POWER LPS100-M Series Data Sheet 150 Watts Total Power: 80 - 150 Watts Input Voltage: 90 - 264 Vac 120 - 300 Vdc # of Outputs: Single SPECIAL FEATURES ƒ Medical and ITE safety approvals, 2X MOPP ƒ Active power factor correction ƒ 2” x 4” footprint ƒ Less than 1U high ƒ EN61000-3-2 compliant ƒ Remote sense ƒ Power fail Electrical Specifications ƒ Adjustable main output Input ƒ Built-in Class B EMI filter ƒ Overvoltage protectionInput ra nge 90 - 264 Vac; 120 - 300 Vdc ƒ Overload protection Frequency 47 - 63 Hz ƒ Thermal overload protection Inrush current 50 A max., cold start @ 25 °C ƒ Isolated 12 V fan output Efficiency 88% typical at full load ƒ LPX100 Enclosure kit available EMI/RFI FCC Class B conducted; CISPR22 Class B conducted; ƒ POE isolation on main output of EN55022 Class B conducted; VDE0878PT3 Class B conducted LPS109-M Safety ground leakage 275 μA @ 50/60 Hz, 264 Vac input current SAFETY Output ƒ TUV 60950, 60601-1 Maximum power 100 W for convection (80 W for LPS102-M); ƒ UL 60950, 60601-1 150 W with 30 CFM forced air (120 W for LPS102-M) ƒ cULus 60950, 60601-1 Adjustment range ± 10% minimum on the main outputs ƒ CB Certificate & report Fan output 12 V @ 1 A isolated, ± 10% ƒ CE Mark (LVD) Hold-up time 10 ms @ 150 W load, 120 Vac input ƒ CQC Mark Overload protection Short circuit protection on all outputs. Case overload protected @ 110-160% above rating Overvoltage protection 15-35% above nominal output Logical Control Power failure Open collector logic signal goes high 100-500 msec after main output; it goes low at least 6 msec before loss of regulation Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. LPS100-M Series Data Sheet Environmental Specifications 5 Operating temperature 0° to 50 °C ambient derate each output as 2.5% per degree from 50° to 70 °C. (-20 °C startup ) Storage temperature -40 °C to +85 °C Electromagnetic susceptibility Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating; non-condensing 10% to 95% RH Vibration IEC 60068-2-6 to the levels of IEC721-3-2 MTBF calculated 534,000 hours at full load and 25 °C ambient conditions, 230 V input, Bellcore Ordering Information Ripple Minimum Maximum Load with Maximum Load with 2 Model Number Output Voltage Peak Load Regulation 3 Load Convection Cooling 30CFM Forced Air P/P (PARD) LPS102-M 5 V 0 A 16 A 24 A 30 A ± 2% 50 mV LPS103-M 12 V 0 A 8.3 A 12.5 A 14 A ± 2% 120 mV LPS104-M 15 V 0 A 6.7 A 10 A 11 A ± 2% 150 mV LPS105-M 24 V 0 A 4.2A 6.3 A 7 A ± 2% 240 mV LPS108-M 48 V 0 A 2.1 A 3.1 A 3.5 A ± 2% 480 mV LPS109-M 54 V 0 A 1.85 A 2.8 A 3.1 A ± 2% 540 mV 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. 2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 4. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. 5. At 115 Vac input. Pin AssignmentsMating Connectors Connector LPS100-M Molex P/N: 09-50-3031, Pins: 08-52-0072 or AC Input (SK1) Landwin P/N: 3060S0302, Pins: 3360T011P SK1 Pin 1 Neutral AC Ground Molex: 01-90020001 Pin 3 Line Molex P/N: 09-50-3081, Pins: 08-52-0072or DC Output SK2 Pin 1 Common Landwin P/N: 3060S0802, Pins: 3360T011P (SK2) Pin 2 Common Molex P/N: 35155-0400, Pins: 08-70-0056 or Remote Sense Pin 3 Common (SK203) Landwin P/N: 2640S04A0, Pins: 2543T011P Pin 4 Common Molex P/N: 22-01-1042, Pins: 08-70-0049 or Fan: (SK5) Pin 5 +Vout Landwin: P/N: 2510S04A0, Pins: 2543T011P Pin 6 +Vout Artesyn Embedded Technologies Connector Kit #70-841-025, Pin 7 +Vout includes all of the above Pin 8 +Vout Notes: 1. Specifications subject to change without notice. SK203 Pin 1 Common 2. All dimensions in inches (mm), tolerance is ±.02”. Pin 2 Power Fail 3. Mounting holes M1, M2 should be grounded for EMI purpose Pin 3 - Remote Sense 4. Mounting M1 is safety ground connection Pin 4 + Remote Sense 5. Specifications are for convection rating at factory settings at 115 Vac input 25 °C unless otherwise stated. SK5 Pin 1 +12 V Fan 6. This power supply requires mounting on metal standoffs 0.20” Pin 2 +12 V Fan (5 m) in height. Pin 3 Fan Return (Isolated) 7. For DC input an external DC safety rated fuse must be used. Pin 4 Fan Return (Isolated) 8. Warranty: 2 years 9. Weight: 0.44 lb. / 0.20 kg LPS100-M Series Data Sheet Mechanical Drawing VR1 Output Voltage SK20 3 Adjust Pot M2 M1 1 4 SK2 8 GND 1 4 SK5 1 SK1 1 3 3.72" Mounting Hole (94.6) Ø0.16"[4.0] 4 Places Max. Screw Head 4.00" Diameter .22” (5.6) (101.6) 0.197” (5.0) Minimum Standoff height WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Waterfront Business Park 14/F, Lu Plaza Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street USA West Midlands, DY5 1LX Kwun Tong, Kowloon +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. Specifications are subject to change without notice. © 2017 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. LPS100-M DS 08Dec2017 2.00" (50.8) (2.7) 1.72" (43.8) 1.29" (33.0) 0.11”