Optional conformal coating AC OK > 5 ms early warning minutes before outputs lose regulation Full cycle ride thru ƒ Industrial temp range (-40 ºC to 70 ºC) (50 Hz). Programmable ƒ Uses standard iMP modules Harmonic distortion Meets EN61000-3-2 ƒ Field upgradeable firmware Isolation Meets EN60950 and EN60601 ƒ RoHS compliant Global inhibit / enable TTL, Logic “1” and Logic “0”; configurable Warranty 3 years SAFETY ƒ UL UL60950/UL2601 ƒ CSA CSA22.2 No. 234 Level 5 ƒ UV EN60950/EN60601-1 ƒ BABT Compliance to EN60950/ EN60601 BS7002 ƒ CB Certificate and report ƒ CE Mark to LVD * Note: iVS8H does not have Medical Approvals iVS Data Sheet Electrical Specifications Output 2 Adjustment range* ± 10% minimum all outputs (manual) (full module adjustment range using I C) Factory set point accuracy 1% 2 I C output program accuracy ± 5% Margining ± 4 - 6% nominal analog (single output module only) Overall regulation 0.4% or 20 mV max. (1500 W modules 1% max.) Ripple RMS: 0.1% or 10 mV, whichever is greater Pk-Pk: 1.0% or 50 mV, whichever is greater Bandwidth limited to 20 MHz Dynamic response < 2% or 100 mV, with 25% load step Recovery time To within 1% in < 300 µsec 2 Overcurrent protection** Configurable through I C (calibration required). Single output module and main output of the dual output module 105 - 120% of rated output current. Aux output of dual output module 105 - 140% of rated output current. Special programmable OCP delay on 1500 W module from 100 mSec to 25.5 seconds with shutdown features. Short-circuit protection Protected for continuous short-circuit. Recovery is automatic upon removal of short (Shutdown mode on 1500 W module). 2 Overvoltage protection* Configurable through I C Single output module: 2 - 5.5 V 122 - 134%; 6 - 60 V 110 - 120% Dual output module: 2 - 6 V 122 - 134%; 8 - 28 V 110 - 120% Triple output module: 110 - 120% of highest voltage rating 2 Thermal protection* Configurable through I C All outputs disabled when internal temp exceeds safe operating range. > 5 ms warning (AC OK signal) before shutdown Remote sense Up to 0.5 V total drop (not available on triple output module) Single wire parallel Current share to within 2% of total rated current 2 DC OK* ± 5% of nominal. Configurable through I C Minimum load Not required Housekeeping bias voltage 5 Vdc @1.0 A max. present whenever AC input is applied Overall Regulation: ± 5% Ripple and Noise: 150 mV pk-pk, Bandwidth limited to 150 MHz and measured with 10 uF Tantalum capacitor and 0.1 uF ceramic capacitor in parallel on the output. 