Embedded Power for Business-Critical Continuity Rev. 09.15.09_12 LPS120 Series 1 of 3 LPS120 Series 120 Watts Total Power: 80 - 130 Watts Input Voltage: 85 - 264 VAC # of Outputs: Single Electrical Specifications Special Features Input • Active power factor correction Input range: 85 - 264 VAC ; 127 - 300VDC • 3” x 5” footprint Frequency: 47 - 440 Hz • Less than 1U high Inrush current: 40 A max., cold start @ 25 °C • EN61000-3-2 compliant Efficiency: 80% typical at full load • Remote sense EMI/RFI: • Power fail and remote inhibit FCC Class B conducted; CISPR22 Class B conducted; EN55022 Class B con- • Single wire current sharing ducted; VDE0878PT3 Class B conducted • Adjustable main output Power factor: 0.99 typical • Built-in Class B EMI filter 0.5 mA @ 50/60 Hz, 264 VAC input Safety ground • Overvoltage protection leakage current: • Overload protection Output • Thermal overload protection Maximum power: 80 W for convection ; 130 W with 30CFM forced air • 5 V Standby output and 12V Fan output Adjustment range: ± 5% minimum on the main outputs Fan output: 12 V @ 500mA - 5%, +7% Standby outputs: 5V @ 500mA ± 5% Hold-up time: 20ms @ 125 W load, 120 VAC input Overload protection: Short circuit protection on all outputs. Case overload protected @ 120 - 135% above rating Overvoltage protection: 20 - 35% above nominal output Remote sense: Compensates for 0.5 V lead drop max. Will operate without remote sense connected. Reverse connection protected. Logical Control Power failure: TTL logic signal goes high 100 - 500 msec after main output; it goes low at Safety least 4 msec before loss of regulation TUV: 60950 Remote inhibit: Requires a contact closure to disable the outputs, except 5 V standby. UL: 60950 Remote sense: Compensates for 0.5 V lead drop min. Will operate without remote sense CSA 60950 connected. Reverse connection protected. NEMKO: 60950 AUSTEL: 60950 CB: Certificate and report CE: Mark (LVD) 1 SK2 2 NEUTRAL SK1 LIVE SK3 P1 EARTH Embedded Power for Business-Critical Continuity Rev. 09.15.09_128 LPS120 Series Environmental Specifications 2 of 3 Operating temperature: 0° to 50 °C ambient derate each Mechanical Drawing output as 2.5% per degree from 3.00 50° to 70 °C. -20 °C start up (76.2) Storage temperature: -40 °C to +85 °C 2.55 Electromagnetic Designed to meet EN61000-4; (64.8) susceptibility: -2, -3, -4, -5, -6, -8, -11 Level 3 0.15" DIA. 4 places (4.0) Operating; non-condensing Humidity: 10% to 95% RH IEC68-2-6 to the levels of Vibration: IEC721-3-2 > 550,000 hours at full load and MTBF demonstrated 25 °C ambient conditions 5.00 (127.0) 4.55 (115.6) V Adjust M3.5 (2 places) POT 1.29 (32.8) 1 5 6 10 SK3 0.20" (5) Embedded Power for Business-Critical Continuity Rev. 09.15.09_12 Americas LPS120 Series Ordering Information 3 of 3 5810 Van Allen Way Maximum Load Maximum Load Ripple Model Output Minimum 2 Carlsbad, CA 92008 with Convection with 30CFM Peak Load Regulation P/P Number Voltage Load 3 Cooling Forced Air (PARD) USA Telephone: +1 760 930 4600 LPS121 3.3 V 0 A 21 A 36 A 29 A ± 2% 50 mV Facsimile: +1 760 930 0698 LPS122 5 V 0 A 16 A 26 A 29 A ± 2% 50 mV LPS123 12 V 0 A 6.7 A 10.8 A 12.8 A ± 2% 120 mV Europe (UK) Waterfront Business Park LPS124 15 V 0 A 5.3 A 8.7 A 10.0 A ± 2% 150 mV Merry Hill, Dudley LPS125 24 V 0 A 3.4 A 5.4 A 6.3 A ± 2% 240 mV West Midlands, DY5 1LX United Kingdom LPS128 48 V 0 A 1.7A 2.7 A 3.2 A ± 2% 480 mV Telephone: +44 (0) 1384 842 211 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. Facsimile: +44 (0) 1384 843 355 2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Asia (HK) 3. Peak-to-peak with 20 MHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line volt- 14/F, Lu Plaza age and load ranges. 2 Wing Yip Street 4. When in parallel a 10% load is required for each power supply. Kwun Tong, Kowloon Hong Kong Pin Assignments Telephone: +852 2176 3333 Facsimile: +852 2176 3888 Connector LPS120 For global contact, visit: SK1 Pin1 Neutral Pin3 Line www.PowerConversion.com techsupport.embeddedpower SK2 TB-1 COMMON @emerson.com TB-2 Main output While every precaution has been taken to ensure SK3 Pin1 +V1 Remote sense accuracy and completeness in this literature, Emerson Pin2 -V1 Remote sense Network Power assumes no responsibility, and disclaims Pin3 +Remote inhibit all liability for damages resulting from use of this information or for any errors or omissions. Pin4 -Remote inhibit Pin5 +Power fail Pin6 Common Emerson Network Power. Pin7 SWP The global leader in enabling Pin8 +12V business-critical continuity. Pin9 12V common Pin10 +5V standby AC Power Mating Connectors Connectivity (SK1)AC Input: Molex 09-50-8031 (connector) 08-52-0113 (pins) DC Power (SK2)DC Output: Molex series 19141-0058/0063 Spade lug Embedded Computing (SK3) Control Signals: Molex 90142-0010 (USA) Embedded Power PINS: 90119-2110 or Amp: 87977-3 Monitoring PINS: 87309-8 Outside Plant Emerson Network Power Connector Kit # 70-841-020, includes all of the above. Power Switching & Controls Notes: 1. Specifications subject to change without notice. Precision Cooling 2. All dimensions in inches (mm), tolerance is ± .02”. Racks & Integrated Cabinets 3. mounting holes MH1, MH2, MH3 should be grounded for EMI purpose Services 4. Mounting MH1 is safety ground connection 5. Specifications are for convection rating at factory settings Surge Protection at 115 VAC input 25 °C unless otherwise stated. 6. This power supply requires mounting on metal standoffs EmersonNetworkPower.com 0.20” (5m) in height. Emerson Network Power and the Emerson 7. Warranty: 2 year Network Power logo are trademarks and service marks of Emerson Electric Co. 8. Weight: 0.71 lb. / 0.32 kg ©2009 Emerson Electric Co.