POWER LPQ350 Series Data Sheet 350 Watts Total Power: 350 Watts Input Voltage: 85-264 Vac 120 - 300 Vdc # of Outputs: Quad Special FeatureS ƒ Active power factor correction ƒ IEC EN61000-3-2 compliance ƒ Remote sense on 1st and 4th output ƒ Power fail and remote inhibit ƒ Single wire current sharing Electrical Specifications ƒ Built-in EMI filter Input ƒ Adjustable floating 4th output Input range 85-264 VAC; 120-300 VDC ƒ 2 Supervisory output 5 V and 12 V Frequency 47-440 Hz ƒ Overvoltage protection Inrush current 38 A max, cold start @ 25 °C ƒ Overload protection Efficiency 75% typical at full load ƒ Thermal overload protection EMI filter FCC Class B conducted and radiated ƒ DC power good CISPR 22 Class B conducted and radiated ƒ 135 khz switching frequency EN55022 Class B conducted and radiated ƒ Cover -C VDE 0878 PT3 Class B conducted and radiated ƒ Optional with fan cover -CF Power factor 0.99 typical ƒ Optional end-mounted fan -CEF Safety ground leakage current 0.5 mA @ 50/60 Hz, 264 VAC input Output SaFety Maximum power With cover: 350 W with 30 CFM forced air, (-C) (-CF) (-CEF) ƒ VDE 60950 Adjustment range ± 5% min. on main: 3.3-24 V on output 4 21310-3336-0001 Supervisory output 5 V @ 500 mA regulated, 12 @ 150 mA x2 ƒ UL 60950 Hold-up time 20 ms @ 350 W load, 115 VAC nominal line ƒ CSA CSA 22.2-234 Level 5 LR109492C Overload protection Short circuit protection on all outputs. Case overload protected ƒ NEMKO EN 60950/EMKO-TUE @ 110-145% above peak rating P97102061 (74-sec) 203 Overvoltage protection 5 V output: 5.7 - 6.7 VDC ƒ BABT EN60950/BS7002 607019 ƒ CB Certificate and report 4048, 4049 ƒ CE Mark (LVD) LPQ350 Series Data Sheet Logic Control Power fail TTL logic signal goes high 50 - 150 msec after 5 V output. It goes low at least 4 msec before loss of regulation Remote on/off Requires an external contact (N.O or N.C) to inhibit outputs DC-OK TTL logic goes high 50 - 150 msec after 5 V output. It goes low when there is loss of regulation Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected Environmental Specifications Operating temperature 0° to 50 °C ambient; derate each output at 2.5% per degree from 50° to 70 °C Storage temperature -40 °C to +85 °C Temperature coefficient ± 0.4% per °C Electromagnetic susceptibility Designed to meet IEC 801, -2, -3, -4, -5, -6, Level 3 Humidity Operating; non-condensing 5% to 95% Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.7 G peak 5Hz to 500Hz, operational MTBF demonstrated > 550,000 hours at full load and 25 °C ambient conditions Ordering Information 1 2 3 Model Number Output Voltaqe Minlmun Load Maximum Load Peak Load Requlation Ripple P/P(PARD) LPQ352-C +5 V 5 A 50 A 60 A ±2% 50 mV +12 V 0 A 12 A 14 A ±3% 120 mV -12 V 0 A 6 A 8 A ±3% 120 mV 3.3 - 24 V *1 A 6 A 8 A ±3% 240 mV max. 1 LPQ353-C +5 V 5 A 50 A 60 A ±2% 50 mV +15 V 0 A 12 A 14 A ±3% 150 mV -15 V 0 A 6 A 8 A ±3% 150 mV 3.3 - 24 V *1 A 6 A 8 A ±3% 240 mV max. 1 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. 2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 μF in parallel with a 0.1 μF capacitor at rated line voltage and load ranges. 4. 4th output 3.3 - 24 V factory set at 5 V. 5. * Minimum load required when the output is set below 5 volts. 6. If optional CF or CEF fans are not used, 30CFM forced air cooling needs to be provided and is required through the length of the power supply. Not convection rated. 7. Remote inhibit resets OVP latch Note: -CF suffix added to the model number indicates cover with fan, -CEF suffix added to model number indicates end-mounted fan chassis. LPQ350 Series Data Sheet Mechanical Drawing Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance ± .02”. 3. Specifications are at factory settings 4. To enable normally closed Remote Inhibit, cut Jumper J1. 5. Mounting maximum insertion depth is 0.12”. 6. Warranty: 2 year 7. Weight: 4 lb./1.8kg. LPQ350 Series Data Sheet Pin Assignments SK1 PIN 1 Neutral PIN 2 Line PIN 3 Ground SK2 PIN 1 + 12/15V PIN 2 Common PIN 3 Common PIN 4 - 12/15 V PIN 5 3.3-25 V RET Float PIN 6 3.3-25 V Float SK3 PIN 1 + Sense V 4 PIN 2 - Sense V 4 PIN 3 +Sense V 1 PIN 4 -Sense V 1 PIN 5 POK PIN 6 C.Share PIN 7 DC-OK PIN 8 Inhibit (N.O.) PIN 9 Inhibit (N.C.) PIN 10 COM SK4 PIN 1 + Fan 1 (12V@150mA) PIN 2 – Common SK5 PIN 1 + 5V aux (5V@100mA) PIN 2 – Common SK6 PIN 1 + Fan 2 (12V@150mA) PIN 2 – Common Mating Connectors SK3 Molex: 51191-1000 PINS: 50802-9101 SK4 Molex: 22-01-3027 PINS: 08-50-0114 SK5 Molex: 22-01-3027 PINS: 08-50-0114 SK6 Molex: 22-01-3027 PINS: 08-50-0114 Astec Connector Kit #70-841-011, includes all of the above. WORLDWIDE OFFICES americas europe (uK) asia (HK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street Kwun Tong, Kowloon USA West Midlands, DY5 1LX +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of For support: productsupport.ep@artesyn.com this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. LPQ350 Series-DS 07.25.14 © 2014 Artesyn Embedded Technologies, Inc.