2 Module inhibit* Configured and controlled through I C Output/Output isolation > 1 Megohm, 500 V 2 * Can be controlled via I C 2 ** Controlled via I C but requires load calibration (except 1500 W module) Environmental Specifications Operating temperature -40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 ° to 70 °C. (-20 °C start up) Storage temperature -40 °C to +85 °C Electromagnetic susceptibility Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating; non-condensing 10% to 95% RH Vibration IEC68-2-6 to the levels of IEC721-3-2 MTTF field demonstrated > 550,000 hours at full load, 220 Vac and 25 °C ambient conditions iVS Data Sheet Output Module Line-up Module Code 1 2 3 5 4 — Module Type Single Single Single Single Dual Triple Max output power 210 W 360 W 750 W 1500 W 144 W 36 W Max output current 35 A 60 A 150 A 300 A 10 A 2 A Output voltages available* 2 - 60 V 2 - 60 V 2 - 60 V 2 - 60 V 8 - 15*, 24 - 28; 8 - 15*, 8 - 15*; 8 - 15, 8 - 15, 2 - 6; 8 - 15, 8 - 15, 8 - 15*, 2 - 6; 2 - 6, 2 - 6; 24 - 28, 8 - 15; 8 - 15, 8 - 15, 18 - 28; 8 - 15, 24 - 28; 24 - 28, 2 - 6 18 - 28, 2 - 6 Standard voltage increments 25 25 25 25 16 18 Remote sense Yes Yes Yes Yes Yes Yes No Remote margin Yes Yes Yes Yes No No No 2 V-Program - I C Control Yes Yes Yes Yes Yes Yes No Active Current Share Yes Yes Yes Yes Yes No No 2 Module Inhibit - I C Control Yes Yes Yes Yes Yes Yes Yes Module Inhibit - Analog Yes Yes Yes Yes Yes No No Overvoltage/Overcurrent protection Yes Yes Yes Yes Yes Yes Yes Minimum load required No No No No No No No Slots occupied in any iVS case 1 2 3 4 1 1 * Note: Contact Factory for extended range down to 6 V Internal Part Number Reference Table Part # Where X = Description Module Code 73-558-XXXXi 0005, 0006, 0012, 0024, 0048, 04XX iVS/iMP 1500 W Module 5A0 - 5Z0 Single Dual Triple 210 W 750 W 144 W 36 W 360 W 1500 W (10 - 60 V) 1500 W with Bus Bar Adaptor Option 1500 W (2.0 - 8.0 V) (used with the 10 - 60 V module) iVS Data Sheet Output Module Voltage/Current* 2 Voltage Voltage Code Single Output Module Code Dual Output*** Triple Output I C Adjustment - - - 1 2 3 5 4 4 Ranges**** 2 V A 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 1.8 - 2.2 2.2 V B 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 2.0 - 2.4 3 V C 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 2.7 - 3.3 3.3 V D 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 3.0 - 3.6 5 V E 35 A 60 A 150 A 300 A 10 A 10 A — — 2 A 4.5 - 5.5 5.2 V F 35 A 60 A 144 A 288 A 10 A 10 A — — 2 A 4.7 - 5.7 5.5 V G 34 A 58 A 136 A 273 A 10 A 10 A — — 2 A 5.0 - 6.1 6.0 V H 23 A 42 A 97.5 A 250 A 10 A* 10 A* — — 2 A 5.4 - 6.6 8.0 V I 20 A 36 A 84.4 A 187.5 A 10 A 4 A 1 A 1 A 1 A 7.2 - 8.8 10 V J 18 A 32 A 75 A 140 A 10 A 4 A 1 A 1 A 1 A 9.0 - 11.0 11 V K 17 A 31 A 68 A 136.3 A 10 A 4 A 1 A 1 A 1 A 9.9 - 12.1 12 V L 17 A 30 A 62.5 A 125 A 10 A 4 A 1 A 1 A 1 A 10.8 - 13.2 14 V M 14 A 21 A 53.5 A 107 A 9 A 4 A 1 A 1 A 1 A 12.6 - 15.4 15 V N 14 A 20 A 50 A 100 A 8 A 4 A 1 A 1 A 1 A 13.5 - 16.5 18 V O 11 A 19 A 41.6 A 83.3 A — — — 0.5 A 0.5 A 16.2 - 19.8 20 V P 10.5 A 18 A 37.5 A 75 