EOS POWER WLT200-CK
Specifications
Manufacturer
EOS Power
Manufacturers Part #
WLT200-CK
Factory Pack Quantity
100
Datasheet
Extracted Text
200 Watt Industrial Features l 5 x 3 x 1.5 inches form factor l 200 W with forced-air cooling l High efficiency > 88% l 12 V fan output l 5 V standby output l Remote sense l Output voltage adjustability Electrical Specifications Input Voltage 90-264 VAC/120-390 VDC, Universal Input Frequency 47-63 Hz Input Current 120 VAC: 2.4 A max. 230 VAC: 1.2 A max. No Load Power 0.8 W Inrush Current 120 VAC: 35 A max . 230 VAC: 65 A max. Leakage Current 120 VAC: < 150 µA 230 VAC: < 300 µA Efficiency 120 VAC: 84% typical 230 VAC: 86% typical Hold-up Time 120 VAC > 10 ms 230 VAC > 10 ms Power Factor 120 VAC: 0.99 230 VAC: 0.95 Output Power 160 to 200 W Peak Power 250 W for 0.2 s Line Regulation +/-0.5% Load Regulation +/-2.0% Transient Response < 10%, 50% to 100% load change, 50 Hz, 50% duty cycle, 0.1 A/µs, recovery time < 5 ms Rise Time < 100 ms Set Point Tolerance +/-1% Output Adjustability +/-3.0% Over Current Protection 110% typical above rating Over Voltage Protection 110 to 150% Short Circuit Protection Short term, autorecovery Switching Frequency PFC converter: Variable, 35-250 kHz; 90 kHz typical Resonant converter: Variable, 35-250 kHz; 90 kHz typical Operating Temperature -20 to +70°C, refer derating curve, -20 to 0°C, start-up is guaranteed Storage Temperature -40 to +85°C Relative Humidity 95% Rh, noncondensing Altitude Operating: 10,000 ft.; Nonoperating: 40,000 ft. MTBF 1.6m Hours, Telcordia -SR332-issue 3 Isolation Voltage Min. 4242 VDC between input to output Cooling Convection: 83 W; 300 LFM: 175 W (5 V model) Convection: 160 W; 300 LFM: 200 W (other models) 25 4EM-17-174 39-DE60-45650-002 / C2 1 1 2 Model Number Description Voltage Max. Load Max. Load Min. Load Ripple (Convection) (300 LFM) LFWLT200-1000 Class 1 with Screw Terminal 35.0 A LFWLT200-1000-2 Class 2 with Screw Terminal 5 V 16.67 A 0.0 A 1% LFWLT200-1300 Class 1 with JST Connector 26.0 A LFWLT200-1300-2 Class 2 with JST Connector LFWLT200-1001 Class 1 with Screw Terminal LFWLT200-1001-2 Class 2 with Screw Terminal 12 V 13.33 A 0.0 A 1% 16.67 A LFWLT200-1301 Class 1 with JST Connector LFWLT200-1301-2 Class 2 with JST Connector LFWLT200-1002 Class 1 with Screw Terminal LFWLT200-1002-2 Class 2 with Screw Terminal 15 V 10.67 A 0.0 A 1% 13.33 A LFWLT200-1302 Class 1 with JST Connector LFWLT200-1302-2 Class 2 with JST Connector LFWLT200-1003 Class 1 with Screw Terminal LFWLT200-1003-2 Class 2 with Screw Terminal 24 V 6.67 A 0.0 A 1% 8.33 A LFWLT200-1303 Class 1 with ST Connector LFWLT200-1303-2 Class 2 with JST Connector LFWLT200-1004 Class 1 with Screw Terminal LFWLT200-1004-2 Class 2 with Screw Terminal 48 V 3.33 A 0.0 A 1% 4.17 A LFWLT200-1304 Class 1 with JST Connector LFWLT200-1304-2 Class 2 with JST Connector LFWLT200-1005 Class 1 with Screw Terminal LFWLT200-1005-2 Class 2 with Screw Terminal 30 V 5.33 A 0.0 A 1% 6.67 A LFWLT200-1305 Class 1 with JST Connector LFWLT200-1305-2 Class 2 with JST Connector LFWLT200-CK metal cover kit accessory Notes 1. Combined output power from V1, VSTBY and VFAN should not exceed the total output power rating. 2. Ripple is 2% up to 20% load and < 1% above 20% load. Ripple is peak to peak with 20 MHz bandwidth and 10 µF (Tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 3. Fan output voltage tolerance is +/-20%. During V1 full load, VFAN needs min. 20 mA load to be within regulation band. 4. Peak current for fan output is 1 A. 5. Class 1 products have an Earthing tab and Class 2 products (-2 suffix) have no Earthing tab. 6. Specifications are for nominal input voltage, 25°C and max. load unless otherwise stated. 