POWER NFS110 Medical Series Data Sheet Single and quad output Total Power: 80 - 110 W Input Voltage: 100 - 240Vac 127 - 357 Vdc # of Outputs: Single, quad Special FeatureS ƒ 7.0 x 4.25 x 1.8 inch package ƒ Medical, dental and laboratory applica- tions ƒ Overvoltage and short circuit protection ƒ 110 W with 20 CFM ƒ UL, cUL and VDE approvals ƒ EN60601-1 and UL2601 medical approvals ƒ Available RoHS compliant Electrical Specifications ƒ 2 years warranty Output Voltage adjustability: +5.1 V o/p on multi’s ± 3.0% SaFety 5.1 V single output ± 3.0% ƒ EN60950-1/IEC60950-1 12 V single output 12 - 14 V ƒ EN60601-1 15 V single output 15 - 18 V 24 V single output 24 - 30 V ƒ UL60601-1/CSA C22.2 No. 601-1 File No. E182560 Line regulation: LL to HL, FL ± 0.1% max. All outputs on all units Overshoot/undershoot: At turn-on no lead 0% Temperature coefficient: All outputs ±0.02% / °C Overvoltage protection: Multi o/p 5.1 V only 6.25 V ± 0.75 V 5.1 V single 6.25 V ± 0.75 V 12 V single 15.75 V ± 1.0 V 15 V single 22 V ± 1.5 V 24 V single 33 V ± 2.5 V Output power limit: Primary power Pin max. 160 W limited Pout min. 110 W Short circuit protection: Burst mode operation Input Input voltage range: 100 - 240 Vac 127 - 357 Vdc Input frequency range: 47 - 440 Hz Input surge current: 110 Vac. 50 Hz 17 A 230 Vac. 50 Hz 25 A Safety ground leakage 132 Vac 50 μA current: 264 Vac 100 μA All specifications are typical at nominal input, full load at 25 °C unless otherwise stated NFS110 Medical Series Data Sheet EMC Charateristics Conducted emissions: EN55022, FCC part 15 Level A Radiated emissions: EN55022, FCC part 15 Level A ESD air: EN61000-4-2, level 3 Perf. criteria 1 ESD contact: EN61000-4-2, level 4 Perf. criteria 1 Surge: EN61000-4-3, level 3 Perf. criteria 1 Fast transients: EN61000-4-4, level 3 Perf. criteria 1 Radiated immunity: EN61000-4-5, level 3 Perf. criteria 2 Conducted immunity: EN61000-4-6, level 3 Perf. criteria 2 General Specifications Hold-up time: 110 Vac @ 80 W 35 ms 110 Vac @ 110 W 17 ms 230 Vac @ 80 W 140 ms 230 Vac @ 110 W 100 ms Efficiency: Multiple outputs 70% typical +5.1 V single 70% typical 12 V and 15 V singles 72% typical 24 V single 75% typical Isolation voltage: Input/output 4000 Vac Input/chassis 1500 Vac Approvals and standards: VDE0750, IEC60601, IEC1010, UL60601, CSA (see note 12) C22.2 No. 125 Singles 550 g (19.4 oz) Weight: Multiple outputs 600 g (21.2 oz) MTBF (@25 ºC) MIL-HDBK-217E 125,000 hours min. Environmental Specifications Thermal performance: Operating, see curve 0°C to +70°C (See notes 9, 10) Non-operating -40°C to +85°C 0 °C to 50 °C amb. convection cooled 80 W +50 °C to +70 °C, amb. convection cooled Derate 2 W/°C 0 °C to +50 °C, 20 CFM forced air 110 W +50 °C to +70 °C, 20CFM forced air Derate 2.75 W/°C Relative humidity: Peak, 0 °C to +50 °C, max. 60 seconds 110W Altitude: Non-condensing 5% to 95% RH Operating 10,000 feet max. Non-operating 40,000 feet max. Vibration (See Note 11): 5-500 Hz 2.4 G rms peak NFS110 Medical Series Data Sheet Ordering Information Output Currents Output Total (4) (13, 14, F) Ripple Model Numbers (5) (1) (2) (3) Voltage Regulation Max Peak Fan +5.1 V 8 A 20 A 10 A 50 mV ± 2.0% NFS110-7901PJ +12 V 4.5 A 9 A 5 A 