POWER LPS200-M Series Data Sheet 250 Watts Total Power: 125 - 250 Watts Input Voltage: 90 - 264 Vac # of Outputs: Single SPECIAL FEATURES ƒ Medical and ITE safeties ƒ Active power factor correction ƒ 3” x 5” footprint ƒ Less than 1U high ƒ EN61000-3-2 compliant Electrical Specifications ƒ Remote sense Input ƒ Power fail Input ra nge 90 - 264 Vac; 120 - 300 Vdc ƒ Adjustable main output Frequency 47 - 63 Hz ƒ Built-in Class B EMI filter Inrush current 50 A max., cold start @ 25 °C ƒ Overvoltage protection ƒ Overload protection Efficiency 86% typical at full load ƒ Thermal overload protection EMI/RFI FCC Class B conducted; CISPR22 Class B conducted; EN55022 Class B conducted; VDE0878PT3 Class B conducted ƒ Isolated 12 V Fan output ƒ LPX200 enclosure kit available Power factor 0.99 typical ƒ RoHS compliant Safety ground 275 µA @ 50/60 Hz, 264 Vac input leakage current SAFETY Output ƒ TUV 60950, 60601-1 Maximum power 125 W for convection (100 W for LPS202-M); 250 W (200 W for LPS202-M) with 30CFM forced air ƒ UL 60950, 60601-1 Adjustment range ± 10% minimum on the main outputs ƒ cULus 60950, 60601-1 ƒ CB Certificate & report Fan output 12 V @ 0.5 A convection, @ 1 A forced air isolated, ± 10% ƒ CE Mark (LVD) Hold-up time 16 ms @ 250 W load, 120 Vac input Overload protection Short circuit protection on all outputs. Case overload protected @ 110 - 160% above rating Overvoltage protection 15 - 50% above nominal output Logical Control Power failure Open collector logic signal goes high 100 - 500 msec after main output; it goes low at least 6 msec before loss of regulation Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. LPS200-M Series Data Sheet Environmental Specifications Operating temperature 0 °C to 50 °C ambient derate each output as 2.5% per degree from 50° to 70 °C. -20 °C start up Storage temperature -40 °C to +85 °C Electromagnetic susceptibility Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating; non-condensing 10% to 95% RH Vibration IEC68-2-6 to the levels of IEC721-3-2 MTBF calculated 1 million hours at full load and 25 °C ambient conditions. 230 Vac input, Bellcore Ordering Information 2 Model Number Output Voltage Minimum Maximum Load with Maximum Load with Peak Load Regulation Ripple 3 Load Convection Cooling 30CFM Forced Air P/P (PARD) LPS202-M 5 V 0 A 20 A 40 A 44 A ± 2% 50 mV LPS203-M 12 V 0 A 10.3 A 20.8 A 22 A ± 2% 120 mV LPS204-M 15 V 0 A 8.3 A 16.6 A 18 A ± 2% 150 mV LPS205-M 24 V 0 A 5.2 A 10.4 A 11.5 A ± 2% 240 mV LPS208-M 48 V 0 A 2.6 A 5.2 A 5.8 A ± 2% 480 mV 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2 . At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3 . Peak-to-peak with 20 mHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 4. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. Pin AssignmentsMating Connectors Connector LPS200-M AC Input Molex 09-50-8031 (connector) (SK1) PINS: 08-52-0072 SK1 Pin 1 Neutral Pin 3 Line AC Ground Molex 01-90020001 SK2 TB-1 Common DC Output (SK2) Molex 19141-0058 or 19099-0044 Spade lug based on Cable Ampacity/AWG TB-2 Main output Control Sense Molex 90142-1110 (USA) SK3 Pin 1 +V1 Remote sense (SK3) PINS: 90119-2110 or Pin 2 -V1 Remote sense Amp: 87977-3 Pin 3 N/C PINS: 87309-8 or Landwin: 2580S1003 Pin 4 N/C PINS: 2583T021V Pin 5 +Power fail Artesyn Embedded Technologies Connector Kit #70-841-020, Pin 6 Common includes all of the above. Pin 7 N/C 1. Specifications subject to change without notice. Pin 8 Common 2. All dimensions in inches (mm), tolerance is ± 0.02” (± 0.5 mm) Pin 9 +12 V Fan 3. Mounting holes MH1 and MH2 should be grounded for EMI purposes. 4. Mounting hole MH1 is safety ground connection. Pin 10 +12 Fan Return (isolated) 5. Specifications are for convection rating at factory settings at 115 VAC input, 25 °C unless otherwise stated. 6. This power supply requires mounting on metal standoffs 0.20” (5m) in height. 7. Warranty: 2 years 8. Weight: 0.75 lb/0.34 kg LPS200-M Series Data Sheet Mechanical Drawing (2.5) Max Component Lead Protrusion WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Waterfront Business Park 14/F, Lu Plaza Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street USA West Midlands, DY5 1LX Kwun Tong, Kowloon +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. Specifications are subject to change without notice. © 2018 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. LPS200-M DS 04Jan2018