process yellow 116 1375 1797 375 3405 313 2985 240 Embedded Power for Business-Critical Continuity 242 2607 Rev. 11.2.09_69 NFS110 Series 1 of 5 652 NFS110 Series Single & Quad output Total Power: 80 - 110 W Input Voltage: 85 - 264 Vac 120 - 370 Vdc # of Outputs: Single, quad Electrical Specifications Special Features Output • 7.0 x 4.25 x 1.8 inch package Voltage adjustability: +5.1 V o/p on multi’s 3.0% • Overvoltage and short circuit 5.1 V single output 3.0% protection 12 V single output 12 - 14 V • 110 W with 20 CFM 15 V single output 15 - 18 V • Adjustable outputs 24 V single output 24 - 30 V • EN55022, EN55011 conducted Line regulation: LL to HL, FL ±0.1% max. emissions level B All outputs on all units • UL, VDE and CSA safety Overshoot/undershoot: At turn-on 0% approvals • CE mark Temperature coefficient: All outputs ±0.02%/°C • Available RoHS compliant Overvoltage protection: Multi o/p 5.1 V only 6.25 V ± 0.75 V • 2 year warranty 5.1 V single output 6.25 V ± 0.75 V 12 V single output 15.75 V ± 1.0 V 15 V single output 22 V ± 1.5 V 24 V single output 33 V ± 2.5 V Output power limit: Primary power limited Pin max. 160 W Pout min. 110 W Minimum output current: (See Note 13) 0 A Safety Short circuit protection: Burst mode operation • VDE0805/EN60950/ Input • IEC950/IEC1010 Input voltage range: 85 - 264 Vac File No. 10401-3336-0213 120 - 370 Vdc • Licence No. 4001467 7 Input frequency range: 47 - 440 Hz • UL1950 File No. E132002 Input surge current: • CSA C22.2 No. 950 230 Vac 35 A File No. LR41062C Safety ground leakage current: 110 Vac, 50 Hz 0.2 mA, max. 230 Vac, 50 Hz 0.4 mA, max. All specifications are typical at nominal input, full load at 25 °C unless otherwise stated process yellow 116 1375 1797 375 3405 313 2985 240 242 Embedded Power for Business-Critical Continuity 2607 Rev. 11.2.09_69 NFS110 Series 2 of 5 652 EMC Characteristics Conducted emissions: EN55022, FCC part 15 Level B Radiated emissions: EN55022, FCC part 15 Level A ESD air: EN61000-4-2, level 3 Perf. criteria 1 ESD contact: EN61000-4-2, level 4 Perf. criteria 1 Surge: EN61000-4-3, level 3 Perf. criteria 1 Fast transients: EN61000-4-4, level 3 Perf. criteria 1 Radiated immunity: EN61000-4-5, level 3 Perf. criteria 2 Conducted immunity: EN61000-4-6, level 3 Perf. criteria 1 General Specifications Hold-up time: 110 Vac @ 80 W 35 ms 110 Vac @ 110 W 17 ms 230 Vac @ 80 W 140 ms 230 Vac @ 100 W 100 ms Efficiency: Multiple outputs 70% typical +5.1 V single 70% typical 12 V and 15 V singles 72% typical 24 V single 75% typical Isolation voltage: Input/output 3000 Vac Input/chassis 1500 Vac Approvals and standards: VDE0805, EN60950, IEC950, IEC1010, UL1950, CSA C22.2 No. 950 (see note 12) Weight: Singles 550 g (19.4 oz) Multiple outputs 600 g (21.2 oz) MTBF (@25 ºC): MIL-HDBK-217E 125,000 hours min. Environmental Specifications Thermal performance: Operating ambient 0° C to +70 °C (See notes 9, 10) Non-operating -40 °C to +85 °C 0 °C to 50 °C convection cooled 80 W +50 °C to +70 °C, convection cooled Derate 2 W/°C 0 °C to +50 °C, 20 CFM forced air 110 W +50 °C to +70 °C, 20CFM forced air Derate 2.75 W/°C Peak, 0 °C to +50 °C, max. 60 seconds 110W Relative humidity: Non-condensing 5 to 95% RH Altitude: Operating 10,000 feet max. Non-operating 40,000 feet max. Vibration: 5 - 500 Hz 2.4 G rms peak (See Note 11) process yellow 116 1375 1797 375 3405 313 2985 240 242 Embedded Power for Business-Critical Continuity 2607 Rev. 11.2.09_69 NFS110 Series 3 of 5 652 