120 mV ± 3.0% –12 V 0.5 A 1.5 A 1 A 120 mV ± 3.0% –5 V 0.5 A 1.5 A 1 A 50 mV ± 3.0% +5.1 V (I ) 8 A 20 A 10 A 50 mV + 2.0% NFS110-7902PJ A (6) +24 V (I ) 3.5 A 4.5 A 4.5 A 240 mV + 10 / – 5.0% B +12 V 4.5 A 9 A 5 A 120 mV ± 3.0% –12 V 0.5 A 1.5 A 1 A 120 mV ± 3.0% (7,8) 12 V 7 A 9 A 9 A 120 mV ± 2.0% NFS110-7912J (7,8) 15 V 5 A 7.3 A 7.3 A 150 mV ± 2.0% NFS110-7915J (7,8) 24 V 3.5 A 4.5 A 4.5 A 240 mV ± 2.0% NFS110-7924J Notes Transient Response 1. Convection cooled, 80 W maximum. NFS110-7901PJ +5.1 V (7.5-10 A) 150 mV peak, 1 ms recovery 2. Peak outputs lasting less than 60 seconds with duty cycle less than 10%. Total peak power must not exceed 110 W. +12 V (2.5-5 A) 100 mV peak, 0.5 ms recovery 3. Forced air, 20 CFM at 1 atmosphere, 110 W maximum. -12 V (0.5-1 A) 100 mV peak, 0.5 ms recovery 4. Figure is peak-to-peak. Output ripple is measured across a 50 MHz -5 V (0.5-1 A) 100 mV peak, 0.5 ms recovery bandwidth using a 12 inch twisted pair terminated with a 47 μF NFS110-7902PJ +5.1 V (7.5-10 A) 150 mV peak, 1 ms recovery capacitor. 5. Total regulation is defined at the static output regulation at 25 °C, +12 V (2.5-5 A) 100 mV peak, 0.5 ms recovery including initial tolerance, line voltage within stated limits and output -12 V (0.5-1 A) 100 mV peak, 0.5 ms recovery voltages adjusted to their factory settings. Also for NFS110-7902PJ, for 24 V (1.5-3 A) 300 mV peak,1 ms recovery 24 V output stated regulation I / I ² 5. This output will maintain ±5.0% A B NFS110-7905J +5.1 V (10-20 A) 250 mV peak, 1 ms recovery regulation if I ² 5 A, where I = +5.1 V output current and I = +24 V A A B output current. NFS110-7912J +12 V (4.5-9 A) 360 mV peak, 1 ms recovery 6. Single output models have floating outputs which may be referenced as NFS110-7915J +15 V (3.65-7.3 A) 450 mV peak, 1 ms recovery either positive or negative. Higher voltage supplies, may be adjusted NFS110-7924J +24 V (2.25-4.5 A) 720 mV peak, 1 ms recovery over a wide output voltage range, as long as the total output power does not exceed 80 Watts (natural convection) or 110 Watts (forced air). 7. Power fail detect not available on single output models. 8. Derating curve is application specific for ambient temperatures > 50 °C, for optimum reliability no part of the heatsink should exceed 90 °C and no semiconductor case temperature should exceed 100 °C. 9. Caution: Allow a minimum of 1 second after disconnecting the power when making thermal measurements. 10. The user should read the PSU installation instructions in conjunction with the relevant national safety regulations in order to ensure compliance. 11. Three orthogonal axes, random vibration, 10 minute test for each axis. 12. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 13. The ‘J’ suffix indicates that these parts are Pb-free (RoHS 6/6) compliant. TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special request, please contact your local sales representative for details. 14. NOTICE: Some models do not support all options. Please contact your local Artesyn Embedded Technologies representative or use the on-line model number search tool at www.artesyn.com/power to find a suitable alternative. NFS110 Medical Series Data Sheet OPTIONAL POWER FAIL DETECT TIMING DIAGRAM AC (J1) mating connector Power fail detect signal (Note 8) Molex 09-50-3051 or Molex 09-91-0500 mating connector 50 ms ≤ T1 ≤ 200 ms AC INPUT with 2478 or equivalent crimp terminals. 