POWER LPS250 Series Data Sheet 250 Watts Total Power: 250 Watts Input Voltage: 85 - 264 Vac 120 - 300 Vdc # of Outputs: Single SPECIAL FEATURES ƒ Active power factor correction ƒ IEC EN6100-3-2 compliance ƒ Remote sense & remote inhibit ƒ Power fail ƒ Single wire current sharing Electrical Specifications ƒ Built-in EMI filter Input ƒ 2:1 Wide range output voltage adjust Input range 85 - 264 Vac; 120 - 300 Vdc ƒ 2 Supervisory outputs 5 V and 12 V Frequency 47 - 440 Hz ƒ Overvoltage protection Inrush current 20 A max, cold start @ 25 °C ƒ Overload protection Efficiency 75% typical at full load ƒ Thermal overload protection EMI filter FCC Class B conducted and radiated ƒ DC power good CISPR 22 Class B conducted and radiated ƒ 120 kHz switching frequency EN55022 Class B conducted and radiated VDE 0878 PT3 Class B conducted and radiated ƒ RoHS compliant ƒ Cover -C Safety ground leakage current < 0.5 mA @ 50/60 Hz, 264 Vac input ƒ Optional top with fan cover -CF Output ƒ Optional end fan cover -CEF Maximum power With cover: 250 W with 30 CFM forced air. (-C) (-CF) (CEF) SAFETY Supervisory output 5 V @ 100 mA regulated; 12 V @ 500 mA ƒ VDE 60950 Adjustment range 2:1 wide ratio ƒ UL 60950 Hold-up time 20 ms @ 250 W load, 115 VAC nominal line ƒ CSA 60950 Overload protection Short circuit protection on all outputs. Case overload protected @ ƒ NEMKO 60950 10 - 145% above peak rating ƒ CB Certificate and report 2186 Overvoltage protection 5 V output: 5.7 to 6.7 Vdc. Other models 10% to 25% above nominal output ƒ CE Mark (LVD) Logical Control Power failure TTL Logic signal goes high 50 - 150 msec after 5 V output. It goes low at least 4 ms before loss of regulation Remote on/off Requires an external contact (N.O or N.C) to inhibit outputs DC - OK TTL logic goes high 50 - 150 msec after the output. It goes low when there is loss of regulation. Remote sense Compensates for 0.5 V lead drop minimum, will operate without remote sense connected. Reverse connection protected LPS250 Series Data Sheet Environmental Specifications Operating temperature 0° to 50 °C ambient; derate each output at 2.5% per degree from 50° to 70 °C Storage temperature -40 °C to +85 °C Temperature coefficient ± 0.4% per °C Electromagnetic susceptibility Designed to meet IEC 801, -2, -3, -4, -5, -6, Level 3 Humidity Operating; non-condensing 5% to 95% Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.7 G peak 5 Hz to 500 Hz, operational MTBF demonstrated > 550,000 hours at full load and 25 °C ambient conditions Ordering Information Model Output Minimum Maximum Load with Ripple 1 2 Peak Load Regulation 3 Number Voltage Load 30CFM Forced Air P/P (PARD) LPS252-C 5 V (3 - 6 V) 1.50 A 50 A 60 A ±2% 50 mV LPS253-C 12 V (6 - 12 V) 0.63 A 21 A 25 A ±2% 120 mV LPS254-C 15 (12 - 24 V) 0.50 A 16.7 A 20 A ±2% 150 mV LPS255-C 24 V (24 - 48 V) 0.32 A 10.4 A 12.5 A ±2% 240 mV 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. 2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 μF in parallel with a 0.1 μF capacitor at rated line voltage and load ranges. 4. If optional CF or CEF fans are not used, 30CFM forced air cooling needs to be provided and is required through the length of the power supply. Not convection rated. 5. Output voltage adjustment requires a minimum load. 6. Remote inhibit resets OVP latch 7. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. Note: -CF suffix added to the model number indicates cover with top fan. -CEF suffix added to the model number indicates cover with dual end mounted fan cover and AC inlet. O/P ADJ. LPS250 Series Data Sheet Mechanical Drawing M3 (4 places) 6-32 (2 places) #6-32 (4 places) Main Output #6-32 #6-32 SK3 .24 (6.1) 10.0 Terminal Block TB1 12345678 M3 +ve -ve SK5 SK4 10.0 3.68 FAN (93.6) SK7 FAN 5.46 (138.6) 6.64 (168.6) Optional (-CF) Optional 3.15 Cover 8.52 (-CF) (80) with Fan (216.4) Cover with Fan 9.0 (228.6) 10.32 (262.0) M3 2.17 (55) Optional Optional 1.18 (30.0) 3 2 1 (-CEF) 10.0 6-32 (3 places) (-CEF) Cover SK1 Cover with fans with fans #6-32 2.0 5.0 (127.0) (50.8) 3.0 (76.2) .55 1.30 (14) (33.0) AC Inlet .79 3.42 (87.0) (20) Pin Assignments Mating Connectors Connector SK3 Molex 22-01-1084 SK1 PIN 1 Neutral PINS:08-70-0057 PIN 2 Line SK4 Molex 22-01-3027 PINS: 08-50-0114 PIN 3 Ground SK3 PIN 1 + Remote sense SK5 Molex 22-01-3027 PINS: 08-50-0114 PIN 2 - Remote sense PIN 3 Remote inhibit (N.O.) SK7 Molex 22-01-3027 PINS: 08-50-0114 PIN 4 Remote inhibit (N.C.) PIN 5 Common Artesyn Embedded Technologies Connector Kit #70-841-005, includes all of the above PIN 6 Current sharing 1. Specifications subject to change without notice. PIN 7 Power fail 2. All dimensions in inches (mm), tolerance is ± 0.02”(± 0.5 mm) PIN 8 DC Power Good SK4 PIN 1 + Fan’s power source (12 V @ 500 mA) 3. Specifications are at factory settings. PIN 2 - Fan’s power source (12 V @ 500 mA) 4. To enable normally closed remote inhibit, cut jumper J1. SK5 PIN 1 + Supervisory output supply (5 V @ 100 mA) 5. Mounting maximum insertion depth is 0.12”. PIN 2 - Supervisory output supply (5 V @ 100 mA) 6. Warranty: 2 year SK7 PIN 1 + Fan’s power source (12 V @ 500 mA) 7. Weight: 2.6 lb / 1.19 kg PIN 2 - Fan’s power source (12 V @ 500 mA) WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade For support: productsupport.ep@artesyn.com names, trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. LPS250 DS 18Mar2016