Ordering Information Output Currents Output Total (4) (13, 15, F) Ripple Model Numbers (5) (1) (2) (3) Voltage Regulation Max Peak Fan (14) +5.1 V 8 A 20 A 10 A 50 mV ± 2.0% NFS110-7601PJ +12 V 4.5 A 9 A 5 A 120 mV ± 3.0% –12 V 0.5 A 1.5 A 1 A 120 mV ± 3.0% –5 V 0.5 A 1.5 A 1 A 50 mV ± 3.0% (6, 14) +5.1 V (I ) 8 A 20 A 10 A 50 mV ± 2.0% NFS110-7602PJ A (6) +24 V (I ) 3.5 A 4.5 A 4.5 A 240 mV +10/–5.0% B +12 V 4.5 A 9 A 5 A 120 mV ± 3.0% –12 V 0.5 A 1.5 A 1 A 120 mV ± 3.0% (14) +5.1 V 8 A 20 A 10 A 50 mV ± 2.0% NFS110-7604PJ 15 V 4 A 7.5 A 5 A 150 mV ± 4.0% -15 V 0.5 A 1.5 A 1 A 150 mV ± 3.0% -5 V 0.5 A 1.5 A 1 A 50 mV ± 3.0% (7,8) 12 V 7 A 9 A 9 A 120 mV ± 2.0% NFS110-7612J (7,8) 15 V 5 A 7.3 A 7.3 A 150 mV ± 2.0% NFS110-7615J (7,8) 24 V 3.5 A 4.5 A 4.5 A 240 mV ± 2.0% NFS110-7624J Notes Transient Response 1 Convection cooled, 80 W maximum. 2 Peak outputs lasting less than 60 seconds with duty cycle less than 10%. Total NFS110-7601PJ +5.1 V (7.5 A to 10 A) 150 mV peak, 1 ms recovery peak power must not exceed 110 W. +12 V (2.5 A to 5 A) 100 mV peak, 0.5 ms recovery 3 Forced air, 20 CFM at 1 atmosphere, 110 W maximum. 4 Figure is peak-to-peak. Output ripple is measured across a 50 MHz bandwidth -12 V (0.5 A to 1 A) 100 mV peak, 0.5 ms recovery using a 12 inch twisted pair terminated with a 47 µF capacitor. -5 V (0.5 A to 1 A) 100 mV peak, 0.5 ms recovery 5 Total regulation is defined as the static output regulation at 25 °C, including initial tolerance, line voltage within stated limits and output voltages adjusted NFS110-7602PJ to their factory settings. +5.1 V (7.5 A to 10 A) 150 mV peak, 1 ms recovery 6 To achieve stated regulation on the 24 V output on the NFS110-7602PJ, the +24 V (1.5 A to 3 A) 300 mV peak, 1 ms recovery following load condition must be true: I / I ≤ 5, where: A B +12 V (2.5 A to 5 A) 100 mV peak, 0.5 ms recovery I = +5.1 V output current, and A I = +24 V output current -12 V (0.5 A to 1 A) 100 mV peak, 0.5 ms recovery B The +24 V output will maintain ±5.0% regulation under the following additional condition: I ≤ 5 A. NFS110-7604PJ +5.1 V (7.5 A to 10 A) 150 mV peak, 1 ms recovery A 7 Single output models have floating outputs which may be referenced as +15 V (2.5 A to 5 A) 100 mV peak, 0.5 ms recovery either positive or negative. Higher voltage supplies may be adjusted over a -15 V (0.5 A to 1 A) 100 mV peak, 0.5 ms recovery wide output voltage range, as long as the total output power does not exceed 80 Watts (natural convection) or 110 Watts (forced air). -5 V (0.5 A to 1 A) 100 mV peak, 0.5 ms recovery 8 Power fail detect not available on single output models. 9 Derating curve is application specific for ambient temperatures >50 °C, NFS110-7605J +5.1 V (10 A to 20 A) 250 mV peak, 1 ms recovery for optimum reliability no part of the heatsink should exceed 90 ºC and no semiconductor case temperature should exceed 100 ºC. NFS110-7612J: +12 V (4.5 A to 9 A) 360 mV peak, 1 ms recovery 10 Caution: Allow a minimum of 1 second after disconnecting the power when making thermal measurements. 11 Three orthogonal axes, random vibration, 10 minute test for each axis. NFS110-7615J +15 V (3.65 A to 7.3 A) 450 mV peak, 1 ms recovery 12 This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. NFS110-7624J +24 V (2.25 A to 4.5 A) 720 mV peak, 1 ms recovery 13 Recommend a minimum load of 11 W to achieve the design MTBF. See the derating curve on page 4. 14 Power failure detec is optional by including the suffix “P” to the model number. 