4.75V 4.75V T2 will vary with line and load 5V OUTPUT T3 ≥ 3 ms HIGH 3.5V MIN LOW DC (J2) mating connector PFD SIGNAL Pout: 110 W 0-0.4 MAX T3 Molex 09-50-3131 or Molex 09-91-1300 mating connector PFD output is an open collector which will T1 T2 with 2478 or equivalent crimp terminals. sink ≤ 40 mA in the low state. 0.475 0.010 (12.07) 1.80 (45.72) MAX 1.00 0.005 (25.4) DERATING CURVE (See Notes 9, 10) 6-32 UNC 0.050 0.020 Output Power (Watts) 1.55 0.005 (4PL) 3.35 0.015 (85.09) (1.27) (39.37) 110W PIN 1 20 CFM FORCED AIR COOLING Voltage Adjust 80W Optional Power Fail J2 Detect Circuit 4.250 0.020 (Key = Pin 2) NATURAL 55W (107.95) CONVECTION COOLING T1 40W T1 3.750 Pin 1 0.005 (95.25) PIN 1 L1 11W 0.156 11W MINIMUM LOAD REQUIRED AT 230VAC J1 0W DIA. HOLE C6 0C 10C 20C 30C 40C 50C 60C 70C (4PL) F1 5A, 250 VAC 0.250 6.50 0.005 (165.1) 0.010 (6.35) 7.00 0.020 (177.8) 0.250 0.010 J1 ALL DIMENSIONS IN INCHES (mm) (6.35) Mechanical Notes A Metallic or non-metallic stand-offs (maximum diameter 5.4 mm) can be used in all four mounting holes without effecting safety approval. B The ground pad of the mounting hole near J1, allows system grounding through a metal stand-off to the system chassis. C The heat sink is grounded, and allows system grounding by mechanical connection to the system chassis. D The supply must be mechanically supported using the PCB mounting holes and may be additionally supported by the heatsink mounting holes. E It is always advisable to attach the power supply heat sink to another thermal dissipator (such as a chassis or finned heatsink etc). The resulting decrease in heat sink mounted component temperatures will improve power supply lifetime. F A standard L-bracket and cover is available for mounting which contains all screws, connectors and necessary mounting hardware. The kit is available, order part number “NFS110CJ”. NFS110 Medical Series Data Sheet Pin Connections J1 -7901PJ -7902PJ SINGLES Pin 1 AC Ground AC Ground AC Ground Pin 2 AC Neutral AC Neutral AC Neutral Pin 3 AC Line AC Line AC Line J2 Pin 1 +5.1 V +5.1 V V out Pin 2 +5.1 V +5.1 V V out Pin 3 +5.1 V +5.1 V V out Pin 4 Return Return Return Pin 5 Return Return Return Pin 6 Return Return Return Pin 7 Return Return Return Pin 8 +12 V +12 V V out Pin 9 +12 V +12 V V out Pin 10 PFD PFD N/C Pin 11 -12 V -12 V N/C Pin 12 Removed for Key Pin 13 -5 V +24 V N/C N/C = no connection. WORLDWIDE OFFICES americas europe (uK) asia (HK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park Tempe, AZ 85282 Merry Hill, Dudley 2 Wing Yip Street Kwun Tong, Kowloon USA West Midlands, DY5 1LX +1 888 412 7832 United Kingdom Hong Kong www.artesyn.com +44 (0) 1384 842 211 +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn For more information: www.artesyn.com/power Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of For support: productsupport.ep@artesyn.com this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. NFS110 Medical Series-DS 12.19.14 © 2014 Artesyn Embedded Technologies, Inc.