A — — — 0.5 A 0.5 A 18.0 - 22.0 24 V Q 8.5 A 15 A 30 A 62.5 A 4 A 2 A — 0.5 A 0.5 A 21.6 - 26.4 28 V R 6.7 A 11 A 26.8 A 53.5 A 3 A 2 A — 0.5 A 0.5 A 25.2 - 30.8 30 V S 6.5 A 11 A 25 A 50 A — — — — — 27.0 - 33.0 33 V T 6.2 A 10.9 A 22.7 A 35.8 A — — — — — 29.7 - 36.3 36 V U 5.8 A 10 A 20.8 A 35.8 A — — — — — 32.4 - 39.6 42 V V 4.2 A 7.5 A 16 A 35.7 A — — — — — 37.8 - 46.2 48 V W 4.0 A 7.5 A 15.6 A 31.2 A — — — — — 43.2 - 52.8 54 V X 3.7 A 6.0 A 13.9 A 27.7 A — — — — — 48.6 - 59.4 60 V Y 3.5 A 6.0 A 12.5 A 25 A — — — — — 54.0 - 66.0 Contact Factory Special* Z 35 A 60 A 150 A 300 A — 10 A 2.3 - 2.6 Special* Z 35 A 60 A 150 A 300 A — 10 A 3.7 - 4.4 Special* Z 20 A 36 A 80 A 140 A — 8 A 6.7 - 7.1 * Note: Contact Factory for extended range down to 6 V. *** Total output power on dual model must not exceed 144 W. ** Increments of current not shown can be achieved by paralleling modules (add currents of each **** For single output modules only. module selected). Green reference lines indicate physical module groupings Ordering Information Sample below is 3210 W case with 12 V @ 125 A; 24 V @ 8.5 A; 5 V @ 60 A; 12 V @ 10 A and 12 V @ 4 A; with no options. Module/Voltage/Option Codes First - Module Code Second - Voltage Code Case Size Case Option Codes Software Code Hardware Code Third - Option Code iVS1 - 5L1 - 1Q1 - 2EO - 4LL0 - 00 - A - ### Case Size (mm) Module Codes: First Digit Software code used Factory assembled 1-Phase Input (None) = 36 W triple O/P (1 slot) 0 - 9, A - Z Parallel code for configuration for hardware of change. “A” is firmware mods. 1 = 5” x 5” x 11”; 1500 W - 3210 W, 9 Slots 1 = 210 W single O/P (1 slot) (See parallel codes table below) standard (127 x 127 x 279.4 mm) 2 = 360 W single O/P (2 slot) Second Digit 3 = 5” x 8” x 11”; 1800 W - 4500 W, 14 Slots 3 = 750 W single O/P (3 slot) 0 = No options (127 x 203.2 x 279.4 mm) 5 = 1500 W single O/P (slot 4) 1 = Reverse air 3-Phase Input 4 = 144 W dual O/P (1 slot) 2 = Not used 6 = 5” x 5” x 11”; 3120 W, 9 Slots HUP = Extra 30mS hold-up (1 slot) 3 = Global enable (127 x 127 x 279.4) Voltage Codes: 4 = Fan Idle w/inhibit 8, 8H = 5” x 8” x 11”; 4920 W, 14 Slots See Output Module Voltage/Current table 5 = Opt 1 + Opt 3 (127 x 203.2 x 279.4 mm) Option Codes: 6 = Opt 1 + Opt 4 0 = Standard 7 = Opt 3 + Opt 4 1 = Module enable 8 = Opt 1 + 3 + 4 2 = Constant current 9 = RS485 73-544-001 3 = 1 & 2 combined B = USB 73-546-001 4 = Set for use in standard (non-intelligent case) C = 9 + 3 5 = Shutdown mode for 1500 W D = CANBUS 73-544-004 6 = 1 & 5 combined E = D + 3 Ordering Note: 7-9 Future 2 1. USB to I C module order code 73-769-001 iVS Data Sheet Ordering Information Parallel Slot No. iVS1, 6 iVS3, 8H Code Diagram Possible Configurations Diagram Possible Configurations AC 14 13 12 11 10 9 1 1 & 2 AC 9 87 6 210 210; 210 144; 144 144 210 210; 210 144; 144 144 87 65 43 21 54 32 1 2 2 & 3 AC 9 87 6 360 360; 360 210; 360 144; + above AC 14 13 12 11 10 9 360 360; 360 210; 360 144; + above 54 32 1 87 65 43 21 3 3 & 4 AC 9 87 6 750 360; 750 210; 750 144; 210 210; AC 14 13 12 11 10 9 750 750; 750 360; 750 210; 750 144; 54 32 1 210 144; 144 144 87 65 43 21 210 210; 210 144; 144 144 4 4 & 5 1500 210; 1500 144; 210 210; 210 144; 1500 1500; 1500 750; 1500 360; 1500 210; AC 9 87 6 AC 14 13 12 11 10 9 144 144; 360 210; 360 144 1500 144; 210 210; 210 144; 144 144; 360 360; 54 32 1 87 65 43 21 360 210; 360 144 5 3, 4, & 5 AC 9 87 6 750 210 210; 750 210 144; 750 144 AC 14 13 12 11 10 9 750 210 210; 750 210 144; 750 144 144 54 32 1 144 87 65 43 21 AC 9 87 6 6 iVS1,6: 4 & 6 1500 1500; 1500 750 54 32 1 AC 14 13 12 11 10 9 7 4, 5, & 6 AC 9 87 6 1500 210 210; 1500 210 144; 1500 210 210; 1500 210 144; 1500 144 144 54 32 1 1500 144 144; 1500 210 1500 87 65 43 21 AC 9 87 6 AC 14 13 12 11 10 9 8 iVS1, 6: 3 & 6 750 750 1500 1500 1500; 1500 1500 750; 1500 1500 360; 87 65 43 21 iVS3,8: 4, 5, & 9 54 32 1 1500 1500 210; 1500 1500 144 AC 9 87 6 AC 14 13 12 11 10 9 9 iVS1,6: 1 & 6 1500 1500; 1500 360; 1500 144 1500 1500 1500 360; 1500 1500 1500 210; 54 32 1 87 65 43 21 iVS3, 8: 4, 5 & 9; 12 & 13 1500 1500 1500 144 A iVS1,6: 3 & 4; 8 & 9 AC 9 87 6 750 210 & 750 210 AC 14 13 12 11 10 9 1500 1500 & 750 750 iVS3, 8: 4 & 5; 11 & 12 54 32 1 87 65 43 21 AC 9 87 6 AC 14 13 12 11 10 9 C iVS1,6: 3, 4 & 6 750, 360, 750 750 750 360 750 750 iVS3, 8: 6 & 7; 3, 4, 11 & 12 54 32 1 87 65 43 21 AC 9 87 6 AC 14 13 12 11 10 9 E iVS1,6: 3, 4, 6; 8 & 9 750, 360, 750, 210 750 750 750 750 iVS3, 8: 3, 4, 11, & 12 54 32 1 87 65 43 21 AC 9 87 6 AC 14 13 12 11 10 9 F iVS1,6: 7-8 360, 360 750 360 & 750 210; 750 750 & 750 750 54 32 1 87 65 43 21 iVS3, 8: 3 & 4; 11 & 12 AC 14 13 12 11 10 9 G iVS3, 8: 3,4 & 9 750 750 750 87 65 43 21 AC 14 13 12 11 10 9 H iVS3, 8: 11 & 12 750 750 87 65 43 21 AC 14 13 12 11 10 9 J iVS3, 8: 4 & 5; 9 & 10 1500 210 & 210 1500 87 65 43 21 AC 14 13 12 11 10 9 K iVS3, 8: 1 & 9; 5 & 12 1500 750 & 1500 750 87 65 43 21 AC 14 13 12 11 10 9 L iVS3, 8: 3 & 4; 7 & 8; 9 & 10 750 210 & 750 210 & 210 1500 87 65 43 21 AC 14 13 12 11 10 9 M iVS3, 8: 3, 4 & 9; 6 & 7 750 750 360 750 87 65 43 21 AC 14 13 12 11 10 9 N iVS3, 8: 4, 5 & 9; 12,13 & 14 1500, 1500, 1500, 210, 210 87 65 43 21 AC 14 13 12 11 10 9 P iVS3, 8: 1 & 9 1500, 750 87 65 43 21 iVS Data Sheet iVS Case Specifications iVS1 and iVS6 Input S S S S 90 - 264 Vac 170 - 264 Vac L L L L iVS1 = 5” x 5” x 11” 1500 W max. 3210 W max. O O O O (127 x 127 x 279.4 mm) T T T T 9 8 6 9 available slots 7 S S S S S iVS6 = 5” x 5” x 11” N/A 170 - 264 Vac L L L L L (127 x 127 x 279.4 mm) 3210 W max. O O O O O T T T T T 9 available slots 5 4 3 2 1 3-phase only Input iVS3, iVS8 and iVS8H 90 - 264 Vac 170 - 264 Vac iVS3 = 5” x 8” x 11” 1800 W max. 4500 W max. S S S S S S (127 x 203.2 x 279.4 mm) L L L L L L O O O O O O 14 available slots T T T T T T 14 13 12 11 10 9 90 - 264 Vac 170 - 264 Vac S S S S S S S S iVS8 = 5” x 8” x 11” 1800 W max. 4920 W max. L L L L L L L L (127 x 203.2 x 279.4 mm) O O O O O O O O 14 available slots T T T T T T T T 8 7 6 5 4 3 2 1 90 - 264 Vac 380 Vac N iVS8H = 5” x 8” x 11” 1 1800 W max. 440 Vac (127 x 203.2 x 279.4 mm) 4920 W max. 2 ~ 14 available slots 3 Figure 1. AC Input Pin Connectors Figure 1. AC Input Figure 2. Connector J1 PFC Input Connector AC Single 3 Phase (control & signals) Input Phase φ1 1 Pin Function Pin Function N 1 5 1 2 φ2 6 10 1 Input AC OK - “emitter” 2 ~ 1 AC neutral Line 1 φ3 3 2 Input AC OK - “collector” 3 2 AC line (hot) Line 2 Figure 2. Connector J1 4 3 Global DC OK - “emitter” 3 Chassis (earth) Line 3 4 Global DC OK - “collector” Mates with iVS1, iVS3 iVS6 ground Molex 90142-0010 Housing 5 Spare 4 Not used Chassis (earth) 90119-2110 Pin 6 Global inhibit/optional enable logic “0” ground 7 Global inhibit/optional enable logic “1” Connector Kit Part No.: 8 Global inhibit/optional enable return 70-841-004 9 +5 VSB housekeeping iVS8, iVS8H 10 +5 VSB housekeeping return Figure 3. Connector J2 2 I C Bus Output Connector Pin Function 10 6 1 No connection 5 1 2 No connection 3 No connection 4 Serial clock signal (SCL) Mates with 5 Serial data signal (SDA) Landwin 2050S1000 Housing 2053T011V Pin 6 Address bit 0 (A0) 7 Address bit 1 (A1) or 8 Address bit 2 (A2) JST PHDR-10VS Housing JST SPHD-002T-P0.5 (28-24) 9 Secondary return (GND) JST SPHD-001T-P0.5 (26-22) 10 5 VCC external bus (5 VCC bus) Connector Kit Part No.: 70-841-023 .33” (8 5) . .44” (11.2) 2X .32" (8.1) .63” (16.0) .32” (8.1) .63" (16.0) .59" (15.0) .32" (8.1) iVS Data Sheet Mechanical Drawings Single 210 Watt iMP Modules DC-DC Converter Output Modules V+ Control Signal Information, J1 Control Connector Pin No. Function M4X8 SCREWS 1 + Remote Sense single or dual o/p main 2 Remote Margin / V. Program single o/p V- 3 Margin High single o/p 4 - Remote Sense / Margin Low single or dual o/p main V ADJ N 1 5 Spare PIN 1 2 ~ 6 Module, Isolated Inhibit single or dual o/p DC OUTPUT CONNECTOR 3 7 Module Inhibit Return single or dual o/p 8 Current Share (SWP) single or dual o/p main 9 + Remote Sense V2 dual o/p, single is spare Single 360 Watt Figure 1. AC Input 10 - Remote Sense V2 dual o/p, single is spare V+ * Note: All iMP modules have a green DCOK LED. (except for 36 W module) M 4 X 8 SCREWS WITH CONICAL Figure 4. Connector J1 WASHER V- Mates with PIN 1 5 1 Molex 90142-0010 Housing 6 10 90119-2110 Pin V ADJ Figure 2. Connector J1 DC OUTPUT CONNECTOR Single 750 Watt Single 1500 Watt 2-8 V Single 1500 Watt 10-60 V V+ 59.3 ± 0.2 (3x) 31.6 ±0.8 03/24/2008 11.3 ±0.8 8.1 ±0.8 (2x) 15.0 ±0.8 DC OUTPUT CONNECTOR (2x) 16.0 ±0.2 PIN 1 (2x) 16.0 ±0.2 For Factory-Use Only M4X8 SCREWS W/ CONICAL WASHER (6X) VADJ V- M4X8 SCREWS V ADJ PIN 1 (4X) DC OUTPUT V- CONNECTOR V+ Dual 144 Watt Triple 36 Watt V1 + .46 (11.7) (4X) V1 + V1 - V1 - V2 + V2 + V2 - V2 - V3 + .30 (7.5)(3X) V3 - M3X8 SCREWS WITH SPRING WASHER (4X) 1.17 (29.7) V2 ADJ Mates with .42 (10.7) Molex 09-91-0600 Housing 26-60-5060 Pin V1 ADJ .32 (8.1) PIN 1 1.24"(31.5) .61"(15.6) (2X) (2X) .44" (11.0) .48" (12.1) .44" (11.4) .48” (12.1) 1.38” (35.2) (2X) (2X) .44” (11.4) 1.38" (35.1) iVS Data Sheet iVS Series 5-Inch Case Size: iVS1: 5” x 5” x 11” (127 mm x 127 mm x 279.4 mm) iVS1 (1500/3210 Watts Max) Weight: iVS1 Case: 6.2 lbs. • 1500 W Single: 2.0 lbs. • 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. • 144 W Dual: 0.6 lb. REVERSE AIRFLOW DIRECTION NORMAL AIRFLOW DIRECTION 127.0 ± 0.5 B B A 127.0 ± 0.5 279.40 ± 1.27 63.5 AC INPUT AC INPUT AC INPUT CONNECTOR CONNECTOR CONNECTOR FAN L 92 X 92 X 38 mm N PE 127.0 ± 0.9 127.0 ± 0.9 101.6 ± 0.9 USB PROGRAMMING CONNECTOR OPTION 65.5 SELV CONTROL CONNECTOR 2 I C C C C 12.7 11.6 CONNECTOR DC OK AC OK LED LED 171.5 OUTPUT MODULE 19.1 M4 MTG HOLES 4 PL 13.5 12.0 AREA 33.5 57.4 “MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES” 171.45 29.05 5.00 12.70 B 114.30 A 171.45 19.05 22.80 Notes: 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m). iVS Data Sheet iVS Series 8-Inch Case Size: iVS3: 5” x 8” x 11” (127 mm x 203.2 mm x 279.4 mm) iVS3 (1800/4500 Watts Max) Weight: iVS3 Case: 9.0 lbs. • 1500 W Single 2.0 lbs.• 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. •144 W Dual: 0.6 lb. REVERSE AIRFLOW DIRECTION B NORMAL AIRFLOW DIRECTION 203.2±0.5 B 98 A 279.4±1.27 A 52.6 FAN AC INPUT 80 X 80 X 38mm CONNECTOR USB PROGRAMMING CONNECTOR OPTION OUTPUT MODULE AREA SELV CONTROL CONNECTOR C C C 2 I C 42 DC OK LED AC OK LED 171.45 M4 MTG HOLES 4 PL A 61.2 19.1 81.5 “MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES #8-32 MTG HOLES 5PL MARKED “A” B 29.1 171.5 6, 7 REF BA B A B A B A BA 16.2 M4 MTG A 19.1 171.5 HOLES 5 PL MARKED “B” Notes: 1. Input: Barrier type. Three M4 screws (0.512” centers). Max torque: 7 in-lbs. (0.79 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m). SLOT 14 SLOT 13 SLOT 12 SLOT 11 SLOT 8 SLOT 10 SLOT 7 SLOT 9 SLOT 6 SLOT 5 SLOT 4 SLOT 3 SLOT 2 SLOT 1 127±0.9 101.6 ± 0.9 12.7 11.6 173.3 149.4 14.4 12.7 177.8 65.5 L3 L2 INTERNAL FUSES 15A/250V L1 iVS Data Sheet iVS Series 5-Inch Case Size: iVS6: 5” x 5” x 11” (127 mm x 127 mm x 279.4 mm) iVS6 (3210 Watts Max) Weight: iVS6 Case: 6.0 lbs. • 1500 W Single 2.0 lbs. • 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. • 144 W Dual: 0.6 lb. 279.4±1.0 5.0±0.5 NORMAL AIRFLOW DIRECTION REVERSE AIRFLOW DIRECTION 293.0±1.2 GND 20.3±0.6 127.0±0.5 AC INPUT CONNECTOR 63.5 L1 L2 L3 USB PROGRAMMING CONNECTOR AC OK 2 I C CONNEC- LED FOR M4 SCREW (4X) SELV CONTROL 19.1 (2X) 171.5 (2X) DC OK FOR M4 SCREW (4X) (FOR SYSTEM MOUNTING) CONNECTOR 13.5 LED 171.5 (2X) (FOR SYSTEM MOUNTING) 19.1 (2X) 33.5 12.0 57.4 19.1 (2X) 171.5 (2X) FOR #8-32 SCREW (4X) (SYSTEM MOUNTING) FOR M4 SCREW (4X) (FOR SYSTEM MOUNTING) 171.5 (2X) 29.1 (2X) Notes: 1. Input: Barrier type. Four M3 screws (0.325” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m). 11.6 65.5 (2X) 12.7 (4X) 12.7 (4X) 12.7 (2X) 12.7 (2X) SLOT 5 SLOT 9 SLOT 4 SLOT 8 SLOT 3 SLOT 7 SLOT 2 SLOT 6 SLOT 1 127.0±0.9 101.6±0.9 (2X) 12.6±0.6 101.6±0.9 (2X) iVS Data Sheet iVS Series 8-Inch Case Size: iVS8: 5” x 8” x 11” (127 mm x 203.2 mm x 279.4 mm) iVS8 (4920 Watts Max) iVS8H (4920 Watts Max) Weight: iVS8 Case: 9.0 lbs. • 1500 W Single 2.0 lbs. • 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. • 144 W Dual: 0.6 lb. 6.8 max (2x) NORMAL AIRFLOW DIRECTION REVERSE AIRFLOW DIRECTION 203.2±0.2 291.1±1.2 155.6 AC Input 279.4±0.2 Connector 52.6 GND Terminal USB Programming Connector Option 19.1 (2x) 19.1 (2x) 171.5 (2x) MOSYTEM Mounting MOSYTEM Mounting MOSYTEM Mounting 171.5 (2x) for M4 Scr for M4 Scr for M4 Screw (I3X) (’a’) ew (I3X) (’a’) ew (I3X) (’a’) I2C Connector SELV Control 31.8 7 Connector 50.7 171.5 (2x) 72.1 19.1 (3x) 29.1 (3x) MOSYTEM Mounting for 171.5 (2x) #8-32 Screw (5X) (’a’) Notes: 1. Input: Barrier type. Three M3.5 screws (0.394” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8 mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8 mm screws. Max. torque: 5 in-lbs. (0.57 N-m). 11.6 (2x) 65.5 (2x) 127.0±0.2 127.0±0.2 12.7 (2x) 12.7 (2x) 12.7 (2x) 14.4 (2x) 12.7 (2x) 15.5 (2x) 101.6±0.9 23.9 (2x) 101.6±0.9 12.7 (2x) iVS Data Sheet Optional CANBUS or RS485 Interface 2 The RS485/CAN-to-I C uses 2 Input Protocols and 1 Slave/Server Device(s) Output Protocol. The Input Protocols used are RS485 using Modbus Adapter (Command Index: 0x01), and CAN using modified Modus (Command Index: 0x02). Output Protocols 2 I C with SMBus 2 The Output Protocol use is: I C with SMBus support Support (Command Index: 0x80). Adapter Protocol Adapter Command Adapter Controls Input Protocols RS485 using CAN using Modbus Modied Modbus Master/Client Device(s) 2 RS485/CAN - to - I C For detailed info, download the Software Requirements Specification (SRS) from http://www.artesyn.com/ power/power-supplies/category.php?catID=103 2 iVS CAN RS485 iVS I C USB WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Waterfront Business Park 14/F, Lu Plaza Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street USA West Midlands, DY5 1LX Kwun Tong, Kowloon +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. Specifications are subject to change without notice. © 2018 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. iVS DS 26Mar2018