15 The ‘J’ suffix indicates that these parts are Pb-free (RoHS 6/6) compliant. 16 NOTICE: Some models do not support all options. Please contact your local Emerson Network Power representative or use the on-line model number search tool at http://www.PowerConversion.com to find a suitable alternative. process yellow 116 1375 1797 375 3405 313 2985 240 242 Embedded Power for Business-Critical Continuity 2607 Rev. 11.2.09_69 NFS110 Series 4 of 5 652 OPTIONAL POWER FAIL DETECT TIMING DIAGRAM AC (J1) mating connector Power fail detect signal (Note 8) AC INPUT Molex 09-50-3051 or Molex 09-91-0500 mating connector with 2478 50ms ≤ T1 ≤ 200ms 4.75V 4.75V or equivalent crimp terminals. T2 will vary with line and load 5V OUTPUT T3 ≥ 3ms HIGH Pout: 110W DC (J2) mating connector 3.5V MIN LOW PFD output is an open collector which PFD SIGNAL Molex 09-50-3131 or Molex 09-91-1300 mating connector with 2478 0-0.4 MAX will sink ≤ 40mA in the low state. T3 or equivalent crimp terminals. T1 T2 0.475 0.010 (12.07) DERATING CURVE (See Notes 9, 10) 1.80 (45.72) MAX 1.00 0.005 Output Power (Watts) (25.4) 110W 20 CFM FORCED AIR COOLING 6-32 UNC 0.050 0.020 1.55 0.005 (4PL) 3.35 0.015 (85.09) 80W (1.27) (39.37) PIN 1 Voltage Adjust Optional NATURAL Power Fail J2 55W Detect Circuit CONVECTION 4.250 0.020 (Key = Pin 2) COOLING 40W (107.95) T1 T1 3.750 Pin 1 0.005 (95.25) PIN 1 L1 11W 11W MINIMUM LOAD REQUIRED AT 230VAC 0W 0.156 J1 DIA. HOLE 0C 10C 20C 30C 40C 50C 60C 70C C6 (4PL) F1 5A, 250 VAC Pin Connections 0.250 6.50 0.005 (165.1) 0.010 (6.35) J1 -7601PJ -7602 P -7604PJ Singles 7.00 0.020 (177.8) Pin 1 AC Ground AC Ground AC Ground AC Ground 0.250 0.010 ALL DIMENSIONS IN INCHES (mm) (6.35) Pin 2 AC Neutral AC Neutral AC Neutral AC Neutral Pin 3 AC Line AC Line AC Line AC Line Mechanical Notes: A Metallic or non-metallic stand-offs (maximum diameter 5.4mm) can be used in all four mounting holes J2 without effecting safety approval. Pin 1 +5.1 V +5.1 V +5.1 V V B The ground pad of the mounting hole near J1, allows system grounding through a metal stand-off to out the system chassis. Pin 2 +5.1 V +5.1 V +5.1 V V out C The heat sink is grounded, and allows system grounding by mechanical connection to the system chassis. Pin 3 +5.1 V +5.1 V +5.1 V V out D The supply must be mechanically supported using the PCB mounting holes and may be additionally supported by the heatsink mounting holes. Pin 4 Return Return Return Return E It is always advisable to attach the power supply heat sink to another thermal dissipator (such as a Pin 5 Return Return Return Return chassis or finned heatsink etc). The resulting decrease in heat sink mounted component temperatures will improve power supply lifetime. Pin 6 Return Return Return Return F A standard L-bracket and cover is available for mounting which contains all screws, connectors and necessary mounting hardware. The kit is available, order part number “NFS110CJ” . Pin 7 Return Return Return Return Pin 8 +12 V +12 V +15 V V out Pin 9 +12 V +12 V +15 V V out Pin 10 PFD PFD PFD N/C Pin 11 -12 V -12 V -15 V N/C Pin 12 Removed for Key Pin 13 -5 V +24 V -5 V N/C N/C = no connection process yellow 116 1375 1797 375 3405 313 2985 240 Embedded Power for Business-Critical Continuity 242 2607 Rev. 11.2.09_69 NFS110 Series Americas 5 of 5 652 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.PowerConversion.com techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2009 Emerson Electric Co.