TDK-LAMBDA TPS3000-24

TPS3000 Series 3200W 3 Phase Input Industrial Power Supplies Features  400/440/480 VAC (Nominal) 3 Phase Delta or Wye  Fully Regulated, Wide Range Adjustable Output  Voltage and Current Programming  -40°C (start up) to +70°C operation  >92% EfŢ ciency  PMBus™ Communication  Built in ORing FETs & Active I share for parallel operation  Fully Featured Key Market Segments & Applications SpeciŢ cations Model TPS3000-24 TPS3000-48 Input Voltage (47-63Hz) VAC 350 - 528VAC, Delta or Wye 3 phase Input Current A 6A per phase max, steady state Inrush Current A <15A per phase (excluding initial spike charging EMI capacitors lasting <2ms) Power Factor Correction - 0.93 typical EfŢ ciency (1) % 92.5% 92.5% Ripple & Noise (Pk-Pk) (max) (2) mV 130mV 260mV Line Regulation % <0.25% Load Regulation % <0.5% Overcurrent Protection - Adjustable (70-105% of rated current) Overvoltage Protection V 115% of setpoint (tracking) Thermal Protection - Internal thermostat. Automatic reset Hold Up Time ms >10mS at 80% of rated current, nominal input/output voltage Remote Sense - Compensates for a total of 1V cable drop Dropped Phase (2) - Open collector signal; off during normal operation, strobing during dropped phase state Remote On / Off - Selectable logic - Enable or Inhibit AC Fail Signal - Open Collector, ON when AC is above 340VAC and unit is enabled DC Good Signal - Open Collector, ON when output is above 85 to 95% of setpoint (tracking) Remote Adjust - 0 - 5V adjusts output from V max to V min Parallel Connection - Single wire current share, up to 8 units. Built in ORing FET Standby Voltage - 11.2 - 12.5V, 0.3A Operating Temperature °C -40 to +70°C, see derating curve (20 min warm up needed for <-10°C) Storage Temperature °C -40 to +85°C Temperature CoefŢ cient %/°C 0.02%/°C Humidity (non condensing) %RH 10 - 90%RH Cooling - Internal variable speed fan Withstand Voltage VAC Input - Ground 2,000VAC, Input - Output 3,000VAC, Output - Ground 500VAC Isolation Resistance MΩ >100MΩ (25deg, 70%RH) Vibration - Designed to meet MIL-STD-810F, Method 514.5, Procedure I, Cat 1, 10 Shock - Designed to meet MIL-STD-810F, Method 516.5, Procedure I, IV & VI Safety Agency CertiŢ cations - UL/CSA60950-1, EN60950-1, CE mark for LVD and RoHS2 Voltage Dips - SEMI F47-0706 Leakage Current mA <3mA Conducted & Radiated Emissions - EN55022 Class A, FCC part 15 Class-A Immunity - EN61000-4-2, -3, -4, -5, -6, -8, -11 Altitude m 4,000m Weight kg 3.5 Size (W x H x D) mm 107 x 84.4 x 324mm (excluding output busbars) Warranty yrs Three Years (1) Typical, 75-100% at rated current (2) Consult Installation Manual for detailed speciŢ cations, test methods and application notes 1-800-526-2324 • www.us.tdk-lambda.com/lp/ 54 Disclaimer: us.tdk-lambda.com/lp/legal.htm TPS3000 Series SpeciŢ cations Nominal Adjust. Rated Maximum (3) Rated Maximum (3) Model Voltage (V) Range (V) (4) Current (A) Current (A) Power (W) Power (W) TPS3000-24 24 19.2 - 28.5 125 133.3 3000 3200 TPS3000-48 48 38.4 - 56.5 66.7 66.7 3200 3200 (3) Rating at nominal output voltage only. (4) A minimum load of 0.5A is required to maintain regulation and ripple spec throughout the output voltage adjustment range. Outline Drawing 40.5 125 144 AIR FLOW DIRECTION (SEE NOTE 2) 9 44 84.4 M3 TAPPED HOLE 20.2 M4 THREADED INSERTS 40 3 PLACES 324 260 42 13.5 80 107 NOTES: 1. MOUNTING SCREWS MUST NOT PROTRUDE INTO THE POWER SUPPLY MORE THAN 6mm 2. ALLOW MINIMUM OF 50mm UNRESTRICTED AIR SPACE AT THE REAR OF THE UNIT. DO NOT OBSTRUCT AIR FLOW TO THE UNIT FRONT PANEL. 3. SIGNAL CONNECTOR RECEPTACLE: JST P/N: PHDR-20VS RECEPTACLE CONTACTS: JST P/N: SPHD-001T-P0.5 M4 THREADED INSERTS 4 PLACES (TOP AND BOTTOM) SEE NOTE 1 Derating Curve Recommended Filter RTMN-5010 http://us.tdk-lambda.com/lp/products/r-series.htm For Additional Information, please visit us.tdk-lambda.com/lp/products/tps-series.htm 1-800-526-2324 • www.us.tdk-lambda.com/lp/ 55 Revision A8: Jan 2017