POWER DS1100SLPE Data Sheet 1100 Watts Distributed Power System Front-end Bulk Power Total Output Power: 1100 W continuous Wide Input Voltage: 90 to 264 Vac SPECIAL FEATURES ƒ 1100 W output power ƒ High power and short form factor ƒ 1U power supply 3 ƒ High density design: 26 W/in Electrical Specifications ƒ Active Power Factor Correction Input ƒ EN61000-3-2 harmonic compliance Input range 90 - 264 Vac ƒ Inrush current control ƒ 80plus Platinum Efficiency Frequency 47 Hz to 63 Hz ƒ N+1 or N+N Redundant Efficiency 94.0% peak ƒ Hot-pluggable Max input current 14.5 Arms ƒ Active current sharing Inrush current 55 Apk ƒ Full digital control Conducted EMI Class A +6 dB margin ƒ PMBus compliant Radiated EMI Class A +6 dB margin ƒ Accurate input power reporting Power factor > 0.9 beginning at 20% load ƒ Compatible with Artesyn’s Universal ITHD 10% PMBus GUI Leakage current 1.75 mA ƒ Reverse airflow option Hold-up time 16 ms at full load ƒ Two-year warranty Output Main DC Output Standby DC Output COMPLIANCE ƒ EMI Conducted/Radiated Class A MIN NOM MAX MIN NOM MAX Limits + 6 dB margin Nominal setting -1% 12 +1% -1% 3.3 1% ƒ EN61000-4 Electromagnetic Total output regulation range 11.64 V 12 12.36 V 3.14 V 3.3 3.46 V compatibility Dynamic load regulation range 11.64 V 12.36 V 3.14 V 3.46 V ƒ RoHS 6/6 Output ripple 180 mVp-p 45 mVp-p 1 Output current 0.5 A 90.0 A 0.1 A 3.0 A SAFETY Current sharing Within ±5.625A of each other from N/A ƒ UL/cUL 60950 (UL Recognized) 25% to 100% load ƒ DEMKO+ CB Report EN60950 Capacitive loading 500 µF 11,000 µF 20 µF 1000 µF ƒ CE Mark Start-up from AC to output 2200 ms 1700 ms ƒ China CCC Output rise time 5 ms 50 ms 2 ms 60 ms ƒ BSMI Note: Outputs shall be isolated from the chassis ground by at least 50 V. 1 Minimum starting current for transient load response testing only. Unit is designed to operate and be within output regulation at zero load. DS1100SLPE Data Sheet Electrical Specifications Protections Main Output MIN NOM MAX 2 Overcurrent protection 107% 130% 1 Overvoltage protection 13.5 V 15.0 V Overtemperature protection Yes, autorecovery Fan fault protection Yes Standby Output 3 Overcurrent protection : 110% 150% 1 Overvoltage protection 3.6 V 3.9 V 1 Latch mode 2 No shutdown if the overcurrentis within the range and does notlast for more than 200 ms, otherwise latch will occur 3 Autorecovery Control and Status Signals Input Signals PSON_L Active LOW signal which enables/disables the main output. Pulling this signal LOW will turn-on the main output. Recommended pull-up resistor to VSB is 5.1 kohms. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.6 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK PSKILL_H First break/last mate active LOW signal which enables/disables the main output. This signal will have to be pulled to ground at the system side with a 220 ohm resistor. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.6 V IH I Current that may be sourced by this pin 2 mA SOURCE I Current that may be sunk by this pin at low state 0.5 mA SINK VSENSE+, VSENSE- VSENSE+ and VSENSE- lines are the remote sense lines for regulation. Each line will compensate for a maximum of 100 mV Ordering Information Model Number Nominal Main Output Standby Output Airflow Direction DS1100SLPE-3 12 V 3.3 V @ 3 A Std (forward) 1 DS1100SLPE-3-001 12 V 3.3 V @ 3 A Reverse 1 Derating may apply. I2C Addressing A1 Pin A0 Pin PMBus (w/r) 0 0 B0/B1 0 1 B2/B3 1 0 B4/B5 1 1 B6/B7 DS1100SLPE Data Sheet Control and Status Signals Output Signals ACOK Signal used to indicate the presence of AC input to the power supply. A logic level HIGH will indicate that the AC input to the power supply is within the operating range while a logic level LOW will indicate that AC has been lost. This is an open collector/drain output. This pin is pulled high by a 10 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be onnected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX V Input logic level LOW 0.6 V IL V Input logic level HIGH 2.0 V 3.6 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK PWR_GOOD / PWOK Signal used to indicate that main output voltage is within regulation range. The PWR_GOOD signal will be driven HIGH when the output voltage is valid and will be driven LOW when the output falls below the under-voltage threshold. This signal also gives an advance warning when there is an impending power loss due to loss of AC input or system shutdown request. More details in the Timing Section. This is an open collector/drain output. This pin is pulled high by a 10 kohm resistor connected to 3.3 V inside the power supply. It is recommended that this pin be connected to a 100 pF decoupling capacitor and pulled down by a 100 kohm resistor. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.6 V IH I Current that may be sourced by this pin 3.3 mA SOURCE I Current that may be sunk by this pin at low state 0.7 mA SINK Output Signals PS_PRESENT Signal used to indicate to the system that a power supply is inserted in the power bay. This pin is shorted to the standby return in the power supply. Recommended pull-up resistor to VSB is 5.1 kohms. A 100 pF decoupling capacitor is also recommended. PS_INTERRUPT Active low signal used by the power supply to indicate to the system that a change in power supply status has occurred. This event can be triggered by faults such as OVP, OCP, OTP, and fan fault. This signal can be cleared by a CLEAR_FAULT command. Recommended pull-up resistor to VSB is 5.1 kohms. A 100 pF decoupling capacitor is also recommended. MIN MAX V Input logic level LOW 0.8 V IL V Input logic level HIGH 2.0 V 3.6 V IH I Current that may be sourced by this pin 4 mA SOURCE I Current that may be sunk by this pin at low state 4 mA SINK DS1100SLPE Data Sheet Control and Status Signals BUS Signals ISHARE Bus signal used by the power supply for active current sharing. All power supplies con# gured in the system for n+n sharing will refer to this bus voltage inorder to load share. Voltage Range The range of this signal for active sharing will be up to 8.0 V, which corresponds to the maximum output current. MIN MAX I Voltage Input logic level LOW 7.75 8.25 SHARE Voltage at 50% load, stand-alone unit 3.85 4.15 Voltage at 0% load, stand-alone unit 0 1.0 I Current that may be sourced by this pin 160 mA SOURCE SCL, SDA Clock and data signals de# ned as per I2C requirements. It is recommended that these pins be pulled-up to a 2.2 kohm resistor to 3.3 V and a 100 pF decoupling capacitor at the system side. VL Input logic level LOW 0.8 V VH Input logic level HIGH 2.0 V 3.6 V Note: All signal noise levels are below 400 mVpk-pk from 0 - 100 MHz. Electrical Specifications LED Indicators A single bi-color LED is used to indicate the power supply status. Status LED Fail LED Color Green Amber/Green No input to PSU Off Off Input present, STBY ON, main output OFF On Blinking Amber, at least 1 Hz Main output ON On green Power supply warning (hi-temp) On Blinking Amber/Green, at 2:1 ratio, at least 1 Hz Power supply warning (slow fan) Off Blinking Amber/Green, at 1:1 ratio, at least 1Hz Power supply failure (OVP, OTP, FAN FAULT) On Amber Firmware Reporting And Monitoring Accuracy Range Output loading <10% 10% to 20% 20% to 100% Input voltage ±5% Input current ±1 A fixed error ±10% ±5% Input power 30 W fixed error up to 120 W ±15% ±10% Output voltage ±5% ±2% Output current 0.8 A fixed error ±15% ±5% Temperature ±5 °C Fan speed Actual ±250 RPM PMBus YES Remote ON/OFF YES DS1100SLPE Data Sheet Electrical Specifications Timing Specifications Description Min Max Unit T Delay from AC being applied to standby output being within regulation 2500 ms sb_On T Delay from standby output to ACOK assertion 1500 ms sb_ACOK T Delay from standby output to main output voltage being within regulation 1000 ms sb_Vout T Delay from AC being applied to main output being within regulation 3000 ms AC_On_Delay T Delay from output voltages within regulation limits to PWOK asserted 100 1000 ms PWR_GOOD_On T Delay from loss of AC to assertion of ACOK 20 ms ACOK_Delay T Delay from loss of AC to deassertion of PWOK 5 ms PWR_GOOD_Hold-up T Delay from loss of AC to main output being within regulation 16 ms Vout_Hold-up T Delay from loss of AC to standby output being within regulation 25 ms sb_Hold-up T Delay from deassertion of PWOK to output falling out of regulation 1 700 ms PWR_GOOD_Off T Delay from PSON assertion to output being within regulation 400 ms PSON_On_Delay Timing Diagram AC Input T T sb_Hold-up sb_On T ACOK_Delay Vout_stby T sb_Vout T sb_ACOK ACOK T T AC_On_Delay Vout_Hold-up Vout_main T PWOK_On T PWOK_Off PWOK T PWOK_Hold-up T PSON_On_Delay PSON DS1100SLPE Data Sheet Mechanical Outline Output Connector Pin Configuration Output Connector A1 3.3 VSB Standby Output Output Connector Part Number TEI 2-1926736-2 B1 3.3 VSB Standby Output Mating Connector Part Number TEI 2-1926739-5, 1892787-6 or equivalent C1 3.3 VSB Standby Output D1 3.3 VSB Standby Output E1 3.3 VSB Standby Output A2 SGND Signal Ground B2 SGND Signal Ground C2 Reserved D2 Reserved E2 Reserved A3 A2/A_Select Optional address line 2 B3 A0 I C Address 2 C3 SDA I C Data D3 -Remote_Sense Wire drop compensation E3 +Remote_Sense Wire drop compensation 2 A4 SCL I C Clock B4 PSON_L Enable/Inhibit C4 PS_INTERRUPT_L Alert for failure 2 D4 A1 I C Address E4 ACOK Input indicator A5 PSKILL_L First break/lastmate pin B5 ISHARE Current share bus C5 PWOK Output indicator D5 Reserved E5 PS_PRESENT_L Power supply present P1-P5 +12 V Return Main output return contact P6-P10 12 V Main output power contact DS1100SLPE Data Sheet Environmental Specifications Operating temperature DS1100SLPE-3 Full power at -5 to 55 °C, can operate up to 65 °C at 660 W derated power DS1100SLPE-3-001 Full power at -5 to 45 °C, can operate up to 55 °C at 660 W derated power Operating relative humidity 5% to 90% non-condensing Operating altitude up to 10,000 feet Non-operating temperature -40 to +70 °C Non-operating relative humidity 10% to 95% non-condensing Non-operating altitude up to 50,000 feet Storage temperature -40 to +85 °C Storage relative humidity 5% to 95% non-condensing Vibration and shock Standard operating/non-operating random shock and vibration RoHS compliance Yes MTBF >500,000 hours using Telcordia Issue 2, Method 1 Case 1 at 40 °C ambient at full load. Operating life Minimum of 7 years at typical operating conditions Reliability All electronic component derating analysis and capacitor life calculation is done at 40 °C ambient, 80% of maximum rated load, nominal input line voltage. WORLDWIDE OFFICES Asia (HK) Americas Europe (UK) 14/F, Lu Plaza 2900 S.Diablo Way Waterfront Business Park 2 Wing Yip Street Tempe, AZ 85282 Merry Hill, Dudley Kwun Tong, Kowloon USA West Midlands, DY5 1LX Hong Kong +1 888 412 7832 United Kingdom www.artesyn.com +852 2176 3333 +44 (0) 1384 842 211 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and For more information: www.artesyn.com/power service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, For support: productsupport.ep@artesyn.com trademarks, or registered trademarks of their respective owners. © 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. DS1100SLPE 10Oct2016