POWER LPS170-M Series Data Sheet Medical 175 Watts Total Power: 100 - 175 Watts Input Voltage: 85 - 264 Vac 120 - 300 Vdc # of Outputs: Single SPECIAL FEATURES ƒ Medical safety approvals ƒ Active power factor correction ƒ IEC EN61000-3-2 compliance ƒ Wide range adjustable output; Remote sense on main output ƒ Single wire current sharing ƒ Power fail and remote inhibit ƒ Built-in EMI filter ƒ Low output ripple Electrical Specifications ƒ Overvoltage protection Input ƒ Overload protection Input range 85 - 264 Vac; 120 - 300 Vdc ƒ Thermal overload protection Frequency 47 - 67 Hz ƒ DC power good Inrush current 38 A max, cold start @ 25 °C ƒ 5 V standby output Efficiency 75% typical at full load ƒ 12 V Aux output EMI filter FCC Class B conducted ƒ Optional cover (-C suffix) CISPR 22 Class B conducted ƒ RoHS compliant EN55022 Class B conducted VDE 0878 PT3 Class B conducted SAFETY Power Factor 0.99 typical ƒ TUV 60601-1 Safety ground leakage current <250 μA @ 50/60 Hz, 264 Vac inputs ƒ UL UL2601 Output ƒ CSA CSA 22.2 No. 601.1 Maximum power 110 W convection (75 W with cover) ƒ CB Certificate and report 175 W with 30 CFM forced air (130 W with cover) ƒ CE Mark (LVD) Adjustment range 2:1 wide ratio minimum Standby outputs 5 V @ 2 A regulated ±5% Hold-up time 20 ms @175 W load at nominal line Overload protection Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating Overvoltage protection 10% to 40% above nominal output Aux output 12 V @ 1 A -5 %, +10% LPS170-M Series Data Sheet Logic Control Power failure TTL logic signal goes high 100 - 500 msec after V1 output; It goes low at least 4 msec before loss of regulation Remote inhibit Requires contact closure to inhibit outputs Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. DC - OK TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Environmental Specifications Operating temperature 0° to 50 °C ambient; derate each output at 2.5% per degree from 50° to 70 °C Low temperature start -20 °C Temperature coefficient ±0.4% per °C Storage temperature -40° to 85 °C Electromagnetic susceptibility Designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating; non-condensing 5% to 95% Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75G peak 5Hz to 500Hz, operational MTBF demonstrated >550,000 hours at full load and 25 °C ambient conditions Ordering Information Maximum Load Maximum Load Model Output Minimum Ripple 1 2 with Convection with 30CFM Peak Load Regulation 3 Number Voltage Load P/P(PARD) Cooling Forced Air LPS172-M 5 V (2.5 - 6 V) 0 A 22 A 35 A 38 A ±2% 50 mV LPS173-M 12 V (6 - 12 V) 0 A 9.1 A 15 A 16.5 A ±2% 120 mV LPS174-M 15 V (12 - 24 V) 0 A 7.3 A 12 A 13.2 A ±2% <1% LPS175-M 24 V (24 - 54 V) 0 A 4.5 A 7.5 A 8.2 A ±2% <1% 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 μF in parallel with a 0.1 μF capacitor at rated line voltage and load ranges. 4. Remote inhibit resets OVP latch. 5. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. Note: -C suffix added to the model number indicates cover option. Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ±0.02”. 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Mounting screw maximum insertion depth is 0.12”. 5. Warranty: 2 years 6. Weight: 1.8 lb/0.85 kg LPS170-M Series Data Sheet Mechanical Drawing 7%7% LPS170-M Series Data Sheet Pin Assignments Connector LPS17x SK1 PIN 1 +12 V PIN 2 5 V Standby PIN 3 Common PIN 4 V1 SWP PIN 5 Common PIN 6 +V1 sense PIN 7 Sense common PIN 8 Remote inhibit PIN 9 DC power good PIN 10 POK SK3 TB-1 COMMON TB-2 Main output SK4 PIN 1 GROUND PIN 3 LINE Pin 5 NEUTRAL Mating Connectors AC Input (SK4) Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 DC Outputs (SK3) Molex 19141-0058 Control Signals (SK1) Molex 90142-0010 (USA) PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 Artesyn Embedded Technologies Connector Kit #70-841-016 WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Waterfront Business Park 14/F, Lu Plaza Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street USA West Midlands, DY5 1LX Kwun Tong, Kowloon +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. Specifications subject to change without notice. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. LPS170-M Series-DS 10Jul2017