7. PSU is supplied with J3 housing, pin-4 and pin-6 shorted to enable main output without remote on/off feature. 8. Derate output power linearly to 80% from 90 VAC to 80 VAC input. 9. When used in Cover Kit, de-rate output power to 70 % under all operating conditions. 2 Innovations in Power 4EM-17-174 39-DE60-45650-002 / C2 Connectors Connectors J1 Pin 1 AC NEUTRAL J3 Pin 1 +VE REMOTE SENSE Pin 2 AC LINE Pin 2 VFAN (+12 V/0.5 A) Spade Connector (J4) EARTH Pin 3 -VE REMOTE SENSE (Class 1 product only) Pin 4 REMOTE ON/OFF J2 Pin 1, 2, 3 RTN Pin 5 VSTBY (+5 V/1 A, +/-5%) Pin 4, 5, 6 V1 Pin 6 RTN Pin 7 POWER FAIL Pin 8 POWER GOOD Mechanical Specifications AC Input Connector (J1) Molex: 26-60-4030 or equivalent Mating: 09-50-3031; Pins: 08-50-0106 EARTH (J4) Molex: 19705-4301 or equivalent; Mating: 190030001 DC Output Connector (J2) Option 1: Tyco: 2-1776112-3 or equivalent Mating: 13 AWG wire Option 2: JST: B6P-VH-B (LF) (SN) or B6P-VH (LF) (SN) or equivalent Mating: VHR-6M; Pins: SVH-41T-P1.1 Signal Connector (J3) Molex: 22-23-2081 or equivalent Mating: 22-01-2087, Pins: 08-50-0113 Dimensions 5.0 x 3.0 x 1.5 inches (127.0 x 76.2 x 38.1 mm) Weight 325 g EMC Conditions/Description Parameter Criteria Conducted Emissions EN55032-B, CISPR22-B, FCC PART15-B Pass EN 55032 B Radiated Emissions Pass Input Current Harmonics EN 61000-3-2 Class D EN 61000-3-3 Voltage Fluctuation and Flicker Pass ESD Immunity EN 61000-4-2 Level 3, Criterion A EN 61000-4-3 Radiated Field Immunity Level 3, Criterion A Electrical Fast Transient Immunity EN 61000-4-4 Level 3, Criterion A EN 61000-4-5 Surge Immunity Level 3, Criterion A Conducted Immunity EN 61000-4-6 Level 3, Criterion A EN 61000-4-8 Magnetic Field Immunity Level 3, Criterion A Voltage dips, interruptions EN 61000-4-11 Criterion A & B Safety CE Mark Complies with LVD Directive Approval Agency Nemko, UL Safety Standard(s) UL/CSA C22.2 No./IEC/EN60950-1 (ed.2) Safety File Number(s) Nemko: P15220619; CB: NO90058; UL: E150565 27 4EM-17-174 39-DE60-45650-002 / C2 Signal Power Good Signal TTL signal goes high after main output is within regulation band, delay is 0.1 to 0.3 s Power Fail Signal TTL signal goes low 1 ms advance before output goes out of regulation due to mains failure Remote Sense Compensates for 200 mV drop Remote on/off To turn on PSU short remote pin to ground Derating Curve Convection load: 83W up to 40 °C De-rate above 40 °C @ 1.89% per °C Forced air cooled load : 130W up to 50°C (for screw terminal version) De-rate above 50 °C @ 1.63% per °C Forced air cooled load : 175W up to 50°C (for JST connector version) De-rate above 50 °C @ 2.5% per °C Convection load: 160W up to 40 °C De-rate above 40 °C @ 2% per °C Forced air cooled load : 200W up to 50°C De-rate above 50 °C @ 2.5% per °C 4 Innovations in Power 4EM-17-174 39-DE60-45650-002 / C2 Mechanical Drawing Notes: In case the PCB is mounted in a metal enclosure, using metal hardware ensure the following 1. Stand off, used to mount PCB has OD of 5.4 mm max. 2. Screws, used to fix PCB on stand off, have head dia of 6.0 mm max. 3. Washer, if used, to have dia of 6.5 mm max. 29 4EM-17-174 39-DE60-45650-002 / C2
Frequently asked questions
How does Electronics Finder differ from its competitors?

Is there a warranty for the WLT200-CK?

Which carrier will Electronics Finder use to ship my parts?

Can I buy parts from Electronics Finder if I am outside the USA?

Which payment methods does Electronics Finder accept?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods