POWER LCM600 Data Sheet 600 Watt Bulk Front End Total Power: 600 W # of Outputs: Single Outputs: 12 to 60 V Optional 5.0 V standby SPECIAL FEATURES ƒ 600 W output power ƒ Low cost ƒ 2.4” x 4.5” x 7.5” ƒ 7.41 W/cu-in Electrical Specifications ƒ Industrial/Medical safety Input ƒ -40 °C to 70 °C with derating Input ra nge 85 - 264 Vac (Operating) ƒ Optional 5 V @ 2 A housekeeping 115/230 Vac (Nominal) Input through standard IEC connector/ TERMINAL BLOCK ƒ High efficiency: 89% typical Frequency 47 - 440 Hz, Nominal 50/60 ƒ Variable speed “Smart Fans” ƒ DSP controlled front end Input fusing Internal 10 A fuses, both lines fused ƒ Conformal coat option Inrush current ≤ 25 A peak, either hot or cold start ƒ ± 20% adjustment range Power factor 0.99 typical, meets EN61000-3-2 ƒ Margin programming Harmonics Meets IEC 1000-3-2 requirements ƒ OR-ing FET Input current 8 A RMS max input current, at 100 Vac ƒ Terminal block input option Hold up time 20 ms minimum for main O/P, at full rated load Efficiency > 89% at full load COMPLIANCE Leakage current < 300 μA @ 240 Vac ƒ EMI Class B ON/OFF power switch N/A ƒ EN61000 Immunity Power line transient MOV directly after the fuse Isolation Isolation: PRI-Chassis 2500 Vdc Basic SAFETY PRI-SEC 4000 Vac Reinforced 2xMOPP ƒ UL/CSA UL60950-1/CSA C22.2 SEC-Chassis 500 Vdc No. 60950-1 ES60601-1/CSA C22.2 LCM600Q Efciency Without the 5 Vsb No. 60601-1 92.00 ƒ TUV EN60950-1 90.00 EN60601-1 88.00 ƒ CB Report IEC60950-1 86.00 IEC60601-1 100 Vac 84.00 ƒ CCC GB4943, GB9254 230 Vac and GB17625 82.00 80.00 78.00 76.00 25 50 75 100 Loading % Efciency % LCM600 Data Sheet Electrical Specifications Output Output rating See ordering information table 85 - 264 Vac Set point ± 0.5% 85 - 264 Vac Total regulation range Main output ± 2% Combined line/load/transient when measured at output 5 Vsb ± 1% terminal Rated load 600 W maximum Derate linear to 50% from 50 °C to 70 °C Minimum load Main output @ 0.0 A No loss of regulation 5 Vsb @ 0.0 A Output noise (PARD) 1% max p-p Main output 50 mV max p-p 5 Vsb output Measured with a 0.1 μF Ceramic and 10 μF Tantalum Capacitor on any output, 20 MHz Output voltage overshoot No overshoot/undershoot outside the regulation band during on or off cycle Transient response < 300 µSec 50% load step @ 1 A/µs Step load valid between 10% to 100% of output rating Recovery time to within 1% of set point at onset of transient Max units in parallel Up to 10 Short circuit protection Protected, no damage to occur Bounce mode Remote sense Compensation up to 500 mV Output isolation Standard per safety requirements Forced load sharing To within 10% of all shared outputs Analog sharing control Overload protection (OCP) 105% to 125% Main output 120% to 170% 5 Vsb output Overvoltage protection (OVP) 125% to 145% 12 V output 110% to 125% 5 Vsb output Overtemp protection 10 - 15 °C above safe operating area Both PFC and output converter monitored Fan Fault Protection For-N option only. Will shutdown output and DC_OK Environmental Specifications Operating temperature -40 °C to +70 °C, linear derating to 50% from 50 °C to 70 °C Storage temperature -40 °C to +85 °C Humidity 10 to 90%, non-condensing. Operating. Conformal coat option available. Fan noise < 45 dBA, 80% load at 30 °C “-N” Low Noise Option < 35 dBA, 80% Load at 30 °C Altitude Operating - 16,404.2 feet Storage - 30,000 feet Shock MIL-STD-810F 516.5, Procedure I, VI. Storage Vibration MIL-STD-810F 514.5, Cat. 4, 10. Storage Ordering Information Current Model Nominal Output Set Point Output Ripple Max Continuous Combined Line/ Number* Output Voltage Set Point Tolerance Adjustment Range Min Max P/P (0-50 ˚C) Power Load Regulation LCM600L 12 V 12 V ±0.5% 9.6 - 14.4 V 0 A 52 A 120 mV 600 W 2% LCM600N 15 V 15 V ±0.5% 12.0 - 19.5 V 0 A 44 A 150 mV 600 W 2% LCM600Q 24 V 24 V ±0.5% 19.2 - 28.8 V 0 A 27 A 240 mV 600 W 2% LCM600U 36 V 36 V ±0.5% 28.8 - 43.2 V 0 A 16.7 A 240 mV 600 W 2% LCM600W 48 V 48 V ±0.5% 38.4 - 57.6 V 0 A 14 A 280 mV 600 W 2% *Note: Add “-T” for terminal block instead of IEC input Add “-N” for low noise model on 12 V or 24 V models Add “-4” for 5 V Standby output Add “-A” will be automatically added to all orders to denote new Aesthetics style chassis unless otherwise specified Add “-8” for models with special Constant Current Mode operation Example: a 24 V with terminal block, low noise and standby with new Aesthetics would be LCM600Q-T-N-4-A LCM600 Data Sheet Pin Assignment Signals Name Description Pin Number(s) +Vout Power rail SK4 GND Power GND SK5 Signals Name Description SK2 Pin Number A2 EEPROM Address 1 -VPROG Return connection of external supply for Margin Programming 2 A1 EEPROM Address 3 -Vsense Remote Sense Return 4 ISHARE Load share voltage 5 A0 EEPROM Address 6 SDA1 Serial Data Signal (I2C) 7 +VPROG Positive connection of external supply for Margin Programming 8 SCL1 Serial Clock Signal (I2C) 9 +Vsense Remote Sense Positive 10 5VSB 5V standby 11 GND 5V standby Return 12 5VSB 5V standby 13 G_DCOK_C Global DCOK Collector 14 GPIOA6 EEPROM Write Protect 15 G_DCOK_E Global DCOK Emitter (GND) 16 GND Return Ground for output signal and I2C communication 17 G_ACOK_C Global ACOK Collector 18 INH_EN Turn Off Main Output 19 G_ACOK_E Global ACOK Emitter (GND) 20 Note: Mating connector for SK2 is: LANDWIN: PN 2050S2000 Housing and PN 2053T021V Contact CIVILUX: PN CI0120SD000 Housing and PN CI01TD21PE0 Contact JST: PN PHDR-20VS housing and PN: SPHD-001T-P0.5 Signal Output Signal Connectors (SK2) SK2 Mating Connector: JST Part Number PHDR-20VS; Contact Pins: JST Part Number SPHD-001T-P0.5 LED INDICATORS Two (2) provided are clearly visible up to a 45 degree offset from vertical with office environment ambient lighting. The status is reflected in the indicator color. The DC_OK LED LED is bicolor. It shall light green if the DC output is within specification, and amber if the output falls out of specification. The AC_OK LED LED is green if the AC is within specification and off when out of specification. Note: With 5 V standby, Amber also indicates that PSU is in standby mode/output off. CONTROL SIGNALS AC_OK Open collector 0.5 V maximum at 10 mA. Both emitter and collector access provided. DC_OK Open collector 0.5 V maximum at 10 mA. Both emitter and collector access provided. DC_OK will de-assert when output is loss due to OCP, OVP, OTP, or Fan Fault (for -N option). PS_INHIBIT/ENABLE Signal 0.0 - 0.5 V contact closure, output OFF LCM600 Data Sheet Ordering Information LCMXXXXY - A - B - C - ### Case Size Input Termination Acoustic Noise Option Codes Hardware Code 1-Phase input where XXXX = Factory Assigned for 600 = 2.4” x 4.5” x 7.5”, 600 W Blank = IEC connector Blank = Standard Blank = No Options Modiefied standards T = Terminal Block N = Low Noise Fan 1 = Conformal Coat Voltage Code Y = 4 = 5 V Standby Code 5 = Opt 1 + 4 L 12 N 15 Q 24 U 36 W 48 Mechanical Drawings New Mechanical Reference Drawing: (212.2 ref) 190.5 0.5 SEE DETAIL A (18.5) Weight: 2.84 lbs (1.29 Kg) SEE DETAIL C (TRIMPOT LOCATION) MOUNTING LOCATIONS SCREW PENETRATION DEPTH IS 4.6 mm MAX. GROUND RECOMMENDED SCREW TORQUE: M3.5 x 0.6P = 6 - 8kgf-cm NEUTRAL M4.0 x 0.7P = 8 - 10kgf-cm LIVE Note 7 RECOMMENDED SCREW TORQUE: M3.5x0.6P = 6-8kgf-cm M4.0x0.7P = 8-10kfg-cm DETAIL A SCALE 1.500 Note 8 INPUT: TERMINAL BLOCK TYPE. M3.5 SCREW TORQUE VALUE OF 12kgf-cm SCREW-MC PHILIP PAN USING WIRE GAUGE 22-19 (9.5mm CENTERS) WITH WASHER M4x8 (8X) MOUNTING LOCATIONS BOTH SIDES M4X0.7P THREAD BRAND LOGO SEE DETAIL B INPUT TERMINAL BLOCK SEE NOTE 7 SEE NOTE 8 (2X)6 0.5 (2X)10.6 50 LED (AC OK) SK4 & SK5 (2X)182.5 0.5 LED (DC/OK FAIL) SK2 SIGNAL (2X)177.5 0.5 CONNECTOR - 20WAY (2X)10 0.5 VOLTAGE ADJUSTMENT: CLOCKWISE - INCREASE VOLTAGE COUNTER CLOCKWISE - DECREASE VOLTAGE DETAIL C (TRIMPOT LOCATION) (4X) MOUNTING LOCATIONS M4X0.7P THREAD SEE NOTE 7 DETAIL B AC INLET VERSION Airflow direction NOTE: OPTIONAL BARRIER STRIP OUTPUT TERMINAL AVAILABLE OPTIONAL MOLEX TYPE CONNECTOR OUTPUT AVAILABLE 114.3 0.5 9.5 62 1 (2X)47 0.5 9.5 (2X) 94.45 0.5 41 16.8 (2X)22 0.5 17.65 0.5 11.150.5 50 LCM600 Data Sheet Mechanical Drawings – Terminal Block Input Old Mechanical Reference Drawing: Weight: 2.84 lbs (1.29 Kg) 190,5 0,5 SEE DETAIL A 18,5 REF Note 7 - RECOMMENDED SCREW TORQUE: SEE DETAIL B (TRIMPOT LOCATION) M3.5x0.6P = 6-8kgf-cm M4.0x0.7P = 8-10kfg-cm GROUND NUETRAL LIVE DETAIL A SCALE 8:5 SCREW-MC PHILIP PAN INPUT TERMINAL BLOCK WITH EXT-T WASHER PRODUCT LABEL PROVISION FOR FUTURE SEE NOTE 8 M3.5 x P0.6 x 6 LABEL REQUIREMENTS (8X) MOUNTING LOCATIONS BOTH SIDES M4X0.7P THREAD SEE NOTE 7 LED (DC/OK FAIL) LED (AC OK) POS - SK4 (2X)6 0,5 (2X)10,6 50 NEG - SK5 (2X)182,5 0,5 SK2 SIGNAL CONNECTOR - 20WAY (2X)177,5 0,5 (2X)10 0,5 VOLTAGE ADJUSTMENT: (4X) MOUNTING LOCATIONS CLOCKWISE - INCREASE VOLTAGE M4X0.7P THREAD COUNTER CLOCKWISE - DECREASE VOLTAGE SEE NOTE 7 DETAIL B (TRIMPOT LOCATION) Airflow direction 61 0,5 (2X)47 0,5 114,3 0,5 40,2 (2X)94,45 0,5 (2X)22 0,5 32,8 12,8 9,5 9,5 16,8 17,65 0,5 15,75 11,1 5 0,5 LCM600 Data Sheet Low Noise vs. Non-Low Noise LCM600 Model 60.0 25 Deg Ambient NON-Low noise version 58.0 56.0 Low noise version 54.0 52.0 50.0 48.0 46.0 44.0 42.0 40.0 38.0 36.0 34.0 32.0 30.0 02.5 57.5 10 12.5 15 17.5 20 22.5 25 27.5 30 32.5 35 37.5 40 42.5 45 47.5 50 LOAD (A) 60.0 58.0 50 Deg Ambient 56.0 54.0 52.0 50.0 48.0 46.0 44.0 42.0 NON-Low noise version 40.0 38.0 Low noise version 36.0 34.0 32.0 30.0 02.5 57.5 10 12.51517.52022.52527.53032.535 37.54042.54547.550 LOAD (A) NON-Low noise version Low noise version 25 ˚C ambient 50 ˚C ambient 25 ˚C ambient 50 ˚C ambient Fan (V) RPM Noise (dbA) Fan (V) RPM Noise (dbA) LOAD (A) RPM Noise (dbA) LOAD (A) RPM Noise (dbA) LOAD (A) PWM 0 6.254 3558.0 40.9 6.228 3460.9 39.9 0% 0 3028 35.2 0 3180 36.0 2.5 6.257 3559.8 41.0 6.228 3460.9 39.9 5% 2.5 3028 35.2 2.5 3300 36.7 5 6.262 3562.0 41.0 6.230 3494.3 40.1 10% 5 3028 35.2 5 3300 36.7 7.5 6.263 3562.0 41.0 6.242 3526.6 40.1 15% 7.5 3060 35.4 7.5 3360 37.0 10 6.242 3528.9 40.5 6.242 3526.6 40.1 20% 10 3028 35.2 10 3360 37.0 12.5 6.251 3530.9 40.6 6.237 3515.6 40.4 25% 12.5 3028 35.2 12.5 3360 37.0 15 6.251 3538.3 40.7 6.229 3504.9 40.2 30% 15 3060 35.4 15 3360 37.0 17.5 6.226 3538.2 40.7 6.205 3482.8 39.4 35% 17.5 3060 35.4 17.5 3388 37.2 20 6.223 3541.0 40.7 6.217 3490.1 40.0 40% 20 3028 35.2 20 3388 37.2 22.5 6.242 3545.1 40.8 6.227 3493.8 40.1 45% 22.5 3028 35.2 22.5 3540 38.0 25 6.253 3553.9 40.9 6.234 3504.3 40.2 50% 25 3060 35.4 25 3840 39.2 27.5 6.254 3564.1 41.0 6.212 3501.7 40.2 55% 27.5 3028 35.2 27.5 4104 40.2 30 6.253 3552.2 40.9 6.642 3787.4 44.1 60% 30 3028 35.2 30 4408 41.4 32.5 6.264 3559.7 41.0 7.893 4652.3 48.0 65% 32.5 3060 35.4 32.5 4736 42.7 35 6.262 3559.6 41.0 9.153 5463.4 50.0 70% 35 3060 35.4 35 5184 44.5 37.5 6.262 3560.8 41.0 11.035 6600.2 52.0 75% 37.5 3060 35.4 37.5 5728 46.4 40 6.262 3559.8 41.0 11.605 6993.9 53.2 80% 40 3060 35.4 40 6688 49.5 42.5 7.637 4521.2 47.8 11.608 6997.2 53.2 85% 42.5 3420 37.4 42.5 7560 51.8 45 8.919 5362.2 49.3 11.608 6997.2 53.2 90% 45 3868 39.3 45 7584 51.9 47.5 10.068 6139.5 51.0 11.608 6997.2 53.2 95% 47.5 4376 41.3 47.5 7584 51.9 50 11.362 6893.4 52.8 11.608 6997.2 53.2 100% 50 5040 43.9 50 7584 51.9 NOISE (dBA NOISE (dBA LCM600 Data Sheet Accessories PIN 20 PIN 19 PIN 3 PIN 2 PIN 1 300 ± 5 mm Order kit part number 73-788-001 for control connector interface with .3m wires attached PIN 19 PIN 20 PIN 3 PIN 2 PIN 1 Order kit part number 73-788-002 for control connector interface with unloaded housing and 20 pins Miscellaneous Specifications BURN-IN 100% Burn-in at 45 °C, at 80 - 90 % load. Duration of burn-in determined by Quality Assurance Procedures. MTBF The power supply has a minimum MTBF of 300K hours using the Bell core 332, issue 6 specification @ 25 °C and 40 °C, ambient, at full load. With the power supply installed in a system in a 25 °C ambient environment and operating at full load, capacitor life shall be 10 years, minimum for ALL electrolytic capacitors contained within this power supply. The power supply shall demonstrate a MTBF level of > 500,000 hours. QUALITY ASSURANCE Full QAV testing shall be conducted in accordance with Artesyn Embedded Technologies Standards with reports available upon request. WARRANTY Artesyn Embedded Technologies shall warrant the power supply to be free of defects in materials and workmanship for a minimum period of three years from the date of shipment, when operated within specifications. The warranty shall be fully transferable to the end owner of the equipment powered by the supply. WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Waterfront Business Park 14/F, Lu Plaza Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street USA West Midlands, DY5 1LX Kwun Tong, Kowloon +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. Specifications are subject to change without notice. © 2017 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. LCM600 DS 17May2017