POWER LPT100-M Series Data Sheet 130 Watts Total Power: 80 - 130 Watts Input Voltage: 90 - 264 Vac # of Outputs: Triple SPECIAL FEATURES ƒ Medical and ITE safeties ƒ Active power factor correction ƒ 2” x 4” footprint ƒ Less than 1U high ƒ EN61000-3-2 compliant ƒ Remote sense ƒ Power fail ƒ Adjustable main output Electrical Specifications ƒ Built-in Class B EMI filter Input ƒ Overvoltage protection Input ra nge 90 - 264 Vac; 127 - 300 Vdc ƒ Overload protection Frequency 47 - 63 Hz ƒ Thermal overload protection Inrush current 50 A max., cold start @ 25 °C ƒ LPX100 enclosure kit available ƒ RoHS compliant Efficiency 82% typical at full load EMI/RFI FCC Class B conducted; CISPR22 Class B conducted; EN55022 Class B conducted; VDE0878PT3 Class B conducted SAFETY Safety ground 275 µA @ 50/60 Hz, 264 Vac input ƒ TUV 60950, 60601-1 leakage current ƒ UL 60950, 60601-1 Output ƒ CSA 60950, 60601-1 Maximum power 80 W for convection; ƒ NEMKO 60950, 60601-1 130 W with 200 LFM forced air ƒ AUSTEL 60950, 60601-1 ƒ CB Certificate & report Adjustment range All outputs adjustable: -20%, +10%, except for +24V output on LPT104-M which will be -10%, +20% and 3.3 V output on the LPT101- ƒ CE Mark (LVD) M +10%, -15% Hold-up time 10 ms @ 130 W load, 120 Vac input Overload protection Short circuit protection on all outputs. Case overload protected @ 110 - 160% above rating for V1 & V2, 150 - 250% for V3 Overvoltage protection 15 - 35% above nominal output Logical Control Power failure Active LowTTL logic signal goes high 100 - 500 msec after main output; it goes low at least 6 msec before loss of regulation Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. LPT100-M Series Data Sheet Environmental Specifications Operating temperature 0 °C to 50 °C ambient derate each output as 2.5% per degree from 50 °C to 70 °C. -20 °C start up Storage temperature -40 °C to +85 °C Electromagnetic susceptibility: Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating; non-condensing 10% to 90% RH, non-operating, non-condensing 10% - 95% Vibration IEC68-2-6 to the levels of IEC721-3-2 MTBF calculated 583,000 hours at full load and 25 °C ambient conditions. 230 Vac input, Bellcore Mechanical Drawing ADJUST POT'S SK3 OUTPUT VOLTAGE SEE DETAIL A 1 GND SK2 PIN 1 (LIVE) SK1 8 PIN 3 (NEUTRAL) 0.16 1 3.72 " [4] POWER FAIL [94,6] 4 places mounting hole COMMON max screw head 4 " (+) REMOTE SENSE [101,6] diameter 0.22"[5.6] (-) REMOTE SENSE 4 SK3 DETAIL A 2 " [50,8] 0.1 " [2,5] max lead protrusion 0.197 [5] min stand-o 1.29 " height [32,7] 1.72 " [43,8] LPT100-M Series Data Sheet Ordering Information Ripple Minimum Maximum Load with Maximum Load with 2 Model Number Output Voltage Peak Load Regulation 3 Load Convection Cooling 30CFM Forced Air P/P (PARD) +3.3 V 0 A 13 A 18 A 20 A ±2% 50 mV LPT101-M +5 V 0 A 5 A 9 A 10 A ±5% 50 mV +12 V 0 A 1 A 2.3 A 2.3 A ±5% 120 mV +5 V 0 A 13 A 18 A 20 A ±2% 50 mV LPT102-M +12 V 0 A 5 A 9 A 10 A ±5% 120 mV -12 V 0 A 1 A 2 A 2 A ±5% 120 mV +5 V 0 A 13 A 18 A 20 A ±2% 50 mV LPT103-M +15 V 0 A 4 A 7.2 A 8 A ±5% 150 mV -15 V 0 A 1 A 1.5 A 2 A ±5% 150 mV +5 V 0 A 13 A 18 A 20 A ±2% 50 mV LPT104-M +24 V 0 A 1.5 A 3 A 3.5 A ±7% 240 mV +12 V 0 A 1 A 2.3 A 2.3 A ±5% 120 mV 1. Peak current lasting < 15 seconds with a maximum 10% duty cycle. 2 . At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3 . Peak-to-peak with 20 mHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 4. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. LPT100-M Series Data Sheet Pin Assignments Mating Connectors Connector LPT100-M Molex 09-50-3031 AC Input (SK1) PINS: 08-52-0072 SK1 PIN 1 Live AC Ground Molex 01-90020001 PIN 3 Neutral JST VHR-8N DC Output (SK2) SK2 PIN 1 V1out PINS: SVH-21T-P1.1 PIN 2 V1out JST PHR-4; PINS: SPH-002T-PO.5S Remote Sense PIN 3 GND (SK3) OR PIN 4 GND LANDWIN 2001S0400; PINS: 2005T PIN 5 GND Artesyn Embedded Technologies Connector Kit #70-841-026, includes all of the above PIN 6 GND PIN 7 V2out Notes: 1. Specifications subject to change without notice. PIN 8 V3out 2. All dimensions in inches (mm), tolerance is ±.02”. SK3 PIN 1 Power Fail 3. All mounting holes should be grounded for EMI purpose PIN 2 GND 4. Mounting M1 is safety ground connection PIN 3 + Remote Sense 5. Specifications are for convection rating at factory settings at 115 Vac input 25 °C unless otherwise stated. PIN 4 - Remote Sense 6. This power supply requires mounting on metal standoffs 0.20” (5 m) in height. 7. For DC input an external DC safety rated fuse must be used. 8. Warranty: 2 year 9. Weight: 0.44 lb. / 0.20 kg WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street Kwun Tong, Kowloon USA West Midlands, DY5 1LX +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. LPT100-M DS 21Mar2016